Re: [Xen-devel] xl create doesn't like kernel

[Mike Wright <mike.wright@xxxxxxxxxxxxxx>]

On 07/04/2011 01:54 AM, Ian Campbell wrote:
> On Fri, 2011-07-01 at 20:31 +0100, Mike Wright wrote:
> > Hi all,
> >
> > New to xen-4 and the new tools.
> >
> > Running xen-4.1.1 with linux-3.0.0-rc5.
> >
> > I have a kernel that boots on bare metal that I thought should boot as a
> > domU.
> >
> > This is the command: xl create vm1
> >
> > Here are the first few lines of vm1's config file:
> Please can you provide the whole file please.
Thanks for replying, Ian.

Turns out I'd messed up in a couple of places.  I'd used sda for my 
targets instead of xvda and no 'root =' in the vm's config.
In the vm's /etc/fstab I hadn't adjusted / and /swap to /dev/xvda?, nor 
had I commented out /boot.
After that all was well in virtualization land ;)

> > # Kernel image file.
> > kernel = "/boot/vmlinuz-2.6.35.6-45.fc14.i686"
> >
> > # Optional ramdisk.
> > ramdisk = "/boot/initramfs-2.6.35.6-45.fc14.i686.img"
> Those paths are valid within the dom0 filesystem?
>
> > Here is the error message:
> >
> > Parsing config file vm1
> > xc: error: elf_xen_note_check: ERROR: Will only load images built for
> > the generic loader or Linux images: Invalid kernel
> > libxl: error: libxl_dom.c:196:libxl__build_pv xc_dom_parse_image failed:
> > Success
> > cannot (re-)build domain: -3
> Does "xl -vvv create vm1" give any more information?
>
> I downloaded kernel-PAE-2.6.35.6-45.fc14.i686.rpm from
> http://rpm.pbone.net/index.php3/stat/4/idpl/15471895/dir/fedora_14/com/kernel-PAE-2.6.35.6-45.fc14.i686.rpm.html
>  (actually
> ftp://ftp.sunet.se/pub/Linux/distributions/fedora/linux/releases/14/Everything/i386/os/Packages/kernel-PAE-2.6.35.6-45.fc14.i686.rpm
>  ) which contained /boot/vmlinuz-2.6.35.6-45.fc14.i686.PAE with md5sum 
> 09b04a528e1cb4939abb05c739b360e6 and it booted OK for me (until it failed due 
> to lack of a ramdisk). I tried recent xen-unstable and current tip of 
> xen-4.1-testing.hg (23096:45f5bdc1a90a).
>
> I've attached "bzexlode.c" if you compile it then you can use it to
> extract the payload from the vmlinuz, which you can then decompress to
> get an elf file and run /usr/lib/xen/bin/readnotes on e.g:
>          # /root/bzexplode /root/vmlinuz-2.6.35.6-45.fc14.i686.PAE | file -
>          [...]
>          /dev/stdin: gzip compressed data, from Unix, last modified: Tue Oct 19 
> 00:50:15 2010, max compression
>          # /root/bzexplode /root/vmlinuz-2.6.35.6-45.fc14.i686.PAE | zcat>  
> /tmp/x
>          [...]
>          # file /tmp/x
>          /tmp/x: ELF 32-bit LSB executable, Intel 80386, version 1 (SYSV), 
> statically linked, stripped
>          # /usr/lib/xen/bin/readnotes /tmp/x
>          GUEST_OS: linux
>          GUEST_VERSION: 2.6
>          XEN_VERSION: xen-3.0
>          VIRT_BASE: 0xc0000000 (4 bytes)
>          ENTRY: 0xc0a39000 (4 bytes)
>          HYPERCALL_PAGE: 0xc0402000 (4 bytes)
>          FEATURES: !writable_page_tables|pae_pgdir_above_4gb
>          PAE_MODE: yes
>          LOADER: generic
>          L1_MFN_VALID: mask=0x1 value=0x1
>          SUSPEND_CANCEL:        0x1 (4 bytes)
>          HV_START_LOW: 0xf5800000 (4 bytes)
>          PADDR_OFFSET:          0 (4 bytes)
>
> Does that match what you see?
>
>
> > I've seen a lot of the same errors on google but not for xen-4 and xl.
> >
> > Any helpers out there?
> >
> > TIA,
> > Mike Wright
> >
> > _______________________________________________
> > Xen-devel mailing list
> > Xen-devel@xxxxxxxxxxxxxxxxxxx
> > http://lists.xensource.com/xen-devel
>
>
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-devel

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel