Re: Query regarding builnig Xen on Raspberry-Pi3

[siddhartha v <siddhuvgowda.18695@xxxxxxxxx>]

ok sir,

For building should I use "bitbake xen-image-minimal" command?

On Thu, May 14, 2020 at 2:58 PM Bertrand Marquis <Bertrand.Marquis@xxxxxxx> wrote:

Hi,

On 14 May 2020, at 10:24, siddhartha v <siddhuvgowda.18695@xxxxxxxxx> wrote:

Hi sir, 

  I tried to build by adding the line that you suggested but I got below error:

siddhu@siddhu:~/Documents/yocto/build$ bitbake core-image-base
ERROR: Unable to start bitbake server (None)
ERROR: Server log for this session (/home/siddhu/Documents/yocto/build/bitbake-cookerdaemon.log):
--- Starting bitbake server pid 26317 at 2020-05-14 14:52:35.773040 ---
ERROR: ParseError at /home/siddhu/Documents/yocto/build/conf/local.conf:43: unparsed line: 'DISTRO_FEATURES += “virtualization xen”'
siddhu@siddhu:~/Documents/yocto/build$ 

You must have some wrong comas in the line.

Please try to rewrite it.

Bertrand

On Thu, May 14, 2020 at 1:17 PM Bertrand Marquis <Bertrand.Marquis@xxxxxxx> wrote:

> On 14 May 2020, at 08:16, siddhartha v <siddhuvgowda.18695@xxxxxxxxx> wrote:
>
> Hello,
>
>        I am trying to build the Xen to my Raspberry pi3 board. Below is the details,
> BBlayers.conf file:
>
> # POKY_BBLAYERS_CONF_VERSION is increased each time build/conf/bblayers.conf
> # changes incompatibly
> POKY_BBLAYERS_CONF_VERSION = "2"
>
> BBPATH = "${TOPDIR}"
> BBFILES ?= ""
>
> BBLAYERS ?= " \
>   /home/siddhu/Documents/yocto/sources/poky/meta \
>   /home/siddhu/Documents/yocto/sources/poky/meta-poky \
>   /home/siddhu/Documents/yocto/sources/poky/meta-yocto-bsp \
>   /home/siddhu/Documents/yocto/sources/meta-openembedded/meta-oe \
>   /home/siddhu/Documents/yocto/sources/meta-openembedded/meta-multimedia \
>   /home/siddhu/Documents/yocto/sources/meta-openembedded/meta-python \
>   /home/siddhu/Documents/yocto/sources/meta-openembedded/meta-networking \
>   /home/siddhu/Documents/yocto/sources/meta-openembedded/meta-filesystems \
>   /home/siddhu/Documents/yocto/sources/meta-cloud-services \
>   /home/siddhu/Documents/yocto/sources/meta-selinux \
>   /home/siddhu/Documents/yocto/sources/meta-virtualization\
>   /home/siddhu/Documents/yocto/sources/meta-raspberrypi \
>   "
>
> The build went well but after writing to SD card. I typed "$: xl info " but I got " xl not found" error. May I know what mistake I am doing here please.
>
>
> I have attached the local.conf too where I have enabled the virtualisation after going through the readme of the meta-virtualisation.

To activate Xen build you need to add to your local.conf:

DISTRO_FEATURES += “virtualization xen”

You have something to add virtualization but not xen

Then you must start Xen which should start Linux, in your current system you have more then probably just started the Linux generated but Xen needs to be started first and then Xen is starting Linux.

Once you have done that, it would also help if you provide your boot logs.

Regards
Bertrand

> --
> Thanks and Regards.
> Siddhartha V.
> 
> <local.conf>

--

Thanks and Regards.

Siddhartha V.

 

--

Thanks and Regards.

Siddhartha V.