Re: [Xen-users] xen 3.0 boot problem

[The Smoking Man <datashark@xxxxxxxxx>]

Beein used here the qla2344 on several boxes. works  trully
fine  on  gentoo-xensources (vanilla kernel plus xen patches)
and (this is what i'm using in production) with suse kotd sources. 

Bellow is the relevant bootlog... 

Best regards,

[    6.599201] QLogic Fibre Channel HBA Driver
[    6.599446] ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 29 (level, low) -> IRQ 29
[    6.599749] qla2300 0000:02:04.0: Found an ISP2312, irq 29, iobase 0xe8804000
[    6.600392] qla2300 0000:02:04.0: Configuring PCI space...
[    6.600687] qla2300 0000:02:04.0: Configure NVRAM parameters...
[    6.685681] qla2300 0000:02:04.0: Verifying loaded RISC code...
[    6.809175] qla2300 0000:02:04.0: Waiting for LIP to complete...
[   27.200114] qla2300 0000:02:04.0: Cable is unplugged...
[   27.200289] scsi0 : qla2xxx
[   27.200579] qla2300 0000:02:04.0:
[   27.200580]  QLogic Fibre Channel HBA Driver: 8.00.02b5-k
[   27.200581]   QLogic QLA2344 -
[   27.200582]   ISP2312: PCI-X (133 MHz) @ 0000:02:04.0 hdma+, host#=0, fw=3.03.08 IPX
[   27.201211] ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 30 (level, low) -> IRQ 30
[   27.201482] qla2300 0000:02:04.1: Found an ISP2312, irq 30, iobase 0xe8806000
[   27.202082] qla2300 0000:02:04.1: Configuring PCI space...
[   27.202369] qla2300 0000:02:04.1: Configure NVRAM parameters...
[   27.287483] qla2300 0000:02:04.1: Verifying loaded RISC code...
[   27.410625] qla2300 0000:02:04.1: Waiting for LIP to complete...
[   47.810115] qla2300 0000:02:04.1: Cable is unplugged...
[   47.810279] scsi1 : qla2xxx
[   47.810504] qla2300 0000:02:04.1:
[   47.810505]  QLogic Fibre Channel HBA Driver: 8.00.02b5-k
[   47.810507]   QLogic QLA2344 -
[   47.810508]   ISP2312: PCI-X (133 MHz) @ 0000:02:04.1 hdma+, host#=1, fw=3.03.08 IPX
[   47.811136] ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 31 (level, low) -> IRQ 31
[   47.811404] qla2300 0000:02:06.0: Found an ISP2312, irq 31, iobase 0xe881a000
[   47.812006] qla2300 0000:02:06.0: Configuring PCI space...
[   47.812295] qla2300 0000:02:06.0: Configure NVRAM parameters...
[   47.897025] qla2300 0000:02:06.0: Verifying loaded RISC code...
[   48.020170] qla2300 0000:02:06.0: Waiting for LIP to complete...
[   68.410104] qla2300 0000:02:06.0: Cable is unplugged...
[   68.410270] scsi2 : qla2xxx
[   68.410514] qla2300 0000:02:06.0:
[   68.410515]  QLogic Fibre Channel HBA Driver: 8.00.02b5-k
[   68.410517]   QLogic QLA2344 -
[   68.410518]   ISP2312: PCI-X (133 MHz) @ 0000:02:06.0 hdma+, host#=2, fw=3.03.08 IPX
[   68.411144] ACPI: PCI Interrupt 0000:02:06.1[B] -> GSI 28 (level, low) -> IRQ 28
[   68.411413] qla2300 0000:02:06.1: Found an ISP2312, irq 28, iobase 0xe881c000
[   68.412024] qla2300 0000:02:06.1: Configuring PCI space...
[   68.412311] qla2300 0000:02:06.1: Configure NVRAM parameters...
[   68.497424] qla2300 0000:02:06.1: Verifying loaded RISC code...
[   68.516876] qla2300 0000:02:06.1: Waiting for LIP to complete...
[   69.020063] qla2300 0000:02:06.1: LIP reset occured (f8f7).
[   69.020220] qla2300 0000:02:06.1: LIP occured (f8f7).
[   69.020370] qla2300 0000:02:06.1: LOOP UP detected (2 Gbps).
[   69.020661] qla2300 0000:02:06.1: Topology - (Loop), Host Loop address 0x0
[   69.021595] scsi3 : qla2xxx
[   69.021824] qla2300 0000:02:06.1:
[   69.021825]  QLogic Fibre Channel HBA Driver: 8.00.02b5-k
[   69.021826]   QLogic QLA2344 -
[   69.021827]   ISP2312: PCI-X (133 MHz) @ 0000:02:06.1 hdma+, host#=3, fw=3.03.08 IPX
[   69.025082] mice: PS/2 mouse device common for all mice
[   69.025227] md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
[   69.025434] NET: Registered protocol family 2
[   69.025850]   Vendor: DotHill   Model: SANnet II FC      Rev: 327R
[   69.026240]   Type:  
Direct-Access                     
ANSI SCSI revision: 03
[   69.027076] SCSI device sda: 131072 512-byte hdwr sectors (67 MB)
[   69.027919] SCSI device sda: drive cache: write through
[   69.028521] SCSI device sda: 131072 512-byte hdwr sectors (67 MB)
[   69.029354] SCSI device sda: drive cache: write through
[   69.029495]  sda: sda1
[   69.030035] Attached scsi disk sda at scsi3, channel 0, id 0, lun 0
[   69.031081]   Vendor: DotHill   Model: SANnet II FC      Rev: 327R
[   69.031466]   Type:  
Direct-Access                     
ANSI SCSI revision: 03
[   69.032195] SCSI device sdb: 2097152 512-byte hdwr sectors (1074 MB)
[   69.032943] SCSI device sdb: drive cache: write through
[   69.033469] SCSI device sdb: 2097152 512-byte hdwr sectors (1074 MB)
[   69.034213] SCSI device sdb: drive cache: write through
[   69.034353]  sdb: sdb1
[   69.048548] Attached scsi disk sdb at scsi3, channel 0, id 0, lun 1
[   69.049188]   Vendor: DotHill   Model: SANnet II FC      Rev: 327R
[   69.049573]   Type:  
Direct-Access                     
