|
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] Re: [Xen-devel] xen 4.2 unstable; HVM; 2.6.39.3; HD/Network card error
Hello Walter, good news - congratulations :)Do you have .deb packages for xen 4.2 unstable and the xen-kernel you have used? Thank you for your short info. regards, Mark Am 25.07.2011 00:21, schrieb Walter Robert Ditzler: hi list members, i had several problems with my new xen installations, 4.2 unstable with 2.6.39-3 and hvm guests. I can finally say that almost all problems have been gone :-) to be honest I believe the kernels 2.6.39.1/2 and 3 were the problem. this weekend I used the mainline 3.0.0 kernel with an actual version of xen 4.2 unstable, and here we go: - booting of squeeze guests, ok (before hang on grub) - booting of win 7 x64 guests, ok - booting of win 2008r2 x64 guests, ok the only little problem which has left is on squeeze guests. the squeeze guest comes up until grub. but then it takes around 2 minutes until the squeeze guest installation continues to start up. that would be really nice get to be solved in the near future. thanks walter -----Original Message----- From: Walter Robert Ditzler [mailto:ditwal001@xxxxxxxxx] Sent: Mittwoch, 20. Juli 2011 14:09 To: 'Stefano Stabellini' Cc: konrad.wilk@xxxxxxxxxx; xen-devel@xxxxxxxxxxxxxxxxxxx; xen-users@xxxxxxxxxxxxxxxxxxx Subject: RE: [Xen-devel] xen 4.2 unstable; HVM; 2.6.39.3; HD/Network card error Importance: High stefano, i found the problem, if it is really a one! I will explain it step by step what solved my problem which works for both, win7 and debian squeeze guest's: network card / network ********************** the guest network works brilliant only with that configuration: auto brX iface brX inet static address 10.41.10.42 netmask 255.255.255.0 network 10.41.10.0 broadcast 10.41.10.255 gateway 10.41.10.1 bridge_ports eth0 bridge_stp on bridge_maxwait 0 vif = [ 'bridge=brX,mac=xx:xx:xx:xx:xx:xx' ] strange is that I now have to configure a bridge interface. with older xen version it was enough to setup "bridge=eth0". now I had to setup "bridge=brX"! disk controller *************** for a windows 7 x64 guest system I got it running with: disk = [ 'phy:/dev/vgmain/lv_server01,hda,w','file:/var/xen/win7.iso,hdc:cdrom,r' ] for a debian squeeze guest system I needed to change it into: disk = [ 'phy:/dev/vgmain/lv_server01,sda,w','file:/var/xen/debian-6.0.1a-amd64-netin st.iso,hdc:cdrom,r' ] even here is strange that debian squeeze guest's now see the qemu disk as a "SDA". squeeze used to see qemu disk in older xen versions (< 4.2) as "HDA" and that definitely doesn't work anymore. I found that out having a deeper look at the debian installer log. guy's, thank you very much for your help, had become a lot of new input's. I hope I could give some useful feedback back to you too. finally I only would like to know, if this SDA-behavior is now a new behavior of xen 4.2 ++? thanks a lot, walter *** original guest config file *** name = 'server01' kernel = 'hvmloader' builder = 'hvm' device_model = 'qemu-dm' maxmem = 1024 memory = 1024 vcpus = 1 acpi = 1 apic = 1 vif = [ 'bridge=eth0,mac=00:16:3e:1a:b3:4b' ] #vfb = [ 'type=vnc,vnclisten=0.0.0.0,vncunused=0,vncdisplay=1' ] disk = [ 'phy:/dev/vgmain/lv_server01,hda,w','file:/var/xen/debian-6.0.1a-amd64-netin st.iso,hdc:cdrom,r' ] boot = 'dc' usbdevice = 'tablet' sdl = 0 stdvga = 1 serial = 'pty' on_poweroff = 'destroy' on_reboot = 'restart' on_crash = 'restart' vnc = 1 vnclisten = '0.0.0.0' vncviewer = 1 *** -----Original Message----- From: Stefano Stabellini [mailto:stefano.stabellini@xxxxxxxxxxxxx] Sent: Mittwoch, 20. Juli 2011 13:40 To: Walter Robert Ditzler Cc: Stefano Stabellini; konrad.wilk@xxxxxxxxxx; xen-devel@xxxxxxxxxxxxxxxxxxx; xen-users@xxxxxxxxxxxxxxxxxxx Subject: RE: [Xen-devel] xen 4.2 unstable; HVM; 2.6.39.3; HD/Network card error On Tue, 19 Jul 2011, Walter Robert Ditzler wrote:hi stefano, hi konrad, thanks for replying :-) i followed your suggestions and changed the guest config file. I have now the following test szenario: server01> should be a debian squeeze 6.0.1a amd64 netinst installation server02> is a successfully installed windows 7 x64 installation bellow I paste the both config files. as you can see from the screenshots:server01 installation ********************* sh11: server01_debian-installer-1.JPG sh12: server01_debian-installer-2.JPG sh13: server01_debian-installer-3.JPG the debian installation has some difficulties to find a harddisk. strange is, that the networkcard was found straight away and I became a dhcp lease from my infrastructure. server02 installation ********************* sh21: server02_xen_win7.JPG the windows has been successfully installed onto my xen guest, but!!!!! Q U E S T I O N S ***************** - why do I see my server HP DL320G5 network card and disk controller? - I thought, HVM means fully virtualized?! I expected to see something like qemu/xen harddrive and qemu/xen network card!? - Is here my xen really doing HVM - how can I do HVM, I need my guests to be transferred to any different hw boxes without need to deal with guest disk and network carddrivers? What exactly are the network card and disk controller that you are seeing in your guests? _______________________________________________ Xen-devel mailing list Xen-devel@xxxxxxxxxxxxxxxxxxx http://lists.xensource.com/xen-devel -- IT-Infrastrukturen.ORG ms@xxxxxxxxxxxxxxxxxxxxxx http://www.it-infrastrukturen.org +++ Free infrastructure software for all. +++ _______________________________________________ Xen-devel mailing list Xen-devel@xxxxxxxxxxxxxxxxxxx http://lists.xensource.com/xen-devel
|
 |
Lists.xenproject.org is hosted with RackSpace, monitoring our |