[Xen-changelog] [xen-unstable] IOMMU VTD BUG: disable Extended Interrupt Mode when disabling Interrupt Remapping

[Xen patchbot-unstable <patchbot@xxxxxxx>]

# HG changeset patch
# User Andrew Cooper <andrew.cooper3@xxxxxxxxxx>
# Date 1308053049 -3600
# Node ID 337520d94cba906e64dbd3089d65cda8cf97d1d0
# Parent  d04608ad70f8d119a4e06114b1819880af7c51c3
IOMMU VTD BUG: disable Extended Interrupt Mode when disabling Interrupt 
Remapping

Experimental evidence shows that Extended Interrupt Mode remains in
effect even after Interrupt Remapping is disabled in each DMAR Global
Command Register.  A consiquence of this is that when we switch from
x2apic mode back to xapic mode, and disable interrupt remapping for
the kdump kernel, interrupts passing through the IO APICs are in
x2apic format as opposed xapic.  This causes a triple fault in the
kexec kernel.

As EIM is explicitly set up each time Interrup Remapping is enabled,
it is safe for us to clobber this when taring down.

Also, change the header definition of IRTA_REG_EIME_SHIFT.  It caused
verbose and error-prone code, and was only used in 1 place before.  We
now have IRTA_EIME which is the specific bit in the register.

Signed-off-by: Andrew Cooper <andrew.cooper3@xxxxxxxxxx>
---


diff -r d04608ad70f8 -r 337520d94cba xen/drivers/passthrough/vtd/intremap.c
--- a/xen/drivers/passthrough/vtd/intremap.c    Tue Jun 14 13:02:00 2011 +0100
+++ b/xen/drivers/passthrough/vtd/intremap.c    Tue Jun 14 13:04:09 2011 +0100
@@ -776,8 +776,7 @@
 
 #ifdef CONFIG_X86
     /* set extended interrupt mode bit */
-    ir_ctrl->iremap_maddr |=
-            eim ? (1 << IRTA_REG_EIME_SHIFT) : 0;
+    ir_ctrl->iremap_maddr |= eim ? IRTA_EIME : 0;
 #endif
     spin_lock_irqsave(&iommu->register_lock, flags);
 
@@ -817,6 +816,22 @@
     if ( !ecap_intr_remap(iommu->ecap) )
         return;
 
+    /* If we are disabling Interrupt Remapping, make sure we dont stay in
+     * Extended Interrupt Mode, as this is unaffected by the Interrupt 
+     * Remapping flag in each DMAR Global Control Register.
+     * Specifically, local apics in xapic mode do not like interrupts delivered
+     * in x2apic mode.  Any code turning interrupt remapping back on will set
+     * EIME back correctly.
+     */
+    if ( iommu_supports_eim() )
+    {
+        u64 irta;
+        irta = dmar_readl(iommu->reg, DMAR_IRTA_REG);
+        dmar_writel(iommu->reg, DMAR_IRTA_REG, irta & ~IRTA_EIME);
+        IOMMU_WAIT_OP(iommu, DMAR_IRTA_REG, dmar_readl,
+                      !(irta & IRTA_EIME), irta);
+    }
+
     spin_lock_irqsave(&iommu->register_lock, flags);
     sts = dmar_readl(iommu->reg, DMAR_GSTS_REG);
     if ( !(sts & DMA_GSTS_IRES) )
diff -r d04608ad70f8 -r 337520d94cba xen/drivers/passthrough/vtd/iommu.h
--- a/xen/drivers/passthrough/vtd/iommu.h       Tue Jun 14 13:02:00 2011 +0100
+++ b/xen/drivers/passthrough/vtd/iommu.h       Tue Jun 14 13:04:09 2011 +0100
@@ -471,7 +471,7 @@
 
 #define IEC_GLOBAL_INVL         0
 #define IEC_INDEX_INVL          1
-#define IRTA_REG_EIME_SHIFT     11
+#define IRTA_EIME               (1 << 11)
 
 /* 2^(IRTA_REG_TABLE_SIZE + 1) = IREMAP_ENTRY_NR */
 #define IRTA_REG_TABLE_SIZE     ( IREMAP_PAGE_ORDER + 7 )

_______________________________________________
Xen-changelog mailing list
Xen-changelog@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-changelog