[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] Re: [Xen-devel] anyone using pvusb?
Hi James, I have tested with current tip. My flash drive worked properly. I found no regression with my environment. The main difference between us is flash drive. In your environment, do other devices become the same error? Or, some devices work? My test environment is as follows. PC: Core 2 Quad Q9450 with Q35+ICH9DO Xen: xen-3.4-testing.hg (c/s 19749) Dom0 OS: CentOS 5.3 Dom0 kernel: linux-2.6.18-xen.hg (c/s 931) DomU OS: CentOS 5.3 Dom0 kernel: linux-2.6.18-xen.hg (c/s 931) Tested Device: Buffalo RUF2-R2GS (VendorID:0411, ProductID:0098) dmesg output on domU: vusb vusb-0: Xen USB2.0 Virtual Host Controller driver (usbfront) drivers/usb/core/inode.c: creating file 'devices' drivers/usb/core/inode.c: creating file '001' vusb vusb-0: new USB bus registered, assigned bus number 1 usb usb1: default language 0x0409 usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: Xen USB2.0 Virtual Host Controller driver (usbfront) usb usb1: Manufacturer: Linux 2.6.18.8-cs931-domU xen_hcd usb usb1: SerialNumber: vusb-0 usb usb1: uevent usb usb1: configuration #1 chosen from 1 choice usb usb1: adding 1-0:1.0 (config #1, interface 0) usb 1-0:1.0: uevent hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: no power switching (usb 1.0) hub 1-0:1.0: individual port over-current protection hub 1-0:1.0: Single TT hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns) hub 1-0:1.0: power on to power good time: 20ms hub 1-0:1.0: local power source is good hub 1-0:1.0: trying to enable port power on non-switchable hub drivers/usb/core/inode.c: creating file '001' hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000 hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002 hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501 usb 1-1: new high speed USB device using vusb and address 2 usb 1-1: default language 0x0409 usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-1: Product: USB Flash Disk usb 1-1: Manufacturer: BUFFALO usb 1-1: SerialNumber: F215700809250007 usb 1-1: uevent usb 1-1: configuration #1 chosen from 1 choice usb 1-1: adding 1-1:1.0 (config #1, interface 0) usb 1-1:1.0: uevent drivers/usb/core/inode.c: creating file '002' hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002 SCSI subsystem initialized Initializing USB Mass Storage driver... usb-storage 1-1:1.0: usb_probe_interface usb-storage 1-1:1.0: usb_probe_interface - got id scsi0 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning usbcore: registered new driver usb-storage USB Mass Storage support registered. Vendor: BUFFALO Model: USB Flash Disk Rev: 4000 Type: Direct-Access ANSI SCSI revision: 00 usb-storage: device scan complete scsi 0:0:0:0: Attached scsi generic sg0 type 0 SCSI device sda: 3973120 512-byte hdwr sectors (2034 MB) sda: Write Protect is off sda: Mode Sense: 00 00 00 00 sda: assuming drive cache: write through SCSI device sda: 3973120 512-byte hdwr sectors (2034 MB) sda: Write Protect is off sda: Mode Sense: 00 00 00 00 sda: assuming drive cache: write through sda: sda1 sd 0:0:0:0: Attached scsi removable disk sda Regards, Noboru _______________________________________________ Xen-devel mailing list Xen-devel@xxxxxxxxxxxxxxxxxxx http://lists.xensource.com/xen-devel
|
![]() |
Lists.xenproject.org is hosted with RackSpace, monitoring our |