Hello,
I am facing some problem in booting up a DomU in Xen 3.2 (Installed on top of a FC8-64bit).
I installed FC8 without virtualization and on top of that installed Xen 3.2 (compiled from source). I used "make world" and "make install" for my compilation.
After this my Dom0 boots up fine. But when I try to boot a domU using the same (dom 0)kernel (with the file system and swap image being Fedora 64 images obtained from
Jailtime.org), the boot process continues for some time and then stops. I am including below the entire boot messages obtained on the console.
(The same file system and swap image worked properly with a Xen 3.1 Dom0 kernel).
So can any one tell me whats going wrong? Is some thing wrong with my compiled kernel? Did I miss some
configuration due to "make world"?
Please reply. If some other information is needed I can provide that. But this is a bit urgent and I will really appreciate any help.
If any one was able to install a domU properly on a FC8 + Xen 3.2 configuration (without any external tools like virt-manager/virt-install) please let me know the procedure.
Regards
Dushmanta
<<<<<<<<<<<<<<
[root@dmcomp xen-domU]# xm create -c fedora.fc8.64.xen3.cfg
Using config file "./fedora.fc8.64.xen3.cfg".
Started domain fedora.fc8.64
Bootdata ok (command line is root=/dev/sda1 fastboot)
Linux version 2.6.18.8-xen (root@dmcomp) (gcc version 4.1.2 20070925 (Red Hat 4.1.2-33)) #1 SMP Fri Feb 22 20:24:57 EST 2008
BIOS-provided physical
RAM map:
Xen: 0000000000000000 - 0000000010800000 (usable)
No mptable found.
Built 1 zonelists. Total pages: 66660
Kernel command line: root=/dev/sda1 fastboot
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 16384 bytes)
Xen reported: 1729.515 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Software IO TLB disabled
Memory: 242932k/270336k available (2015k kernel code, 19184k reserved, 882k data, 176k init)
Calibrating delay using timer specific routine.. 3460.36 BogoMIPS (lpj=17301823)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
SMP alternatives: switching to UP
code
Freeing SMP alternatives: 24k freed
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 9684k freed
NET: Registered protocol family 16
Brought up 1 CPUs
PCI: setting up Xen PCI frontend stub
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
xen_mem: Initialising balloon driver.
PCI: System does not support PCI
PCI: System does not support PCI
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 3, 32768 bytes)
TCP established hash table entries: 16384 (order: 6, 262144 bytes)
TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
IA-32 Microcode Update Driver: v1.14a-xen <
tigran@xxxxxxxxxxx>
audit: initializing netlink socket (disabled)
audit(1204694388.919:1):
initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
rtc: IRQ 8 is not free.
Non-volatile memory driver v1.2
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Xen virtual console successfully installed as xvc0
Event-channel device installed.
netfront: Initialising virtual ethernet driver.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
PNP: No PS/2 controller found. Probing ports directly.
i8042.c: No controller found.
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET:
Registered protocol family 1
NET: Registered protocol family 17
xen-vbd: registered block device major 8
blkfront: sda1: barriers enabled
blkfront: sda2: barriers enabled
XENBUS: Device with no driver: device/console/0
BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
EDD information not available.
Freeing unused kernel memory: 176k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
SCSI subsystem initialized
register_blkdev: cannot get major 8 for sd
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised:
dm-devel@xxxxxxxxxxEXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data
mode.
>>>>>>>>>>>>>>>>>
The config file I am using for booting domU is:
kernel = "/boot/vmlinuz-2.6.18.8-xen"
ramdisk = "/boot/initrd-2.6.18.8-xen.img"
memory = 256
name = "fedora.fc8.64"
vif = [ '' ]
#dhcp= "dhcp"
#disk = ['file:/xen/fedora/fedora.fc8.64.img,sda1,w', 'file:/xen/fedora/fedora.swap,sda2,w']
disk = ['file:/home/dmpatra/Xen_Downloads/xen-domU/fedora.fc8.64.img,sda1,w', 'file:/home/dmpatra/Xen_Downloads/xen-domU/fedora.swap,sda2,w']
root = "/dev/sda1"
extra = "fastboot"
