[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Xen-devel] [XEN/ARM: Patch v4 1/1] Add support for the Exynos secure firmware



The existence of secure firmware is dictated by the presence of
"samsung,secure-firmware" in the DT.

The Arndale board does not have that entry, and uses the address as defined
in "samsung,exynos4210-sysram", offset 0 as the smp init address. This is
possibly true for all SoCs without secure firmware.

For other boards which do have a "secure-firmware" node, use sysram-ns
at offset +0x1c as the smp init address.

The "secure-firmware" MMIO range contains ways to idle the CPU. As this gets
mapped to DOM0 because of its presence in the DT, we blacklist it.

Have tested this on the Odroid XU. I have also tested the other code path
on the Odroid XU by removing "secure-firmware" from its DT. I could see
that the other code path was exercised with correct smp init address
values.

Signed-off-by: Suriyan Ramasami <suriyan.r@xxxxxxxxx>
---
This patch is based off of the staging area.

Changes between versions as follows:
v4:
* reset code hit data abort. Drop __initconst for exynos_dt_pmu_matches[]
as it is being reused after boot.
* Drop EXYNOS_CONFIG_NR_CPUS as its not being used. Nonethless we shouldn't
be hardcoding such values in Xen.

v3:
* Inline function exynos_smp_init_getbasesizeoffset as its used in only one
place.
* Call exynos_smc for SMC_CMD_CPU1BOOT only if secure_firmware is present.
* Remove EXYNOS5_PA_PMU as its value is extracted from DT.

v2:
* Consolidate exynos_smp_init_getbaseandoffset().
* Use the size from the DT as mapping length conistently.
* Do not check if the poking addresses are within size. We just expect it
to be.
* Add smc call in cpu bring up code. Linux does this call irrespective of
the presence of "secure-firmware" in the DT.
* Blacklist "samsung,secure-firmware".
* Change subject line appropriately.

v1:
* Unbreak Arndale XEN boot.
* Remove BUG_ON for checking the address offsets that we poke with.
Instead use the size field from the DT to make valid comaprisons.
---
 xen/arch/arm/platforms/exynos5.c        | 91 +++++++++++++++++++++++----------
 xen/include/asm-arm/platforms/exynos5.h |  2 -
 2 files changed, 63 insertions(+), 30 deletions(-)

diff --git a/xen/arch/arm/platforms/exynos5.c b/xen/arch/arm/platforms/exynos5.c
index 22a38f0..ac556cb 100644
--- a/xen/arch/arm/platforms/exynos5.c
+++ b/xen/arch/arm/platforms/exynos5.c
@@ -28,11 +28,28 @@
 #include <asm/platform.h>
 #include <asm/io.h>
 
+static bool_t secure_firmware;
+
 #define EXYNOS_ARM_CORE0_CONFIG     0x2000
-#define EXYNOS_ARM_CORE_CONFIG(_nr) (0x80 * (_nr))
+#define EXYNOS_ARM_CORE_CONFIG(_nr) (EXYNOS_ARM_CORE0_CONFIG + (0x80 * (_nr)))
 #define EXYNOS_ARM_CORE_STATUS(_nr) (EXYNOS_ARM_CORE_CONFIG(_nr) + 0x4)
 #define S5P_CORE_LOCAL_PWR_EN       0x3
 
+#define SMC_CMD_CPU1BOOT            (-4)
+
+static noinline void exynos_smc(register_t function_id, register_t arg0,
+                                register_t arg1, register_t arg2)
+{
+    asm volatile(
+        __asmeq("%0", "r0")
+        __asmeq("%1", "r1")
+        __asmeq("%2", "r2")
+        __asmeq("%3", "r3")
+        "smc #0"
+        :
+        : "r" (function_id), "r" (arg0), "r" (arg1), "r" (arg2));
+}
+
 static int exynos5_init_time(void)
 {
     uint32_t reg;
@@ -42,8 +59,6 @@ static int exynos5_init_time(void)
     u64 mct_base_addr;
     u64 size;
 
