|
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] Re: [Xen-devel] MSI badness in xen-unstable
On Sat, 2010-10-16 at 18:25 +0100, Sander Eikelenboom wrote:
> Probably there are more problems, you could also try a xen-unstable
> from before the commit that changed this code (msi.c)
> Another thing that could make it eassier to debug would be to put some
> printk's around the WARN_ON's in msi.c at the linenumbers that gave
> the warnings, showing but parts of the equation in the WARN_ON
Yes, I am still getting WARN's after the inverted masks patch too.
Bruces patch was line-wrap mangled but I instrumented the WARN that I'm
hitting based on that. The device in question is a broadcom netXtreme II
- there are two installed in the box but only one of them is brought up.
The WARN's happen when the interface is brought up for DHCP.
(XEN) =================================================
(XEN) msi->table_base != read_pci_mem_bar(bus, slot, func, bir)
(XEN) msi->table_base = da000000
(XEN) read_pci_mem_bar = 0
(XEN) bus=2, slot=0, func=0, bir=0
(XEN) =================================================
(XEN) =================================================
(XEN) No pba_addr: bus=2, slot=0, func=0, bir=0
(XEN) =================================================
The problem appears to be as simple as read_pci_mem_bar() returning
zero. This can only happen for a few possible reasons and in my case
what I got was:
pci_conf_read8(bus, slot, func, PCI_HEADER_TYPE) is not one of:
PCI_HEADER_TYPE_NORMAL
PCI_HEADER_TYPE_BRIDGE
PCI_HEADER_TYPE_CARDBUS
Thereby bailing in the switch statement. It seems that the problem here
is that the multi-function bit (0x80) was not being masked out. Does the
following patch work for you guys?
diff -r fc2242ac90e1 xen/arch/x86/msi.c
--- a/xen/arch/x86/msi.c Mon Oct 18 11:31:47 2010 +0100
+++ b/xen/arch/x86/msi.c Mon Oct 18 18:14:22 2010 +0100
@@ -527,7 +527,7 @@ static u64 read_pci_mem_bar(u8 bus, u8 s
u8 limit;
u32 addr;
- switch ( pci_conf_read8(bus, slot, func, PCI_HEADER_TYPE) )
+ switch ( pci_conf_read8(bus, slot, func, PCI_HEADER_TYPE) & 0x7f )
{
case PCI_HEADER_TYPE_NORMAL:
limit = 6;
FYI: This is function 0 of my multi-function bnx2 NIC. I notice your
affected devices were also multi-function
02:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5716 Gigabit
Ethernet (rev 20)
Subsystem: Dell Device 02a3
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at da000000 (64-bit, non-prefetchable) [size=32M]
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: Broadcom NetXtreme II Ethernet Controller
Read-only fields:
[PN] Part number: BCM95716C1
[EC] Engineering changes: 220197-3
[SN] Serial number: 0123456789
[MN] Manufacture ID: 31 30 32 38
[V0] Vendor specific: 5.0.13
[RV] Reserved: checksum good, 22 byte(s) reserved
End
Capabilities: [58] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [a0] MSI-X: Enable+ Count=9 Masked-
Vector table: BAR=0 offset=0000c000
PBA: BAR=0 offset=0000e000
Capabilities: [ac] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <4us, L1
<64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+
Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency
L0 <2us, L1 <2us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Device Serial Number a4-ba-db-ff-fe-4d-11-0b
Capabilities: [110 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt+
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC+ UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [150 v1] Power Budgeting <?>
Capabilities: [160 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Kernel driver in use: bnx2
02:00.1 Ethernet controller: Broadcom Corporation NetXtreme II BCM5716 Gigabit
Ethernet (rev 20)
Subsystem: Dell Device 02a3
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at dc000000 (64-bit, non-prefetchable) [size=32M]
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: Broadcom NetXtreme II Ethernet Controller
Read-only fields:
[PN] Part number: BCM95716C1
[EC] Engineering changes: 220197-3
[SN] Serial number: 0123456789
[MN] Manufacture ID: 31 30 32 38
[V0] Vendor specific: 5.0.13
[RV] Reserved: checksum good, 22 byte(s) reserved
End
Capabilities: [58] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [a0] MSI-X: Enable- Count=9 Masked-
Vector table: BAR=0 offset=0000c000
PBA: BAR=0 offset=0000e000
Capabilities: [ac] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <4us, L1
<64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+
Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency
L0 <2us, L1 <2us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Device Serial Number a4-ba-db-ff-fe-4d-11-0c
Capabilities: [110 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt+
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC+ UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [150 v1] Power Budgeting <?>
Capabilities: [160 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Kernel driver in use: bnx2
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel
|
 |
Lists.xenproject.org is hosted with RackSpace, monitoring our |