[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Xen-devel] [PATCH 3 of 3] docs/cmdline: Add some more entries



Signed-off-by: Andrew Cooper <andrew.cooper3@xxxxxxxxxx>

diff -r 2ed554fcf226 -r 9887e73fd5dc docs/misc/xen-command-line.markdown
--- a/docs/misc/xen-command-line.markdown
+++ b/docs/misc/xen-command-line.markdown
@@ -118,6 +118,12 @@ domain 0 command line
 
 ### acpi\_sleep
 ### allowsuperpage
+> `= <boolean>`
+
+> Default: `true`
+
+Permit Xen to use superpages when performing memory management.
+
 ### apic
 > `= summit | bigsmp | default`
 
@@ -128,6 +134,8 @@ there are more than 8 CPUs, Xen will swi
 ### allow\_unsafe
 > `= <boolean>`
 
+> Default: `false`
+
 Force boot on potentially unsafe systems. By default Xen will refuse to boot on
 systems with the following errata:
 
@@ -141,7 +149,20 @@ systems with the following errata:
 Increase the verbosity of the APIC code from the default value.
 
 ### ats
+> `= <boolean>`
+
+> Default: `true`
+
+Permits Xen to set up and use PCI Address Translation Services, which is 
required
+for PCI Passthrough.
+
 ### availmem
+> `= <size>`
+
+> Default: `0` (no limit)
+
+Specify a maximum amount of available memory, to which Xen will clamp the e820 
table.
+
 ### badpage
 > `= List of [ <integer> | <integer>-<integer> ]`
 
@@ -151,8 +172,23 @@ that byte `0x12345678` is bad, you would
 Xen's command line.
 
 ### bootscrub
+> `= <boolean>`
+
+> Default: `true`
+
+Scrub free RAM during boot.  This is a safety feature to prevent accidentally 
leaking
+sensitive VM data into other VMs if Xen crashes and reboots.
+
 ### cachesize
+> `= <size>`
+
+If set, override Xen's calculation of the level 2 cache line size.
+
 ### clocksource
+> `= pit | hpet | cyclone | acpi`
+
+If set, override Xen's default choice for the platform timer.
+
 ### com1,com2
 > `= <baud>[/<clock_hz>][,DPS[,<io-base>[,<irq>[,<port-bdf>[,<bridge-bdf>]]]] 
 > | pci | amt ] `
 
@@ -249,13 +285,38 @@ including omission, causes Xen to automa
 console during dom0 boot.
 
 ### cpu\_type
+> `= arch_perfmon`
+
+If set, force use of the performance counters for oprofile, rather than 
detecting
+available support.
+
 ### cpufreq
-### cpuid\_mask\_cpu
-### cpuid\_mask\_ecx
-### cpuid\_mask\_edx
-### cpuid\_mask\_ext\_ecx
-### cpuid\_mask\_ext\_edx
-### cpuid\_mask\_xsave\_eax
+> `= dom0-kernel | none | xen`
+
+> Default: `xen`
+
+Indicate where the responsibility for driving power states lies.
+
+### cpuid\_mask\_cpu (AMD only)
+> `= fam_0f_rev_c | fam_0f_rev_d | fam_0f_rev_e | fam_0f_rev_f | fam_0f_rev_g 
| fam_10_rev_b | fam_10_rev_c | fam_11_rev_b`
+
+If the other **cpuid\_mask\_{,ext\_}e{c,d}x** options are fully set 
(unspecified
+on the command line), specify a pre-canned cpuid mask to mask the current
+processor down to appear as the specified processor.  It is important to ensure
+that all hosts in a pool appear the same to guests to allow successful live
+migration.
+
+### cpuid\_mask\_ ecx,edx,ext\_ecx,ext\_edx,xsave_eax
+> `= <integer>`
+
+> Default: `~0` (all bits set)
+
+These five command line parameters are used to specify cpuid masks to help with
+cpuid levelling across a pool of hosts.  Setting a bit in the mask indicates 
that
+the feature should be enabled, while clearing a bit in the mask indicates that
+the feature should be disabled.  It is important to ensure that all hosts in a
+pool appear the same to guests to allow successful live migration.
+
 ### cpuidle
 ### cpuinfo
 ### crashinfo_maxaddr
@@ -485,7 +546,9 @@ Choose the default scheduler.
 ### serial\_tx\_buffer
 > `= <size>`
 
-Set the serial transmit buffer size.  Defaults to 16kB.
+> Default: `16kB`
+
+Set the serial transmit buffer size.
 
 ### smep
 ### snb\_igd\_quirk
@@ -543,7 +606,13 @@ The optional `keep` parameter causes Xen
 console even after dom0 has been started.  The default behaviour is to
 relinquish control to dom0.
 
-### vpid
+### vpid (Intel)
+> `= <boolean>`
+
+> Default: `true`
+
+Use Virtual Processor ID support if available.  This prevents the need for TLB
+flushes on VM entry and exit, increasing performance.
 
 ### vpmu
 > `= ( bts )`
@@ -583,5 +652,22 @@ Set the NMI watchdog timeout in seconds.
 the watchdog.
 
 ### x2apic
+> `= <boolean>`
+
+> Default: `true`
+
+Permit use of x2apic setup for SMP environments.
+
 ### x2apic\_phys
+> `= <boolean>`
+
+> Default: `true`
+
+Use the x2apic physical apic driver.  The alternative is the x2apic cluster 
driver.
+
 ### xsave
+> `= <boolean>`
+
+> Default: `true`
+
+Permit use of the `xsave/xrstor` instructions.

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
http://lists.xen.org/xen-devel


 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.