ANSI SCSI revision: 03
[   69.050305] SCSI device sdc: 12582912 512-byte hdwr sectors (6442 MB)
[   69.051056] SCSI device sdc: drive cache: write through
[   69.051586] SCSI device sdc: 12582912 512-byte hdwr sectors (6442 MB)
[   69.052341] SCSI device sdc: drive cache: write through
[   69.052481]  sdc: sdc1
[   69.065097] Attached scsi disk sdc at scsi3, channel 0, id 0, lun 2
[   69.065589]   Vendor: DotHill   Model: SANnet II FC      Rev: 327R
[   69.065973]   Type:  
Direct-Access                     
ANSI SCSI revision: 03
[   69.066583] SCSI device sdd: 12582912 512-byte hdwr sectors (6442 MB)
[   69.067279] SCSI device sdd: drive cache: write through
[   69.067695] SCSI device sdd: 12582912 512-byte hdwr sectors (6442 MB)
[   69.068303] SCSI device sdd: drive cache: write through
[   69.068442]  sdd: sdd1
[   69.078452] Attached scsi disk sdd at scsi3, channel 0, id 0, lun 3
[   69.078969]   Vendor: DotHill   Model: SANnet II FC      Rev: 327R
[   69.079355]   Type:  
Direct-Access                     
ANSI SCSI revision: 03
[   69.080403] SCSI device sde: 12582912 512-byte hdwr sectors (6442 MB)
[   69.081042] SCSI device sde: drive cache: write through
[   69.081458] SCSI device sde: 12582912 512-byte hdwr sectors (6442 MB)
[   69.082098] SCSI device sde: drive cache: write through
[   69.082237]  sde: sde1
[   69.093087] Attached scsi disk sde at scsi3, channel 0, id 0, lun 4
[   69.093592]   Vendor: DotHill   Model: SANnet II FC      Rev: 327R
[   69.093976]   Type:  
Direct-Access                     
ANSI SCSI revision: 03
[   69.094591] SCSI device sdf: 12582912 512-byte hdwr sectors (6442 MB)
[   69.095206] SCSI device sdf: drive cache: write through
[   69.095615] SCSI device sdf: 12582912 512-byte hdwr sectors (6442 MB)
[   69.096234] SCSI device sdf: drive cache: write through
[   69.096373]  sdf: sdf1
[   69.108174] Attached scsi disk sdf at scsi3, channel 0, id 0, lun 5
[   69.108790]   Vendor: DotHill   Model: SANnet II FC      Rev: 327R
[   69.109175]   Type:  
Direct-Access                     
ANSI SCSI revision: 03
[   69.110034] SCSI device sdg: 12582912 512-byte hdwr sectors (6442 MB)
[   69.110638] SCSI device sdg: drive cache: write through
[   69.111046] SCSI device sdg: 12582912 512-byte hdwr sectors (6442 MB)
[   69.111645] SCSI device sdg: drive cache: write through
[   69.111784]  sdg: sdg1
[   69.122286] Attached scsi disk sdg at scsi3, channel 0, id 0, lun 6
[   69.122777]   Vendor: DotHill   Model: SANnet II FC      Rev: 327R
[   69.123163]   Type:  
Direct-Access                     
ANSI SCSI revision: 03
[   69.123772] SCSI device sdh: 2097152 512-byte hdwr sectors (1074 MB)
[   69.124377] SCSI device sdh: drive cache: write through
[   69.124789] SCSI device sdh: 2097152 512-byte hdwr sectors (1074 MB)
[   69.125393] SCSI device sdh: drive cache: write through
[   69.125532]  sdh: sdh1
[   69.134481] Attached scsi disk sdh at scsi3, channel 0, id 0, lun 7
[   69.134971]   Vendor: DotHill   Model: SANnet II FC      Rev: 327R
[   69.135355]   Type:  
Direct-Access                     
ANSI SCSI revision: 03
[   69.135974] SCSI device sdi: 2097152 512-byte hdwr sectors (1074 MB)
[   69.136577] SCSI device sdi: drive cache: write through
[   69.136994] SCSI device sdi: 2097152 512-byte hdwr sectors (1074 MB)
[   69.137597] SCSI device sdi: drive cache: write through
[   69.137736]  sdi: sdi1
[   69.142544] Attached scsi disk sdi at scsi3, channel 0, id 0, lun 8
[   69.143037]   Vendor: DotHill   Model: SANnet II FC      Rev: 327R
[   69.143421]   Type:  
Direct-Access                     
ANSI SCSI revision: 03
[   69.144036] SCSI device sdj: 2097152 512-byte hdwr sectors (1074 MB)
[   69.144635] SCSI device sdj: drive cache: write through
[   69.145044] SCSI device sdj: 2097152 512-byte hdwr sectors (1074 MB)
[   69.145640] SCSI device sdj: drive cache: write through
[   69.145780]  sdj:<6>IP: routing cache hash table of 8192 buckets, 64Kbytes
[   69.150433] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[   69.151333] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[   69.151870] TCP: Hash tables configured (established 131072 bind 65536)
[   69.152110] NET: Registered protocol family 1
[   69.153802]  unknown partition table
[   69.153959] Attached scsi disk sdj at scsi3, channel 0, id 0, lun 9
[   69.154482]   Vendor: DotHill   Model: SANnet II FC      Rev: 327R
[   69.154867]   Type:  
Direct-Access                     
ANSI SCSI revision: 03
[   69.155484] SCSI device sdk: 2097152 512-byte hdwr sectors (1074 MB)
[   69.156083] SCSI device sdk: drive cache: write through
[   69.156502] SCSI device sdk: 2097152 512-byte hdwr sectors (1074 MB)
[   69.157095] SCSI device sdk: drive cache: write through
[   69.157234]  sdk: unknown partition table
[   69.168099] Attached scsi disk sdk at scsi3, channel 0, id 0, lun 10

