RE: [Xen-users] xen 3.0 boot problem

[Githogori Nyangara-Murage <githogori@xxxxxxxxxxxxx>]

As I had stated earlier, I have again built Xen-unstable and have it
running on a Dell 1850 which has a qla2300 card. In fact right now it is
busy beating up on the storage using ibre channel via the qla2300. It is
on RHEL 4.1, and build against a vanilla Cambridge download, so this
should also work on SuSE.

Below is a snippet of my messages file.

 .githogori.

Oct  6 22:19:58 localhost kernel: Red Hat/Adaptec aacraid driver
(1.1.2-lk2 Oct  6 2005)
Oct  6 22:19:58 localhost kernel: QLogic Fibre Channel HBA Driver
Oct  6 22:19:58 localhost kernel: ACPI: PCI Interrupt 0000:02:0b.0[A] ->
GSI 37 (level, low) -> IRQ 37
Oct  6 22:19:58 localhost kernel: qla2300 0000:02:0b.0: Found an
ISP2312, irq 37, iobase 0xe0002000
Oct  6 22:19:58 localhost kernel: scsi0 : qla2xxx
Oct  6 22:19:58 localhost kernel: qla2300 0000:02:0b.0: Configuring PCI
space...
Oct  6 22:19:58 localhost kernel: qla2300 0000:02:0b.0: Configure NVRAM
parameters...
Oct  6 22:19:58 localhost kernel: qla2300 0000:02:0b.0: Verifying loaded
RISC code...
Oct  6 22:19:58 localhost kernel: qla2300 0000:02:0b.0: Waiting for LIP
to complete...
Oct  6 22:19:58 localhost kernel: qla2300 0000:02:0b.0: Cable is
unplugged...
Oct  6 22:19:58 localhost kernel: qla2300 0000:02:0b.0:
Oct  6 22:19:58 localhost kernel:  QLogic Fibre Channel HBA Driver:
8.00.02b5-k
Oct  6 22:19:58 localhost kernel:   QLogic QLA2342 - 133MHz PCI-X to 2Gb
FC, Dual Channel
Oct  6 22:19:58 localhost kernel:   ISP2312: PCI-X (133 MHz) @
0000:02:0b.0 hdma-, host#=0, fw=3.03.08 IPX
Oct  6 22:19:58 localhost kernel: ACPI: PCI Interrupt 0000:02:0b.1[B] ->
GSI 38 (level, low) -> IRQ 38
Oct  6 22:19:58 localhost kernel: qla2300 0000:02:0b.1: Found an
ISP2312, irq 38, iobase 0xe0004000
Oct  6 22:19:59 localhost kernel: scsi1 : qla2xxx
Oct  6 22:19:59 localhost kernel: qla2300 0000:02:0b.1: Configuring PCI
space...
Oct  6 22:19:59 localhost kernel: qla2300 0000:02:0b.1: Configure NVRAM
parameters...
Oct  6 22:19:59 localhost kernel: qla2300 0000:02:0b.1: Verifying loaded
RISC code...
Oct  6 22:19:59 localhost kernel: qla2300 0000:02:0b.1: Waiting for LIP
to complete...
Oct  6 22:19:59 localhost kernel: qla2300 0000:02:0b.1: LIP reset
occured (f8f7).
Oct  6 22:19:59 localhost kernel: qla2300 0000:02:0b.1: LIP occured
(f8f7).
Oct  6 22:19:59 localhost kernel: qla2300 0000:02:0b.1: LOOP UP detected
(1 Gbps).
Oct  6 22:19:59 localhost kernel: qla2300 0000:02:0b.1: Topology -
(Loop), Host Loop address 0x7d
Oct  6 22:19:59 localhost kernel: qla2300 0000:02:0b.1:
Oct  6 22:19:59 localhost kernel:  QLogic Fibre Channel HBA Driver:
8.00.02b5-k
Oct  6 22:19:59 localhost kernel:   QLogic QLA2342 - 133MHz PCI-X to 2Gb
FC, Dual Channel
Oct  6 22:19:59 localhost kernel:   ISP2312: PCI-X (133 MHz) @
0000:02:0b.1 hdma-, host#=1, fw=3.03.08 IPX
Oct  6 22:19:59 localhost kernel: megaraid cmm: 2.20.2.5 (Release Date:
Fri Jan 21 00:01:03 EST 2005)
Oct  6 22:19:59 localhost kernel: megaraid: 2.20.4.5 (Release Date: Thu
Feb 03 12:27:22 EST 2005)
Oct  6 22:19:59 localhost kernel:   Vendor: DGC       Model: RAID 5
Rev: 0411
Oct  6 22:19:59 localhost kernel:   Type:   Direct-Access
ANSI SCSI revision: 02
Oct  6 22:19:59 localhost kernel: 3ware Storage Controller device driver
for Linux v1.26.02.001.
Oct  6 22:19:59 localhost kernel: SCSI device sda: 68317440 512-byte
hdwr sectors (34979 MB)


On Wed, 2005-10-05 at 21:28 +0100, Ian Pratt wrote:
>  Has anyone used xen succefully with a qla2300?
> 
> What machines have this card?
> 
> Ian
> 
> > I've installed Xen 3.0-devel on SUSE Linux without any problems.
> > But when i tryed to boot the system, i've got a funny problem:
> > 
> > qla2300 0000:05:01.0: Found an ISP2312, irq 185, iobase 
> > 0xf8812000 qla2300 0000:05:01.0: Configuring PCI space...
> > qla2300 0000:05:01.0: Configure NVRAM parameters...
> > qla2300 0000:05:01.0: Verifying loaded RISC code...
> > qla2300 0000:05:01.0: Waiting for LIP to complete...
> > 
> > until here all works fine, but then:
> > 
> > input: PS/2 Generic Mouse on synaptcs-pt/serio0 qla2300 
> > 0000:05:01.0: LIP reset occured (f7f7).
> > qla2300 0000:05:01.0: LOOP UP detected (2 Gbps).
> > qla2300 0000:05:01.0: Topology - (F_Port), Host Loop address 0xffff
> > scsi3 : qla2xxx
> > qla2300 0000:04:02.0:
> >   QLogic Fibre Channel HBA Driver: 8.01.00b5-k
> >   QLogic QLA2340 - 133MHz PCI-X to 2Gb FC, Single Channel
> >   ISP2312: PCI-X (100 MHz) @ 0000:05:01.0 hdma+, host#=3,
> > fw=3.03.15 IPX
> > Loading kernel/fs/reiserfs/reiserfs.ko
> > Waiting for device /dev/sda4 to appear: .....not found --- 
> > exiting to /bin/sh $
> > 
> > if i use the standard (bigsmp) kernel the normal massages are:
> > 
> > SCSI device sda: 41943040 512-byte hdwr sectors (21475 MB) 
> > SCSI device sda: drive cache: write back SCSI device sda: 
> > 41943040 512-byte hdwr sectors (21475 MB) SCSI device sda: 
> > drive cache: write back
> >  sda: sda1 sda2 sda3 sda4
> > ....usw.
> > 
> > Well, my qla2300 has the storage attached not a generic mouse.
> > Of course it isn't possible to boot from this mouse. :-(
> 
> 
> 
> _______________________________________________
> Xen-users mailing list
> Xen-users@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-users

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users