[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-users] Xen and Asterisk/Zapata WORKING!!



You have to assign the card to one domain, so I don't think that would be possible.
Sébastien CRAMATTE wrote:
Jason Clark a écrit :
The zaptel drivers use the zaptel hardware for a timing source, so I haven't had any RTC troubles in my setup. If you have to have asterisk, you may want to consider buying a cheap FXO card and using it instead of the dummy driver.

I will consider this option  ... Thanks a lot
It's possible to use  timer of an FXO card  accross different domU ?


Sébastien CRAMATTE wrote:
Hi,

I've tried to run Asterisk 1.2 from backports.org  inside Xen 3.0.2 VM
For my own  doesn't works ...

As you know  the problem come from  ztdummy  driver that use RTC
and this driver is required for  "conference" module  ...

If I load "rtc.ko" inside dom0 and if I start a domU it tell that IRQ
8  is not free ...
If I try to load it directly in a domU with ztdummy.ko  I obtain this

----------------------
Zaptel cards initial configuration: Zapata Telephony Interface
Registered on major 196
Zaptel Version: 1.2.7 Echo Canceller: KB1
general protection fault: 0000 [#1]
SMP
Modules linked in: zaptel crc_ccitt genrtc
CPU:    0
EIP:    0061:[<c01351a7>]    Not tainted VLI
EFLAGS: 00010282   (2.6.16.19-xen #1)
EIP is at print_unload_info+0x39/0xf1
eax: 00000000   ebx: fdfefe7f   ecx: c035d18d   edx: 00001000
esi: c9046a60   edi: c83238c0   ebp: c9046a60   esp: c87e3ef8
ds: 007b   es: 007b   ss: 0069
Process modprobe (pid: 885, threadinfo=c87e2000 task=c11f6030)
Stack: <0>c83238c0 c035d189 0003ffff 00000000 c9046a64 c9046a60 c83238c0
00000400
      c0137777 c83238c0 c9046a60 c9046a6c 00037064 c9046a64 c83238c0
c9046a64
      c017d1a3 c83238c0 c9046a64 c848fa34 00000000 c87e2000 00000022
00000000
Call Trace:
[<c0137777>] m_show+0x44/0xa8
[<c017d1a3>] seq_read+0xe1/0x2b8
[<c015d1fa>] vfs_read+0xa4/0x16f
[<c015d598>] sys_read+0x51/0x80
[<c0104d15>] syscall_call+0x7/0xb
Code: 24 c7 44 24 0c 00 00 00 00 89 2c 24 e8 d7 fd ff ff 89 3c 24 89 44
24 08 c7 44 24 04 89 d1 35 c0 e8 85 85 04 00 8b 9d 00 05 00 00 <8b> 03
0f 18 00 90 8d b5 00 05 00 00 39 f3 74 2e c7 44 24 0c 01
/etc/rc2.d/S15zaptel: line 136:   885 Segmentation fault      modprobe
ztdummy
<6>Registered tone zone 0 (United States / North America)
zaptel.
-------------------

I've read somewhere that is possible to disable rtc un in ztdummy  (
#Define USE_RTC)
http://lists.xensource.com/archives/html/xen-devel/2006-05/msg00962.html

Does anyone have experience or solution to this problem ?

Regards

Sebastien


Duncan Gibb a écrit :
On Sun, 2006-08-13 at 23:56, Jason wrote:

J> thought I would post how I got asterisk playing well
J> in a DomU with an X100P FXO card.

Good to know someone else is also playing with this.  Could you post a
bit more detail about when your Xen snapshot was taken, the config
options and the hardware you're using, please?

I have a 600MHz P-III system on which I want to use a Xen domU to
develop zaptel modules without worrying about bringing down the machine
when I get it wrong.

Using Xen 3.0.2-2 and the standard 2.6.16-xen kernel lightly
reconfigured (1000Hz, serial enabled) almost worked, but the jitter was so bad voicemails were incomprehensible (even when left by SIP). Dialling out on an analogue line with a clone wcfxo card worked only intermittently because the DTMF synthesis broke up towards the end of a
10-digit UK number.


CPU load didn't seem to be the problem, and Googling around suggested a
working RTC might help.  I have therefore rebuilt with the Xen nightly
snapshot from Sunday and 2.6.16.13-xen. I'm not convinced that the RTC
does actually work (still get IRQ 8 not free sometimes), and wcfxo
frequently reports it can't init the DAA (ie interrupts are probably not
working in the domU).

I've tried both passthrough and vpci pci backend drivers.  And I've
turned on permissive mode after seeing warnings when doing modprobe
wcfxo in the domU.


J> The first thing I did was to give up trying to get the zaptel
J> modules to compile in a DomU.   I never did get that part working.

My solution to this was to copy the linux build tree from the dom0 over
to /usr/src in the domU, along with the xen tree and the
linux-2.6-xen-sparse tree and symlinking as you did.


Cheers


Duncan



_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users





_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users










_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users


 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.