[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-devel] Xen Paravirt Operations Domain 0 Serial Console Problem



Hi

When I boot up the computer using onboard Intel GMA 4500 as the primary VGA controller, I could still see the NVIDIA Geforce 8400 GS PCI Express x16 card in lspci.

00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03)
01:00.0 VGA compatible controller: nVidia Corporation GeForce 8400 GS (rev a1)


-- 
Mr. Teo En Ming (Zhang Enming) Dip(Mechatronics Engineering) BEng(Hons)(Mechanical Engineering) 
Technical Support Engineer 
Information Technology Department
Asiasoft Online Pte Ltd
Tampines Central 1 #04-01 Tampines Plaza 
Singapore 529541
Republic of Singapore
Mobile: +65-9648-9798
MSN: teoenming@xxxxxxxxxxx
Alma Maters: Singapore Polytechnic, National University of Singapore


On 08/25/2009 03:35 AM, Mr. Teo En Ming (Zhang Enming) wrote:
I have already compiled CONFIG_PCI_STUB=y statically into the kernel.

-- 
Mr. Teo En Ming (Zhang Enming) Dip(Mechatronics Engineering) BEng(Hons)(Mechanical Engineering) 
Technical Support Engineer 
Information Technology Department
Asiasoft Online Pte Ltd
Tampines Central 1 #04-01 Tampines Plaza 
Singapore 529541
Republic of Singapore
Mobile: +65-9648-9798
MSN: teoenming@xxxxxxxxxxx
Alma Maters: Singapore Polytechnic, National University of Singapore


On 08/25/2009 03:33 AM, Mr. Teo En Ming (Zhang Enming) wrote:
I find that following the instructions here at Xen Wiki VtdHowTo don't work:

Binding Devices to pci-stub

If using pv-ops dom0, also can use pci-stub to hide devices for assignment (example PCI device 01:00.0) * lspci -n * locate the entry for device 01:00.0 and note down the vendor & device ID 8086:10b9 .

...
01:00.0 0200: 8086:10b9 (rev 06)
...

* then use following commands to hide it: .

echo "8086 10b9" > /sys/bus/pci/drivers/pci-stub/new_id
echo "0000:01:00.0" > /sys/bus/pci/devices/0000:01:00.0/driver/unbind
echo "0000:01:00.0" > /sys/bus/pci/drivers/pci-stub/bind

When I tried to "cat /sys/bus/pci/drivers/pci-stub/new_id", it says permission denied.

My NVIDIA graphics card is using BDF 01:00.0. When I change directory to 
/sys/bus/pci/devices/0000:01:00.0/, sub-directory driver is not found at all.

Then when I put in pci = [ '01:00.0' ] for the Windows XP Home HVM config, it complains about pciback but I am using paravirt-ops dom 0 kernel.

And when I tried the "xm pci-list-assignable-devices", nothing shows up.

I have already specified iommu=1 in grub.

Hope the Intel folks can assist in this matter.


-- 
Mr. Teo En Ming (Zhang Enming) Dip(Mechatronics Engineering) BEng(Hons)(Mechanical Engineering) 
Technical Support Engineer 
Information Technology Department
Asiasoft Online Pte Ltd
Tampines Central 1 #04-01 Tampines Plaza 
Singapore 529541
Republic of Singapore
Mobile: +65-9648-9798
MSN: teoenming@xxxxxxxxxxx
Alma Maters: Singapore Polytechnic, National University of Singapore


On 08/25/2009 03:23 AM, Mr. Teo En Ming (Zhang Enming) wrote:
I have both the onboard Intel GMA 4500 and the PCI Express x16 NVIDIA Geforce 8400 GS.

Ng Beng Heng at the University of Michigan has done it. He's using the same Intel DQ45CB as me.





_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel

 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.