[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: [Xen-devel] [PATCH 0/2] Improve hpet accuracy



Dan,

You shouldn't be getting higher than .05%.
I'd like to figure out what is wrong. I'm running the same guest
you are with heavy loads and the physical processors overcommitted
by 3:1. And I'm seeing .027% error on rh5u1-64 after an hour.

Can you type ^a^a^a at the console and then
type 'Z' a couple of times about 10 seconds apart and send
me the output? Do this when you have a domain
running that is keeping poor time.

You should take drift measurements over a period
of time that is at least 20 minutes, preferably longer.

Also, can you send me a tarball of your sources from
the xen directory?


thanks,
Dave




-----Original Message-----
From: Dan Magenheimer [mailto:dan.magenheimer@xxxxxxxxxx]
Sent: Thu 6/12/2008 6:05 PM
To: Dave Winchell; Keir Fraser; xen-devel
Cc: Ben Guthro
Subject: Re: [Xen-devel] [PATCH 0/2] Improve hpet accuracy

(Going back on list.)

OK, so looking at the updated patch, hpet_avoid=1 is actually
working, just reporting wrong, correct?

With el5u1-64-hvm and hpet_avoid=1 and timer_mode=4, skew
is under -0.04% and falling.  With hpet_avoid=0, it looks
about the same.  However both cases seem to start creeping
up again when I put load on, then fall again when I remove
the load -- even with sched-credit capping cpu usage.  Odd!
This implies to me that the activity in the other domains
IS affecting skew on the domain-under-test. (Keir, any
comments on the hypothesis attached below?)

Another theoretical oddity... if you are always delivering
timer ticks "late", fewer than the nominal 1000 ticks/sec
should be being received.  So then why is guest time actually
going faster than an external source?

(In my mind, going faster is much worse than going slower
because if ntpd or a human moves time backwards to compensate
for a clock going faster, "make" and other programs can
get very confused.)

Dan

> -----Original Message-----
> From: Dan Magenheimer [mailto:dan.magenheimer@xxxxxxxxxx]
> Sent: Thursday, June 12, 2008 3:13 PM
> To: 'Dave Winchell'
> Subject: RE: xen hpet patch
>
>
> One more thought while waiting for compile and reboot:
>
> Am I right that all of the policies are correcting for when
> a domain "A" is out-of-context?  There's nothing in any other
> domain "B" that can account for any timer loss/gain in domain
> "A".  The only reason we are running other domains is to ensure
> that domain "A" is sometimes out-of-context, and the more
> it is out-of-context, the more likely we will observe
> a problem, correct?
>
> If this is true, it doesn't matter what workload is run
> in the non-A domains... as long as it is loading the
> CPU(s), thus ensuring that domain A is sometimes not
> scheduled on any CPU.
>
> And if all this is true, we may not need to run other
> domains at all... running "xm sched-credit -d A -c 50"
> should result in domain A being out-of-context at least
> half the time.

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel

 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.