[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-users] xen network problen domU


  • To: ëìë <peb1611@xxxxxxxxx>, "Fajar A. Nugraha" <fajar@xxxxxxxxx>
  • From: Fasiha Ashraf <feehapk@xxxxxxxxxxx>
  • Date: Wed, 23 Dec 2009 14:10:57 +0530 (IST)
  • Cc: xen-users@xxxxxxxxxxxxxxxxxxx
  • Delivery-date: Wed, 23 Dec 2009 00:42:17 -0800
  • Domainkey-signature: a=rsa-sha1; q=dns; c=nofws; s=s1024; d=yahoo.co.in; h=Message-ID:X-YMail-OSG:Received:X-Mailer:Date:From:Subject:To:Cc:MIME-Version:Content-Type; b=TVS8qzwJJqtkeEzSEETJpEQk+tPlnkFWbI4NG0HpsRd/FDEdIfWmErah9uxK8tueaywuZFes33NEBe/FHtp2wyNKGkDRQ0IT56EhJrKyT2H5lbOsTBlAb9S9xJF+M/CwWqwln0Sv8UIw+D/rXILs2ITRAZ2m+TRyZftSS6Qzzlg=;
  • List-id: Xen user discussion <xen-users.lists.xensource.com>

Remember doing service network restart after saving changes to eth0 interface

Regards,
Fasiha Ashraf


As Fajar said that for a bridged connection you don't need  ip settings inside domU config. As in communication takes place using Mac addresses. So you just need simply to access your domU GUI using VNC. Login as root go to System -> Administration ->Network -> double click your eth0 (inactive)-> inside Hardware device tab
change your mac by clicking probe. Note down the new mac and write the same new one inside domU config file to avoid further inconvenience.  Like this
vif = [ 'mac= 00:xx:xx:xx, bridge=eth0' ]

Regards,
Fasiha Ashraf

--- On Wed, 23/12/09, Fajar A. Nugraha <fajar@xxxxxxxxx> wrote:

From: Fajar A. Nugraha <fajar@xxxxxxxxx>
Subject: Re: [Xen-users] xen network problen domU
To: "ëìë" <peb1611@xxxxxxxxx>
Cc: xen-users@xxxxxxxxxxxxxxxxxxx
Date: Wednesday, 23 December, 2009, 6:39 AM

On Tue, Dec 22, 2009 at 8:57 PM, ëìë <peb1611@xxxxxxxxx> wrote:
> #ifconfig -a (dom0)
> eth0      Link encap:Ethernet  HWaddr 00:16:cb:a5:dd:66
>           inet addr:147.46.125.xx Bcast:147.46.125.255  Mask:255.255.255.0

> # ifconfig -a (domU)
> eth0      Link encap:Ethernet  HWaddr 00:16:3e:1f:4f:46
>           inet addr:192.168.1.101  Bcast:192.168.1.255  Mask:255.255.255.0

> and my domU configuration file

>       vif = [ 'bridge=eth0' ]
>       ip = "192.168.0.101"
>       netmask= "255.255.255.0"
>       gateway = "192.168.0.1"

> I can found similar problem on internet, but I don't understand why does
> hoster's bridged setup is problematic.

First of all, are you using bridged setup or routed setup? If you use
bridge, you wouldn't need to specify ip, netmask, or gateway on domU
config file. Also, if using bridges setup, dom0 bridge IP address (in
your case it's called eth0) should be on the same segment as domU's
network interface. You're using two different segments.

--
Fajar

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users


The INTERNET now has a personality. YOURS! See your Yahoo! Homepage.


The INTERNET now has a personality. YOURS! See your Yahoo! Homepage.
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users

 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.