RE: [Xen-ia64-devel] Could you tell me howto run xen on ski?

["Magenheimer, Dan (HP Labs Fort Collins)" <dan.magenheimer@xxxxxx>]

I have often used ski for Xen development but have not tried
it in a few months.  However I never tried to use networking
(simeth).  Did you build the vmlinux with the hpsim config
file or just turn on CONFIG_HP_SIM?   Also I think the command
line options you are specifying may be wrong... I will
have to try it again to check (and may not be able to
try until next week as I am focused on Xen 3.0 release
right now).

> -----Original Message-----
> From: xen-ia64-devel-bounces@xxxxxxxxxxxxxxxxxxx 
> [mailto:xen-ia64-devel-bounces@xxxxxxxxxxxxxxxxxxx] On Behalf 
> Of Matsumoto
> Sent: Friday, December 02, 2005 2:53 AM
> To: xen-ia64-devel@xxxxxxxxxxxxxxxxxxx
> Subject: [Xen-ia64-devel] Could you tell me howto run xen on ski?
> 
> Hi, all
> 
> I am interested in running ski for Xen development.
> 
> First, I tried to run native vmlinux(which is complied with 
> CONFIG_HP_SIM
> and so on).
> 
> But I have not been able to boot vmlinux.
> 
> # xski bootloader vmlinux root=/dev/sda1 
> simscsi=/nue/var/ski-disks/sda
> simeth=eth0
> 
> The result is :
> 
> ==================================================
> 
> loading vmlinux...
> 
> starting kernel...
> 
> Linux version 2.6.12 (root@xxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc 
> version 3.4.4
> 
> 20050721 (Red Hat 3.4.4-2)) #1 SMP Fri Dec 2 13:43:29 JST 
> 2005 EFI v1.00 by
> Hewlett-Packard: SALsystab=0x10a0b8
> 
> warning: unable to switch EFI into virtual mode 
> (status=9223372036854775811)
> No I/O port range found in EFI memory map, falling back to 
> AR.KR0 I/O port
> base = 0xffffc000000
> 
> efi.trim_top: ignoring 2048KB of memory at 0x200000 due to 
> granule hole at
> 0x8000000
> 
> warning: skipping physical page 0
> 
> SAL 0.1: Hewlett-Packard HP-simulator version 0.0 No logical 
> to physical
> processor mapping available
> 
> get_max_cacheline_size: ia64_pal_cache_summary() failed (status=-1)
> PAL_VM_PAGE_SIZE failed with status=-1;defaulting to architected purge
> page-sizes.
> 
> cpu_init: PAL VM summary failed, assuming 18 RID bits MCA related
> initialization done Virtual mem_map starts at 
> 0xa0007fffff1e4000 Built 1
> zonelists Kernel command line: root=/dev/sda1 
> simscsi=/root/ski/xenia64.img
> simeth=eth0 PID hash table entries: 1024 (order: 10, 32768 bytes) :-<
> "Processing stops here. "
> 
> ==================================================
> 
> Did I mistake anything?
> 
> Please tell me howto run xen on ski if anyone use ski.
> 
> Thanks,
> 
> Nakato
> 
> 
> 
> _______________________________________________
> Xen-ia64-devel mailing list
> Xen-ia64-devel@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-ia64-devel
> 

_______________________________________________
Xen-ia64-devel mailing list
Xen-ia64-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-ia64-devel