RE: [Xen-users] Dedicate NIC's to DomU's

["Joseph L. Casale" <JCasale@xxxxxxxxxxxxxxxxx>]

You need to actually start the bridge, or at least query it for status but its 
obviously not running.
Look at thge output from it as you ran it.
sh /etc/xen/scripts/multi-network-bridge start
jlc

________________________________________
From: xen-users-bounces@xxxxxxxxxxxxxxxxxxx 
[xen-users-bounces@xxxxxxxxxxxxxxxxxxx] On Behalf Of Hans Pfeil [HPfeil@xxxxxxx]
Sent: Monday, June 09, 2008 1:12 PM
To: xen-users@xxxxxxxxxxxxxxxxxxx
Subject: [Xen-users] Dedicate NIC's to DomU's

Joe, no bridges.  Here is a new set of info.

:~ # ifconfig
eth0      Link encap:Ethernet  HWaddr 00:0F:1F:04:0B:49
          inet addr:xxx.xxx.xxx.xx  Bcast:xxx.xxx.xxx.xxx  Mask:255.255.255.0
          inet6 addr: fe80::20f:1fff:fe04:b49/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:139 errors:0 dropped:0 overruns:0 frame:0
          TX packets:137 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:21227 (20.7 Kb)  TX bytes:12940 (12.6 Kb)
          Interrupt:17

eth1      Link encap:Ethernet  HWaddr 00:0F:1F:04:0B:4A
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:18

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:111 errors:0 dropped:0 overruns:0 frame:0
          TX packets:111 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:7079 (6.9 Kb)  TX bytes:7079 (6.9 Kb)

:~ # sh /etc/xen/scripts/multi-network-bridge
Unknown command:
Valid commands are: start, stop, status
Unknown command:
Valid commands are: start, stop, status
:~ #

# cat /etc/xen/scripts/multi-network-bridge
#!/bin/sh
dir=$(dirname "$0")
"$dir/network-bridge" "$@" vifnum=0 netdev=eth0 bridge=eth0
"$dir/network-bridge" "$@" vifnum=1 netdev=eth1 bridge=eth1



-Hans


Heh, you have no bridges, and I suspect it is becuase of that.
Use my script _as is_ and reboot. See what happens :)


jlc



_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users