[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] Re: [Xen-devel] [PATCH V2 4/8] xen/arm: Use the new mapping relations between vCPUID and vMPIDR
Hi Chen, On 23/05/2015 14:52, Chen Baozi wrote: From: Chen Baozi <baozich@xxxxxxxxx> There are 3 places to change: * Initialise vMPIDR value in vcpu_initialise() * Find the vCPU from vMPIDR affinity information when accessing GICD registers in vGIC * Find the vCPU from vMPIRR affinity information when booting with vPSCI s/VMPIRR/vMPIDR/ in vGIC Signed-off-by: Chen Baozi <baozich@xxxxxxxxx> --- xen/arch/arm/domain.c | 6 +----- xen/arch/arm/vgic-v3.c | 22 +++++++--------------- xen/arch/arm/vpsci.c | 2 +- 3 files changed, 9 insertions(+), 21 deletions(-) diff --git a/xen/arch/arm/domain.c b/xen/arch/arm/domain.c index 2bde26e..0cf147c 100644 --- a/xen/arch/arm/domain.c +++ b/xen/arch/arm/domain.c @@ -501,11 +501,7 @@ int vcpu_initialise(struct vcpu *v) v->arch.sctlr = SCTLR_GUEST_INIT; - /* - * By default exposes an SMP system with AFF0 set to the VCPU ID - * TODO: Handle multi-threading processor and cluster - */ - v->arch.vmpidr = MPIDR_SMP | (v->vcpu_id << MPIDR_AFF0_SHIFT); + v->arch.vmpidr = MPIDR_SMP | vcpuid_to_vaffinity(v->vcpu_id); v->arch.actlr = READ_SYSREG32(ACTLR_EL1); diff --git a/xen/arch/arm/vgic-v3.c b/xen/arch/arm/vgic-v3.c index 40e1892..12007d8 100644 --- a/xen/arch/arm/vgic-v3.c +++ b/xen/arch/arm/vgic-v3.c @@ -50,14 +50,6 @@ */ #define VGICD_CTLR_DEFAULT (GICD_CTLR_ARE_NS) -static struct vcpu *vgic_v3_irouter_to_vcpu(struct vcpu *v, uint64_t irouter) -{ - irouter &= ~(GICD_IROUTER_SPI_MODE_ANY); - irouter = irouter & MPIDR_AFF0_MASK; - - return v->domain->vcpu[irouter]; -} - static uint64_t vgic_v3_vcpu_to_irouter(struct vcpu *v, unsigned int vcpu_id) { @@ -80,9 +72,7 @@ static struct vcpu *vgic_v3_get_target_vcpu(struct vcpu *v, unsigned int irq) ASSERT(spin_is_locked(&rank->lock)); - target = rank->v3.irouter[irq % 32]; - target &= ~(GICD_IROUTER_SPI_MODE_ANY); - target &= MPIDR_AFF0_MASK; + target = vaffinity_to_vcpuid(rank->v3.irouter[irq % 32]); When irouter.IRM = 1 (i.e any processor can be used for SPIs), the affinity may be unknown. Although, when this register is saved we make sure to have AFF0 and AFF1 set to 0. This change, as the current wasn't clear about it. I would be tempt to add a specific case for irouter.IRM = 1. But I don't mind if you only add a comment. ASSERT(target >= 0 && target < v->domain->max_vcpus); return v->domain->vcpu[target]; @@ -751,7 +741,7 @@ static int vgic_v3_distr_mmio_read(struct vcpu *v, mmio_info_t *info) vgic_unlock_rank(v, rank, flags); return 1; } - vcpu_id = irouter; + vcpu_id = vaffinity_to_vcpuid(irouter); *r = vgic_v3_vcpu_to_irouter(v, vcpu_id); The current code is very pointless, irouter contains the value to return. vgic_v3_vcpu_to_irouter is just an identity function. The read emulation for IROUTER can be simplify a lot to only returns the value irouter which is already valid. I can send a patch to apply before your series to clean up this IROUTER code. I would make unnecessary some of your changes. vgic_unlock_rank(v, rank, flags); return 1; @@ -841,6 +831,7 @@ static int vgic_v3_distr_mmio_write(struct vcpu *v, mmio_info_t *info) uint64_t new_irouter, new_target, old_target; struct vcpu *old_vcpu, *new_vcpu; int gicd_reg = (int)(info->gpa - v->domain->arch.vgic.dbase); + uint32_t vcpu_id; perfc_incr(vgicd_writes); @@ -925,8 +916,9 @@ static int vgic_v3_distr_mmio_write(struct vcpu *v, mmio_info_t *info) } else { - new_target = new_irouter & MPIDR_AFF0_MASK; - if ( new_target >= v->domain->max_vcpus ) + new_target = new_irouter & MPIDR_HWID_MASK; + vcpu_id = vaffinity_to_vcpuid(new_irouter); + if ( vcpu_id >= v->domain->max_vcpus ) { printk(XENLOG_G_DEBUG "%pv: vGICD: wrong irouter at offset %#08x\n val 0x%lx vcpu %x", @@ -934,7 +926,7 @@ static int vgic_v3_distr_mmio_write(struct vcpu *v, mmio_info_t *info) vgic_unlock_rank(v, rank, flags); return 0; } - new_vcpu = vgic_v3_irouter_to_vcpu(v, new_irouter); I would prefer to keep vgic_v3_irouter_to_vcpu and return NULL if the VCPU ID is too high. The emulation code would be: new_vcpu = vgic_v3_irouter_to_vcpu(v, new_irouter); if ( !new_vcpu ) { printk(.....); }Although the current emulation is wrong, if the guest is passing a wrong MPIDR, we should just ignore the setting and let the interrupt going pending. Anyway, I think it would require more work in Xen so I'm okay with the current behavior. + new_vcpu = v->domain->vcpu[vcpu_id]; } rank->v3.irouter[REG_RANK_INDEX(64, (gicd_reg - GICD_IROUTER), diff --git a/xen/arch/arm/vpsci.c b/xen/arch/arm/vpsci.c index 5d899be..1c1e7de 100644 --- a/xen/arch/arm/vpsci.c +++ b/xen/arch/arm/vpsci.c @@ -33,7 +33,7 @@ static int do_common_cpu_on(register_t target_cpu, register_t entry_point, register_t vcpuid; if( ver == XEN_PSCI_V_0_2 ) - vcpuid = (target_cpu & MPIDR_HWID_MASK); + vcpuid = vaffinity_to_vcpuid(target_cpu); else vcpuid = target_cpu; AFAICT in PSCI 0.1, target_cpu is a CPUID which is a MPIDR-like value. If so, I think we may need to call vaffinity_to_vcpuid. But, I wasn't able to confirm with the spec. I guessed it from the Linux usage. Maybe there is limit of number of CPU used with PSCI 0.1? Regards, -- Julien Grall _______________________________________________ Xen-devel mailing list Xen-devel@xxxxxxxxxxxxx http://lists.xen.org/xen-devel
|
Lists.xenproject.org is hosted with RackSpace, monitoring our |