[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] Re: [Xen-devel] Unable to boot Xen 4.7-rc4 on HiKey
On Thu, Jun 2, 2016 at 11:02 AM, Julien Grall <julien.grall@xxxxxxx> wrote: > > > On 02/06/16 17:53, Tamas K Lengyel wrote: >> >> On Thu, Jun 2, 2016 at 4:34 PM, Chenxiao Zhao <chenxiao.zhao@xxxxxxxxx> >> wrote: >>> >>> >>> >>> On 6/1/2016 6:09 PM, Tamas K Lengyel wrote: >>>> >>>> >>>> On Wed, Jun 1, 2016 at 3:49 PM, Julien Grall <julien.grall@xxxxxxx> >>>> wrote: >>>>> >>>>> >>>>> On 01/06/2016 18:10, Tamas K Lengyel wrote: >>>>>> >>>>>> >>>>>> >>>>>> Hi all, >>>>> >>>>> >>>>> >>>>> >>>>> Hi Tamas, >>>>> >>>>>> following the steps from http://wiki.xen.org/wiki/HiKey I'm unable to >>>>>> get the board to boot Xen. I'm using the Debian reference image from >>>>>> linaro as base >>>>>> (https://builds.96boards.org/releases/hikey/linaro/debian/latest/) >>>>>> and that boots fine both from the SD card directly and through >>>>>> startup.nsh. However, when I try to boot Xen I see only the following: >>>>>> >>>>>> Xen 4.7.0-rc (c/s Mon May 23 12:07:20 2016 +0100 git:8478c94-dirty) >>>>>> EFI >>>>>> loader >>>>>> Using configuration file 'xen.cfg' >>>>>> Image: 0x000000007a121000-0x000000007acb8a70 >>>>>> >>>>>> After that no output and dom0 never comes online on the network >>>>>> either. I tried compiling Xen on the device itself in case it was a >>>>>> problem with my cross-compile setup but no difference. Also with and >>>>>> without debug=y. Any tips on what might be going wrong here? >>>>> >>>>> >>>>> >>>>> >>>>> I gave a quick look at the upstream device-tree of the hikey, the path >>>>> /smb/uart@f7113000. >>>>> >>>>> If you use the upstream device-tree, it should be able to find the >>>>> correct >>>>> UART via "stdout-path" and therefore dtuart=... should not be >>>>> necessary. >>>>> >>>>> Let me know if it works for you, and I will update the wiki page. >>>> >>>> >>>> >>>> No, I removed the dtuart=... part from xen.cfg but there is no >>>> difference in the output and dom0 never comes up on the network >>>> either. >>> >>> >>> >>> Hi Tamas, >>> >>> My xen.cfg for Hikey is like this: >>> >>> options=dom0_mem=1024M dom0_max_vcpus=8 conswitch=x console=dtuart >>> dtuart=/smb/uart@f7113000 >>> kernel=Image console=hvc root=/dev/mmcblk0p9 rootwait rw 3 >>> dtb=hi6220-hikey.dtb >>> >>> hope this could help you. >> >> >> Ah, thank you! Yes, the fact that the dtb goes in a third line in the >> cfg was missing! Should be put on wiki! I finally see Xen booting but >> dom0 still doesn't start. > > > Well, the firmware should provide a valid device-tree, and therefore > "dtb=..." should not be necessary. > > The way forward is too check why the UEFI firmware does not provide a Device > Tree (or maybe the DT path to the UART is different). > The UEFI firmware is the stock one that came with it. Tamas _______________________________________________ Xen-devel mailing list Xen-devel@xxxxxxxxxxxxx http://lists.xen.org/xen-devel
|
Lists.xenproject.org is hosted with RackSpace, monitoring our |