[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-devel] apci issue



On Thu, Apr 21, 2005 at 02:15:06PM +0100, Ian Pratt wrote:
> 
> > Updated to current bk today, and my machine stopped booting ...
> > I've tracked it down to the apic changes from end of last week.
> > cset 1.1307 boots fine, 1.1308 doesn't.
> 
> Gerd: it might be useful to have a log of native 2.6.10/11 booting on
> this machine.

Here we go.

  Gerd

Linux version 2.6.11.4-20a-default (geeko@buildhost) (gcc version 3.3.5 
20050117 (prerelease) (SUSE Linux)) #1 Wed Mar 23 21:52:37 UTC 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
 BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003fffc000 (usable)
 BIOS-e820: 000000003fffc000 - 000000003ffff000 (ACPI data)
 BIOS-e820: 000000003ffff000 - 0000000040000000 (ACPI NVS)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
On node 0 totalpages: 262140
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 225280 pages, LIFO batch:16
  HighMem zone: 32764 pages, LIFO batch:7
DMI 2.3 present.
ACPI: RSDP (v000 ASUS                                  ) @ 0x000f5a60
ACPI: RSDT (v001 ASUS   P3B_F    0x30303031 MSFT 0x31313031) @ 0x3fffc000
ACPI: FADT (v001 ASUS   P3B_F    0x30303031 MSFT 0x31313031) @ 0x3fffc080
ACPI: BOOT (v001 ASUS   P3B_F    0x30303031 MSFT 0x31313031) @ 0x3fffc040
ACPI: DSDT (v001   ASUS P3B_F    0x00001000 MSFT 0x0100000b) @ 0x00000000
ACPI: PM-Timer IO Port: 0xe408
ACPI: local apic disabled
Allocating PCI resources starting at 40000000 (gap: 40000000:bfff0000)
Built 1 zonelists
Kernel command line: root=/dev/hda6 vga=0x317 selinux=0 splash=natine showopts
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 451.074 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1034376k/1048560k available (1865k kernel code, 13484k reserved, 659k 
data, 204k init, 131056k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 894.97 BogoMIPS (lpj=447488)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 
00000000 00000000
CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 
00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel Pentium III (Katmai) stepping 03
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 1312k freed
ACPI: Looking for DSDT in initrd... not found!
 not found!
ACPI: setting ELCR to 0200 (from 0e20)
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf08c0, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
TC classifier action (bugs to netdev@xxxxxxxxxxx cc hadi@xxxxxxxxxx)
pnp: 00:02: ioport range 0xe400-0xe43f could not be reserved
pnp: 00:02: ioport range 0xe800-0xe80f has been reserved
Simple Boot Flag at 0x3a set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1114091641.466:0): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
Limiting direct PCI/PCI transfers.
vesafb: framebuffer at 0xcf000000, mapped to 0xf8880000, using 6144k, total 
8192k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: protected mode interface info at c000:7aa0
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 8 devices)
mice: PS/2 mouse device common for all mice
input: PC Speaker
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
PM: Checking swsusp image.
PM: Resume from disk failed.
ACPI wakeup devices: 
PCI0 UAR1 UAR2 PS2K PS2M USB0 
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 204k freed
input: AT Translated Set 2 keyboard on isa0060/serio0
input: PS/2 Generic Mouse on isa0060/serio1
SCSI subsystem initialized
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 0000:00:04.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: IBM-DTLA-305040, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-ST DVDRAM GSA-4040B, ATAPI CD/DVD-ROM drive
hdd: LG CD-RW CED-8080B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI interrupt 0000:00:0e.0[A] -> GSI 5 (level, low) -> IRQ 5
sym0: <810a> rev 0x12 at pci 0000:00:0e.0 irq 5
sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.1.18n
  Vendor: IBM       Model: DCAS-34330        Rev: S65A
  Type:   Direct-Access                      ANSI SCSI revision: 02
sym0:0:0: tagged command queuing enabled, command queue depth 16.
 target0:0:0: Beginning Domain Validation
 target0:0:0: Domain Validation skipping write tests
sym0:0: FAST-10 SCSI 10.0 MB/s ST (100.0 ns, offset 8)
 target0:0:0: Ending Domain Validation
SCSI device sda: 8467200 512-byte hdwr sectors (4335 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 8467200 512-byte hdwr sectors (4335 MB)
SCSI device sda: drive cache: write back
 sda: unknown partition table