-    BUILD_BUG_ON(EXYNOS5_MCT_G_TCON >= PAGE_SIZE);
-
     node = dt_find_compatible_node(NULL, NULL, "samsung,exynos4210-mct");
     if ( !node )
     {
@@ -61,7 +76,7 @@ static int exynos5_init_time(void)
     dprintk(XENLOG_INFO, "mct_base_addr: %016llx size: %016llx\n",
             mct_base_addr, size);
 
-    mct = ioremap_attr(mct_base_addr, PAGE_SIZE, PAGE_HYPERVISOR_NOCACHE);
+    mct = ioremap_attr(mct_base_addr, size, PAGE_HYPERVISOR_NOCACHE);
     if ( !mct )
     {
         dprintk(XENLOG_ERR, "Unable to map MCT\n");
@@ -93,30 +108,47 @@ static int exynos5250_specific_mapping(struct domain *d)
 
 static int __init exynos5_smp_init(void)
 {
-    void __iomem *sysram;
     struct dt_device_node *node;
-    u64 sysram_ns_base_addr;
+    void __iomem *sysram;
+    char *compatible;
+    u64 sysram_addr;
     u64 size;
+    u64 sysram_offset;
     int rc;
 
-    node = dt_find_compatible_node(NULL, NULL, "samsung,exynos4210-sysram");
+    node = dt_find_compatible_node(NULL, NULL, "samsung,secure-firmware");
+    if ( node )
+    {
+        /* Have to use sysram_ns_base_addr + 0x1c for boot address */
+        compatible = "samsung,exynos4210-sysram-ns";
+        sysram_offset = 0x1c;
+        secure_firmware = 1;
+        printk("Running under secure firmware.\n");
+    }
+    else
+    {
+        /* Have to use sysram_base_addr + offset 0 for boot address */
+        compatible = "samsung,exynos4210-sysram";
+        sysram_offset = 0;
+    }
+
+    node = dt_find_compatible_node(NULL, NULL, compatible);
     if ( !node )
     {
-        dprintk(XENLOG_ERR, "samsung,exynos4210-sysram-ns missing in DT\n");
+        dprintk(XENLOG_ERR, "%s missing in DT\n", compatible);
         return -ENXIO;
     }
 
-    rc = dt_device_get_address(node, 0, &sysram_ns_base_addr, &size);
+    rc = dt_device_get_address(node, 0, &sysram_addr, &size);
     if ( rc )
     {
-        dprintk(XENLOG_ERR, "Error in \"samsung,exynos4210-sysram-ns\"\n");
+        dprintk(XENLOG_ERR, "Error in %s\n", compatible);
         return -ENXIO;
     }
+    dprintk(XENLOG_INFO, "sysram_addr: %016llx size: %016llx offset: 
%016llx\n",
+            sysram_addr, size, sysram_offset);
 
-    dprintk(XENLOG_INFO, "sysram_ns_base_addr: %016llx size: %016llx\n",
-            sysram_ns_base_addr, size);
-
-    sysram = ioremap_nocache(sysram_ns_base_addr, PAGE_SIZE);
+    sysram = ioremap_nocache(sysram_addr, size);
     if ( !sysram )
     {
         dprintk(XENLOG_ERR, "Unable to map exynos5 MMIO\n");
@@ -125,7 +157,7 @@ static int __init exynos5_smp_init(void)
 
     printk("Set SYSRAM to %"PRIpaddr" (%p)\n",
            __pa(init_secondary), init_secondary);
-    writel(__pa(init_secondary), sysram);
+    writel(__pa(init_secondary), sysram + sysram_offset);
 
     iounmap(sysram);
 
@@ -135,7 +167,7 @@ static int __init exynos5_smp_init(void)
 static int exynos_cpu_power_state(void __iomem *power, int cpu)
 {
     return __raw_readl(power + EXYNOS_ARM_CORE_STATUS(cpu)) &
-                       S5P_CORE_LOCAL_PWR_EN;
+           S5P_CORE_LOCAL_PWR_EN;
 }
 
 static void exynos_cpu_power_up(void __iomem *power, int cpu)
@@ -171,11 +203,11 @@ static int exynos5_cpu_power_up(void __iomem *power, int 
cpu)
     return 0;
 }
 
