[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] [Xen-devel] qla2xxx driver failed in dom0 - invalid opcode: 0000 [1] SMP
I wanted to post this in case there is a real bug here. The system this is on is running Debian Etch with the Xen packages from Debian Unstable (currently 3.0.2+hg9697-1). I am running all packaged software so this is probably slightly out of date. This is on an HP DL320 G4 with a Pentium D 930 processor. I tried unloading and reloading the qla2xxx module, but rmmod reported it in use, however it did not seem to be used by any other module. dmesg output below: QLogic Fibre Channel HBA Driver qla2xxx 0000:06:01.0: Found an ISP2312, irq 16, iobase 0xffffc2000001e000 qla2xxx 0000:06:01.0: Configuring PCI space... qla2xxx 0000:06:01.0: Configure NVRAM parameters... ----------- [cut here ] --------- [please bite here ] --------- Kernel BUG at arch/x86_64/mm/fault-xen.c:292 invalid opcode: 0000 [1] SMP CPU 1 Modules linked in: qla2xxx libata firmware_class tg3 scsi_transport_fc psmouse serio_raw serial_core ext3 jbd mbcache cciss scsi_mod Pid: 2163, comm: modprobe Not tainted 2.6.16-2-xen-em64t-p4 #1 RIP: e030:[<ffffffff801166f7>] <ffffffff801166f7>{do_page_fault+1656} RSP: e02b:ffff88000ec1daf8 EFLAGS: 00010287 RAX: ffff800000000000 RBX: ffff880000c6a000 RCX: 00003ffffffff000 RDX: 00000000000fdff0 RSI: ffff880000c690f0 RDI: 0000000000010800 RBP: ffff880000000000 R08: 0000000000010800 R09: 0000000000000000 R10: 0000000003c69067 R11: ffff880001000000 R12: ffffc2000001e00e R13: ffff88000ec1dbe8 R14: ffff88000e2cf140 R15: 0000000000000002 FS: 00002ad5ad5566d0(0000) GS:ffffffff80407080(0000) knlGS:0000000000000000 CS: e033 DS: 0000 ES: 0000 Process modprobe (pid: 2163, threadinfo ffff88000ec1c000, task ffff88000e2cf140) Stack: ffffffffffffd028 ffff880000c6b000 0000000000002fd8 0000000000030001 0000000000000246 ffffffff801e7166 000000000000001e 0000000000000034 0000000000030000 ffffffff8010722a Call Trace: <ffffffff801e7166>{vgacon_cursor+0} <ffffffff8010722a>{hypercall_page+554} <ffffffff8010722a>{hypercall_page+554} <ffffffff8023729f>{force_evtchn_callback+10} <ffffffff8010b403>{error_exit+0} <ffffffff801e03d4>{__pci_find_next_cap+100} <ffffffff801e03d4>{__pci_find_next_cap+100} <ffffffff880d7a5f>{:qla2xxx:qla2x00_get_nvram_word+72} <ffffffff880d7a97>{:qla2xxx:qla2x00_get_nvram_word+128} <ffffffff801e03d4>{__pci_find_next_cap+100} <ffffffff880d7ae5>{:qla2xxx:qla2x00_read_nvram_data+41} <ffffffff880ca5e3>{:qla2xxx:qla2x00_nvram_config+137} <ffffffff880cd48f>{:qla2xxx:qla2x00_initialize_adapter+243} <ffffffff880c83cd>{:qla2xxx:qla2x00_probe_one+3594} <ffffffff80121dc0>{__wake_up+54} <ffffffff801e2220>{pci_device_probe+74} <ffffffff802334a1>{driver_probe_device+82} <ffffffff80233550>{__driver_attach+0} <ffffffff802335a6>{__driver_attach+86} <ffffffff80232ae4>{bus_for_each_dev+67} <ffffffff80232ddd>{bus_add_driver+110} <ffffffff801e7166>{vgacon_cursor+0} <ffffffff801e1e2a>{__pci_register_driver+128} <ffffffff88078e5b>{:scsi_transport_fc:fc_attach_transport+216} <ffffffff880e908f>{:qla2xxx:qla2x00_module_init+143} <ffffffff80142b2e>{sys_init_module+240} <ffffffff8010acea>{system_call+134} <ffffffff8010ac64>{system_call+0} Code: 0f 0b 68 aa 8f 2e 80 c2 24 01 e9 59 04 00 00 41 f6 c7 08 74 RIP <ffffffff801166f7>{do_page_fault+1656} RSP <ffff88000ec1daf8> A soft reboot from the dom0 produced a successful load the second time: QLogic Fibre Channel HBA Driver qla2xxx 0000:06:01.0: Found an ISP2312, irq 16, iobase 0xffffc2000001e000 qla2xxx 0000:06:01.0: Configuring PCI space... qla2xxx 0000:06:01.0: Configure NVRAM parameters... qla2xxx 0000:06:01.0: Verifying loaded RISC code... qla2xxx 0000:06:01.0: Waiting for LIP to complete... qla2xxx 0000:06:01.0: LIP reset occured (f700). qla2xxx 0000:06:01.0: LOOP UP detected (2 Gbps). qla2xxx 0000:06:01.0: Topology - (F_Port), Host Loop address 0xffff scsi0 : qla2xxx qla2xxx 0000:06:01.0: QLogic Fibre Channel HBA Driver: 8.01.04-k QLogic QLA2340 - ISP2312: PCI-X (133 MHz) @ 0000:06:01.0 hdma-, host#=0, fw=3.03.20 IPX scsi: unknown device type 12 Vendor: COMPAQ Model: MSA1000 Rev: 5.02 Type: RAID ANSI SCSI revision: 04 Vendor: COMPAQ Model: MSA1000 VOLUME Rev: 5.02 Type: Direct-Access ANSI SCSI revision: 04 Vendor: COMPAQ Model: MSA1000 VOLUME Rev: 5.02 Type: Direct-Access ANSI SCSI revision: 04 -- Michael Brancato, CISSP, CCNA _______________________________________________ Xen-devel mailing list Xen-devel@xxxxxxxxxxxxxxxxxxx http://lists.xensource.com/xen-devel
|
Lists.xenproject.org is hosted with RackSpace, monitoring our |