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
hda: max request size: 128KiB
hda: 80418240 sectors (41174 MB) w/380KiB Cache, CHS=65535/16/63, UDMA(33)
hda: cache flushes not supported
 hda: hda1 hda2 < hda5 hda6 hda7 > hda4
 hda4: <bsd: hda8 hda9 hda10 >
hdc: ATAPI 32X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache, DMA
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
JBD: barrier-based sync failed on hda6 - disabling barriers
Adding 1052216k swap on /dev/hda5.  Priority:42 extents:1
JBD: barrier-based sync failed on hda6 - disabling barriers
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 
[PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@xxxxxxxxxx
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 440BX Chipset.
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 256M @ 0xd0000000
piix4_smbus 0000:00:04.3: Found 0000:00:04.3 device
Linux Tulip driver version 1.1.13-NAPI (May 11, 2002)
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 11 (level, low) -> IRQ 11
tulip0:  MII transceiver #1 config 3000 status 7829 advertising 01e1.
eth0: Lite-On 82c168 PNIC rev 32 at 0001b800, 00:A0:CC:55:9B:F9, IRQ 11.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
cdrom: open failed.
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI interrupt 0000:00:04.2[D] -> GSI 9 (level, low) -> IRQ 9
uhci_hcd 0000:00:04.2: UHCI Host Controller
uhci_hcd 0000:00:04.2: irq 9, io base 0xd400
uhci_hcd 0000:00:04.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ufs_read_super: fs is active
ufs_read_super: fs is active
st: Version 20041025, fixed bufsize 32768, s/g segs 256
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
cdrom: open failed.
cdrom: open failed.
atm: unsupported module, tainting kernel.
NET: Registered protocol family 8
NET: Registered protocol family 20
Bridge firewalling registered
device hw0 entered promiscuous mode
hw0: Promiscuous mode enabled.
hw0: Promiscuous mode enabled.
eth0: port 1(hw0) entering learning state
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>
device uml0 entered promiscuous mode
eth0: port 2(uml0) entering learning state
Linux video capture interface: v1.00
saa7130/34: v4l2 driver version 0.2.12 loaded
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 9 (level, low) -> IRQ 9
saa7134[0]: quirk: PCIPCI_NATOMA
saa7134[0]: found at 0000:00:09.0, rev: 1, irq: 9, latency: 32, mmio: 0xc6000000
saa7134[0]: subsystem: ffff:ffff, board: KNC One TV-Station RDS / Typhoon TV 
Tuner RDS [card=7,insmod option]
saa7134[0]: board init: gpio is 410320
saa7134[0]: i2c eeprom 00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tuner: chip found at addr 0xc0 i2c-bus saa7134[0]
tuner: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) by saa7134[0]
tda9885/6/7: chip found @ 0x86
hw0: Setting full-duplex based on MII#1 link partner capability of cde1.
saa7134[0]: registered device video0 [v4l2]
saa7134[0]: registered device vbi0
saa7134[0]: registered device radio0
saa7146: register extension 'budget_ci dvb'.
ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 9 (level, low) -> IRQ 9
saa7146: found saa7146 @ mem f8fe8000 (revision 1, irq 9) (0x13c2,0x1011).
DVB: registering new adapter (TT-Budget/WinTV-NOVA-T  PCI).
adapter has MAC addr = 00:d0:5c:22:1a:19
DVB: registering frontend 0 (Philips TDA10045H DVB-T)...
saa7134[0]/audio: audio carrier scan failed, using 5.500 MHz [default]
eth0: topology change detected, propagating
eth0: port 1(hw0) entering forwarding state
NET: Registered protocol family 17
eth0: topology change detected, propagating
eth0: port 2(uml0) entering forwarding state
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 10 (level, low) -> IRQ 10
NET: Registered protocol family 10
Disabled Privacy Extensions on device c033d600(lo)
hw0: Promiscuous mode enabled.
hw0: Promiscuous mode enabled.
IPv6 over IPv4 tunneling driver
Disabled Privacy Extensions on device f7edd800(sit0)
load_module: err 0xffffffef (dont worry)
ACPI: Power Button (FF) [PWRF]
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
powernow: This module only works with AMD K7 CPUs
hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hda: drive_cmd: error=0x04 { DriveStatusError }
ide: failed opcode was: 0xef
sym0: SCSI parity error detected: SCR1=132 DBC=50000000 SBCL=0
eth0: no IPv6 routers present
hw0: no IPv6 routers present
uml0: no IPv6 routers present
JBD: barrier-based sync failed on hda7 - disabling barriers

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel


 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.