-static int exynos5_get_pmu_base_addr(u64 *power_base_addr) {
-    u64 size;
+static int exynos5_get_pmu_baseandsize(u64 *power_base_addr, u64 *size)
+{
     struct dt_device_node *node;
     int rc;
-    static const struct dt_device_match exynos_dt_pmu_matches[] __initconst =
+    static const struct dt_device_match exynos_dt_pmu_matches[] =
     {
         DT_MATCH_COMPATIBLE("samsung,exynos5250-pmu"),
         DT_MATCH_COMPATIBLE("samsung,exynos5410-pmu"),
@@ -190,7 +222,7 @@ static int exynos5_get_pmu_base_addr(u64 *power_base_addr) {
         return -ENXIO;
     }
 
-    rc = dt_device_get_address(node, 0, power_base_addr, &size);
+    rc = dt_device_get_address(node, 0, power_base_addr, size);
     if ( rc )
     {
         dprintk(XENLOG_ERR, "Error in \"samsung,exynos5XXX-pmu\"\n");
@@ -198,7 +230,7 @@ static int exynos5_get_pmu_base_addr(u64 *power_base_addr) {
     }
 
     dprintk(XENLOG_DEBUG, "power_base_addr: %016llx size: %016llx\n",
-            *power_base_addr, size);
+            *power_base_addr, *size);
 
     return 0;
 }
@@ -206,15 +238,15 @@ static int exynos5_get_pmu_base_addr(u64 
*power_base_addr) {
 static int exynos5_cpu_up(int cpu)
 {
     u64 power_base_addr;
+    u64 size;
     void __iomem *power;
     int rc;
 
-    rc = exynos5_get_pmu_base_addr(&power_base_addr);
+    rc = exynos5_get_pmu_baseandsize(&power_base_addr, &size);
     if ( rc )
         return rc;
 
-    power = ioremap_nocache(power_base_addr +
-                            EXYNOS_ARM_CORE0_CONFIG, PAGE_SIZE);
+    power = ioremap_nocache(power_base_addr, size);
     if ( !power )
     {
         dprintk(XENLOG_ERR, "Unable to map power MMIO\n");
@@ -230,22 +262,24 @@ static int exynos5_cpu_up(int cpu)
 
     iounmap(power);
 
+    if ( secure_firmware )
+        exynos_smc(SMC_CMD_CPU1BOOT, cpu, 0, 0);
+
     return cpu_up_send_sgi(cpu);
 }
 
 static void exynos5_reset(void)
 {
     u64 power_base_addr;
+    u64 size;
     void __iomem *pmu;
     int rc;
 
-    BUILD_BUG_ON(EXYNOS5_SWRESET >= PAGE_SIZE);
-
-    rc = exynos5_get_pmu_base_addr(&power_base_addr);
+    rc = exynos5_get_pmu_baseandsize(&power_base_addr, &size);
     if ( rc )
         return;
 
-    pmu = ioremap_nocache(power_base_addr, PAGE_SIZE);
+    pmu = ioremap_nocache(power_base_addr, size);
     if ( !pmu )
     {
         dprintk(XENLOG_ERR, "Unable to map PMU\n");
@@ -264,6 +298,7 @@ static const struct dt_device_match exynos5_blacklist_dev[] 
__initconst =
      * This is result to random freeze.
      */
     DT_MATCH_COMPATIBLE("samsung,exynos4210-mct"),
+    DT_MATCH_COMPATIBLE("samsung,secure-firmware"),
     { /* sentinel */ },
 };
 
diff --git a/xen/include/asm-arm/platforms/exynos5.h 
b/xen/include/asm-arm/platforms/exynos5.h
index c88455a..aef5c67 100644
--- a/xen/include/asm-arm/platforms/exynos5.h
+++ b/xen/include/asm-arm/platforms/exynos5.h
@@ -6,8 +6,6 @@
 
 #define EXYNOS5_PA_CHIPID           0x10000000
 #define EXYNOS5_PA_TIMER            0x12dd0000
-/* Base address of system controller */
-#define EXYNOS5_PA_PMU              0x10040000
 
 #define EXYNOS5_SWRESET             0x0400      /* Relative to PA_PMU */
 
-- 
1.9.1


_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
http://lists.xen.org/xen-devel


 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.