[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Xen-devel] megaraid sas driver failing in Xen-3.4 unstable version


  • To: "xen-devel@xxxxxxxxxxxxxxxxxxx" <xen-devel@xxxxxxxxxxxxxxxxxxx>
  • From: "Manyam, Ramesh" <Ramesh.Manyam@xxxxxxx>
  • Date: Wed, 19 Nov 2008 19:45:35 +0530
  • Accept-language: en-US
  • Acceptlanguage: en-US
  • Delivery-date: Wed, 19 Nov 2008 06:16:14 -0800
  • List-id: Xen developer discussion <xen-devel.lists.xensource.com>
  • Thread-index: AclKUUqAqjX7sXkZQo2R2NdSe87UjA==
  • Thread-topic: megaraid sas driver failing in Xen-3.4 unstable version

 

On Xen-3.4 (unstable version), I have created CentOS HVM guest & WS2K8 HVM guest and dedicated MegaRAID SAS controller but I am not able to see the disk which is connected to MegaRAID SAS controller when I do fdisk l (vtd support is enabled in Xen).

 

Looks like the pci device(MegaRAID SAS controller) is getting dedicated successfully as I can see the device in the list of pci devices shown by lspci(on CentOS HVM).

 

00:06.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS

 

 

However the driver is not getting attached properly and fails with the following error

 

=======================================================================================

“dmesg” of HVM CentOS

megasas: Failed to init firmware

ACPI: PCI interrupt for device 0000:00:06.0 disabled

 

 

“/var/log/messages”

pciback 0000:02:0e.0: seizing device

 PCI: Enabling device 0000:02:0e.0 (0190 -> 0192)

 ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 66 (level, low) -> IRQ 25

 ACPI: PCI interrupt for device 0000:02:0e.0 disabled

=======================================================================================

 

 

 

On WS2K8 HVM, I am able to see MegaRAID SAS controller under “Storage Controllers” on WS2K8 HVM and the status of device is

 

=========================================================================================================================================================

This device cannot start.(Code 10)

Description:

 Windows was able to successfully install device driver software, but the driver software encountered a problem when it tried to run. The problem code is   

 10.

Problem Signature:

 Problem Event Name:PnPDeviceProblemCode

 Architecture: x86

 Hardware Id: PCI\VEN_1000&DEV_0411&SUBSYS_10081000&REV_00

 Setup class GUID: {4d36e97b-e325-11ce-bfc1-08002be10318}

 PnP problem code: 0000000A

 Driver name: megasas.sys

 Driver version: 2.13.0.32

 Driver date: 01-19-2008

 OS Version: 6.0.6001.2.1.0.272.7

 Locale ID: 1033

 ========================================================================================================================================================

And also I am not able to see the disk which is connected to MegaRAID SAS controller

 

============================================================================

“/var/log/messages”

pciback 0000:02:0e.0: seizing device

PCI: Enabling device 0000:02:0e.0 (0190 -> 0192)

ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 66 (level, low) -> IRQ 25

ACPI: PCI interrupt for device 0000:02:0e.0 disabled

============================================================================

 

 

Any clues ?

 

Thanks,

Ramesh

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel

 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.