Xen project Mailing List

[Xen-users] pciback not working with linux domU

From: Wong Louis <mylover01ca@xxxxxxxxx>

Date: Mon, 20 Nov 2006 05:52:22 -0500 (EST)

Delivery-date: Mon, 20 Nov 2006 02:52:46 -0800

Domainkey-signature: a=rsa-sha1; q=dns; c=nofws; s=s1024; d=yahoo.com; h=X-YMail-OSG:Received:Date:From:Subject:To:MIME-Version:Content-Type:Content-Transfer-Encoding:Message-ID; b=AvLr6oD3TOD1kprhYxzf5QbBDMrOsdkHSLobw4jDQ5vtQGi5j/LTFL5TtN+wR/j36V95CupiJFWQicXZn3vWa05f3QhsakvMGwmoTlvS5DdXeyMEnFejvR2jCX/DNMWD2r8ZcmjznYnEL+vwDgPYe/fX6tOODlre78ax+jfTYFo=;

List-id: Xen user discussion <xen-users.lists.xensource.com>

I am using the latest xen unstable and trying to install this 00:19.0 Ethernet controller: Intel Corporation 82562V 10/100 Network Connection (rev 02) since xen uses 2.6.16.29 it does not support it yet, someone said (on google) that 2.6.18.3 supports it. So I want to boot 2.6.18.3 in domU and enable it with the pciback thing. my seize commands are: echo -n 0000:00:19.0 > /sys/bus/pci/drivers/pciback/new_slot echo -n 0000:00:19.0 > /sys/bus/pci/drivers/pciback/bind (results from dmesg) pciback: wants to seize 0000:00:19.0 pciback 0000:00:19.0: probing... pciback 0000:00:19.0: seizing device pciback 0000:00:19.0: pcistub_device_alloc pciback 0000:00:19.0: initializing... pciback 0000:00:19.0: initializing config pciback 0000:00:19.0: initializing virtual configuration space pciback 0000:00:19.0: added config field at offset 0x04 pciback 0000:00:19.0: added config field at offset 0x3c pciback 0000:00:19.0: added config field at offset 0x3d pciback 0000:00:19.0: added config field at offset 0x0c pciback 0000:00:19.0: added config field at offset 0x0d pciback 0000:00:19.0: added config field at offset 0x0f pciback 0000:00:19.0: added config field at offset 0x10 pciback 0000:00:19.0: added config field at offset 0x14 pciback 0000:00:19.0: added config field at offset 0x18 pciback 0000:00:19.0: added config field at offset 0x1c pciback 0000:00:19.0: added config field at offset 0x20 pciback 0000:00:19.0: added config field at offset 0x24 pciback 0000:00:19.0: added config field at offset 0x30 pciback 0000:00:19.0: Found capability 0x1 at 0xc8 pciback 0000:00:19.0: added config field at offset 0xc8 pciback 0000:00:19.0: added config field at offset 0xca pciback 0000:00:19.0: added config field at offset 0xce pciback 0000:00:19.0: added config field at offset 0xcf pciback 0000:00:19.0: enabling device ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 19 pciback 0000:00:19.0: reset device ACPI: PCI interrupt for device 0000:00:19.0 disabled --- I put pci=['0000:00:19.0'] in the hvm file, when it boots it says: pciback pci-1-0: allocated pdev @ 0xf2f72a40 pciback pci-1-0: getting be setup pciback pci-1-0: exporting dom 0 bus 0 slot 19 func 0 pciback: vpci: 0000:00:19.0: assign to virtual slot 0 pciback pci-1-0: Publishing pci roots pciback pci-1-0: writing root 0 at 0000:00 pciback pci-1-0: fe state changed 1 but inside the domU the lspci does not show the device. __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com _______________________________________________ Xen-users mailing list Xen-users@xxxxxxxxxxxxxxxxxxx http://lists.xensource.com/xen-users

©2013 Xen Project, A Linux Foundation Collaborative Project. All Rights Reserved.
Linux Foundation is a registered trademark of The Linux Foundation.
Xen Project is a trademark of The Linux Foundation.