[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-devel] Claim mode and HVM PoD interact badly



On Fri, 2014-01-10 at 10:28 -0500, Konrad Rzeszutek Wilk wrote:
> On Fri, Jan 10, 2014 at 03:16:25PM +0000, Ian Campbell wrote:
> > On Fri, 2014-01-10 at 09:58 -0500, Konrad Rzeszutek Wilk wrote:
> > > Which implies to me that we _need_ the 'maxmem' amount of memory at boot 
> > > time.
> > > And then it is the responsibility of the balloon driver to give the memory
> > > back (and this is where the 'static-max' et al come in play to tell the
> > > balloon driver to balloon out).
> > 
> > PoD exists purely so that we don't need the 'maxmem' amount of memory at
> > boot time. It is basically there in order to let the guest get booted
> > far enough to load the balloon driver to give the memory back.
> > 
> > It's basically a boot time zero-page sharing mechanism AIUI.
> 
> But it does look to gulp up hypervisor memory and return it during
> allocation of memory for the guest.

It should be less than the maxmem-memory amount though. Perhaps because
Wei is using relatively small sizes the pod cache ends up being a
similar size to the saving?

Or maybe I just don't understand PoD, since the code you quote does seem
to contradict that.

Or maybe libxl's calculation of pod_target is wrong?

> From reading the code the patch seems correct - we will _need_ that
> extra 128MB 'claim' to allocate/free the 128MB extra pages. They
> are temporary as we do free them.

It does makes sense that the PoD cache should be included in the claim,
I just don't get why the cache is so big...

> > > diff --git a/tools/libxc/xc_hvm_build_x86.c 
> > > b/tools/libxc/xc_hvm_build_x86.c
> > > index 77bd365..65e9577 100644
> > > --- a/tools/libxc/xc_hvm_build_x86.c
> > > +++ b/tools/libxc/xc_hvm_build_x86.c
> > > @@ -335,7 +335,12 @@ static int setup_guest(xc_interface *xch,
> > >  
> > >      /* try to claim pages for early warning of insufficient memory 
> > > available */
> > >      if ( claim_enabled ) {
> > > -        rc = xc_domain_claim_pages(xch, dom, nr_pages - cur_pages);
> > > +        unsigned long nr = nr_pages - cur_pages;
> > > +
> > > +        if ( pod_mode )
> > > +            nr = target_pages - 0x20;
> > 
> > 0x20?
> 
> Yup. From earlier:
> 
> 305     if ( pod_mode )
> 306     {
> 307         /*
> 308          * Subtract 0x20 from target_pages for the VGA "hole".  Xen will
> 309          * adjust the PoD cache size so that domain tot_pages will be
> 310          * target_pages - 0x20 after this call.
> 311          */
> 312         rc = xc_domain_set_pod_target(xch, dom, target_pages - 0x20,
> 313                                       NULL, NULL, NULL);
> 314         if ( rc != 0 )
> 315         {
> 316             PERROR("Could not set PoD target for HVM guest.\n");
> 317             goto error_out;
> 318         }
> 319     }
> 
> Maybe a nice little 'pod_delta' or 'pod_pages' should be used instead of 
> copying
> this around.

A #define or something might be nice, yes.

> 
> > 
> > > +
> > > +        rc = xc_domain_claim_pages(xch, dom, nr);
> > >          if ( rc != 0 )
> > >          {
> > >              PERROR("Could not allocate memory for HVM guest as we cannot 
> > > claim memory!");
> > 
> > 



_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
http://lists.xen.org/xen-devel


 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.