[Wg-test-framework] Disk failure in merlot1.test-lab.xenproject.org

[Ian Jackson <Ian.Jackson@xxxxxxxxxxxxx>]

(First sent on the 26th of January and pinged on the 8th of February.
Resending the whole mail to adjust the recipient headers...)

The hard disk in merlot1 seems to have failed.  See information below.

I think we need to get the disk replaced under warranty.  How would
you like to proceed ?


The Linux kernel (in d-i) reports:

Jan 26 11:08:30 kernel: [60981.877537] sd 3:0:0:0: [sda] Unhandled sense code
Jan 26 11:08:30 kernel: [60981.877544] sd 3:0:0:0: [sda]  
Jan 26 11:08:30 kernel: [60981.877547] Result: hostbyte=DID_OK 
driverbyte=DRIVER_SENSE
Jan 26 11:08:30 kernel: [60981.877551] sd 3:0:0:0: [sda]  
Jan 26 11:08:30 kernel: [60981.877553] Sense Key : Medium Error [current] 
Jan 26 11:08:30 kernel: [60981.877558] sd 3:0:0:0: [sda]  
Jan 26 11:08:30 kernel: [60981.877561] Add. Sense: Unrecovered read error
Jan 26 11:08:30 kernel: [60981.877564] sd 3:0:0:0: [sda] CDB: 
Jan 26 11:08:30 kernel: [60981.877566] Read(10): 28 00 00 00 0a 00 00 00 08 00
Jan 26 11:08:30 kernel: [60981.877718] sd 3:0:0:0: [sda] Unhandled sense code
Jan 26 11:08:30 kernel: [60981.877722] sd 3:0:0:0: [sda]  
Jan 26 11:08:30 kernel: [60981.877725] Result: hostbyte=DID_OK 
driverbyte=DRIVER_SENSE
Jan 26 11:08:30 kernel: [60981.877728] sd 3:0:0:0: [sda]  
Jan 26 11:08:30 kernel: [60981.877730] Sense Key : Medium Error [current] 
Jan 26 11:08:30 kernel: [60981.877734] sd 3:0:0:0: [sda]  
Jan 26 11:08:30 kernel: [60981.877737] Add. Sense: Unrecovered read error
Jan 26 11:08:30 kernel: [60981.877740] sd 3:0:0:0: [sda] CDB: 
Jan 26 11:08:30 kernel: [60981.877742] Read(10): 28 00 00 00 0a 00 00 00 08 00

According to the Linux boot messages this disk is:

Jan 26 11:07:55 kernel: [60946.677740] scsi 3:0:0:0: Direct-Access     HP       
LOGICAL VOLUME   6.00 PQ: 0 ANSI: 5

Looking at the BIOS messages:

Slot 0  HP Smart Array P420i Controller        (1 GB, v6.00)  1
Logical Drive

      physicaldrive 1I:2:1
...
         Interface Type: SAS
         Size: 1 TB
         Firmware Revision: HPD8
         Serial Number: 9XG6ZVSM0000W449FJB4
         Model: HP      MM1000FBFVR

I haven't been able to look at the SMART status.  I can't see how to
do this within the HP SSA CLI even after reading the manual [1], and
the d-i fails too soon.


Thanks,
Ian.

[1] http://www.hp.com/ctg/Manual/c03909334

_______________________________________________
Wg-test-framework mailing list
Wg-test-framework@xxxxxxxxxxxxxxxxxxxx
http://lists.xenproject.org/cgi-bin/mailman/listinfo/wg-test-framework