On 10/5/05, Ian Pratt <m+Ian.Pratt@xxxxxxxxxxxx> wrote:

Has anyone used xen succefully with a qla2300?

What machines have this card?

Ian

> I've installed Xen 3.0-devel on SUSE Linux without any problems.
> But when i tryed to boot the system, i've got a funny problem:
>
> qla2300 0000:05:01.0: Found an ISP2312, irq 185, iobase
> 0xf8812000 qla2300 0000:05:01.0: Configuring PCI space...
> qla2300 0000:05:01.0: Configure NVRAM parameters...
> qla2300 0000:05: 01.0: Verifying loaded RISC code...
> qla2300 0000:05:01.0: Waiting for LIP to complete...
>
> until here all works fine, but then:
>
> input: PS/2 Generic Mouse on synaptcs-pt/serio0 qla2300
> 0000:05:01.0: LIP reset occured (f7f7).
> qla2300 0000:05:01.0: LOOP UP detected (2 Gbps).
> qla2300 0000:05:01.0: Topology - (F_Port), Host Loop address 0xffff
> scsi3 : qla2xxx
> qla2300 0000:04: 02.0:
>   QLogic Fibre Channel HBA Driver: 8.01.00b5-k
>   QLogic QLA2340 - 133MHz PCI-X to 2Gb FC, Single Channel
>   ISP2312: PCI-X (100 MHz) @ 0000:05:01.0 hdma+, host#=3,
> fw=3.03.15 IPX
> Loading kernel/fs/reiserfs/reiserfs.ko
> Waiting for device /dev/sda4 to appear: .....not found ---
> exiting to /bin/sh $
>
> if i use the standard (bigsmp) kernel the normal massages are:
>
> SCSI device sda: 41943040 512-byte hdwr sectors (21475 MB)
> SCSI device sda: drive cache: write back SCSI device sda:
> 41943040 512-byte hdwr sectors (21475 MB) SCSI device sda:
> drive cache: write back
>  sda: sda1 sda2 sda3 sda4
> ....usw.
>
> Well, my qla2300 has the storage attached not a generic mouse.
> Of course it isn't possible to boot from this mouse. :-(



_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users