[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-users] [Xen-devel] Xen VGA Passthrough - GTX 680 successfully ïhard-moded to GRID K2



On Tue, 24 Sep 2013 20:46:52 +0100 (BST), David TECHER <davidtecher@xxxxxxxx> wrote:

- VM = Win XP 64: if I set RAM > 3GB then the VM get slower. VM gets
slower once NVIDIA driver is installed and that I restarted thsi VM
:(. I tried a couple of things but unfortunately I was not to fix it.

That is really weird - I haven't observed any obvious slowdown
related to memory amount in XP64.

Setting RAM  DVI-I Connector
----------------------------------------
The dom0 has just started. There are two VMs (one XP 64 and one Win 7
64)

Start XP 64...OK--> Screen works!
Stop XP 64...OK--> Screen works!
Start XP 64...OK--> Screen works!
Restart XP 64...OK--> Screen works!
Stop XP 64...OK--> Screen works!
Start Win7 64 ...OK--> Screen works!
Stop Win 64...OK--> Screen works!
Start XP 64...KO ---> Black screen!!!
xl destroy for this VM. And VM Win 7 64 can start properly...Screen
works

Output B => DVI Connector
-------------------------------------
The dom0 has just started. There are two VMs (one XP 64 and one Win 7
64)
Start XP 64...OK --> Screen works!

Stop XP 64...OK--> Screen works!
Start XP 64...OK--> Screen works!
Restart XP 64...OK--> Screen works!
Stop XP 64...OK--> Screen works!
Start Win7 64 ...OK--> Screen works!
Stop Win7 64...OK--> Screen works!
Start XP 64...KO ---> Black screen!!!
xl destroy for this VM. And Win 7 64 can start properly...Screen works

Output C ==> mini HDMI

--------------------------------
The dom0 has just started. There are two VMs (one XP 64 and one Win 7
64)
Start XP 64...OK--> Screen works!
Stop XP 64...OK--> Screen works!
Start XP 64...OK--> Screen works!
Restart XP 64...OK--> Screen works!
Stop XP 64...OK--> Screen works!
Start Win7 64 ...OK--> Screen works!
Stop Win7 64...OK--> Screen works!
Start XP 64...KO --> Black Screen.
xl destroy for this VM. And Win 7 64 can start properly...Screen works

Conclusion: whatever the connector is it seems doable to restart XP 64
( no switch to Win 7 64!)

This is presumably with the GTX680?
So it seems to not work is booting XP64 AFTER using Win7.

What I was asking was a little different, though, and
specific to using dual-link DVI vs. single-link. You do,
however, seem to be able to use display-port, which
answers a part of my question, since that doesn't work
for me at all.

Let me recap the problem. I only get this on the GTX680
(Quadrified to K5000 or Gridified to K2, happens in both
cases) in domU. It does NOT happen with a GTX470/480 modified
to Q5000/Q6000. On bare metal the modified GTX680 works fine,
the issue does not arise. I only tried this on XP64, not
attempted on Win7.

Setup:
- Xen 4.3.0
- XP64 domU
- GTX680 modified to K5000

Symptoms:
1) Using a VGA monitor works fine.
2) Using a single-link DVI monitor works fine.
3) Using a monitor capable of dual-link DVI modes but in low
resolution where the card negotiates only a SL-DVI mode
(<= 1280x800 on my Dell 3007WFP) works fine.
4) Using a DL-DVI monitor with high resolution modes
requiring DL-DVI link results in a blank screen (monitor goes
to sleep immediately)
5) DisplayPort use with active DL-DVI adapter results in
monitor going to sleep in ANY mode (low or high res).

In all cases the monitor is identified correctly and it's
specific modes are listed.

So to re-iterate the question - do you have a DL-DVI
monitor you can try connecting to your GTX680 and see
if DL modes work from domU XP64? Note: 1920x1200@60Hz
is achievable using SL-DVI with reduced blanking so not
all monitors that do 1920x1200 are necessarily DL-DVI.
You can check this by looking at the Xorg log file if you
are using the monitor on Linux, it should tell you what
bandwidth is used for the mode. If if it is over 165MHz,
it MUST be DL, if it is below, it may well be SL.

For GTX480/Quadro 6000
====================

The latest VMs I set up were a VM Win 7 64 and a VM Win XP 64. ( = 2
VMs)

- gfx_passthru=0 while setting up the VM -- before installing NVIDIA
drivers. While VMs were setting up I used (native) VNC connection.
(vnc=1)

- gfx_passthru=1 once NVIDIA driver was installed.

No patch was used!

Hang on - are you saying that once the Nvidia driver is installed
you can use gfx_passthry=1 an you get the SeaBIOS output and the
boot-up Windows animaption on the domU monitor, rather than on
the VNC console? Is your passthrough GPU the primary in dom0?

Also note that if you have modified the GTX680 to a Grid K2 (well,
half of a Grid K2), you can actually soft-mod it using a similar
method to the Fermi (4xx series) cards to K5000 (not that there
is much point, mind you). You just have to modify both the
UEFI straps in the UEFI header and the BIOS straps in the normal
BIOS wrapped into all that UEFI garbage (UEFI header is 1024 bytes,
or 0x400 bytes in hex). Or you could just strip out the first 0x400
bytes from the BIOS and all the trailing UEFI garbage after a
little under 64KB - you can tell where the trailing padding starts
by the fact it's all 0xFF filled). At the very bottom are the UEFI
crypto certs which can also be removed.

But if you have gfx_passthrough=1 working without side-loading
the BIOS with the 64KB limitation, there is probably no point in
doing this.

Gordan

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxx
http://lists.xen.org/xen-users


 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.