[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Xen-devel] [PATCH V5 3/4] xen/arm: Extend SCIF early prink code to handle other interfaces



From: Oleksandr Tyshchenko <oleksandr_tyshchenko@xxxxxxxx>

Extend early prink code to be able to handle other SCIF(X)
compatible interfaces as well. These interfaces have lot in common,
but mostly differ in offsets and bits for some registers.

Introduce "EARLY_PRINTK_VERSION" config option to choose which
interface version should be used (to properly apply register offsets).

Please note, nothing has been technically changed for Renesas "Lager"
and other supported boards (SCIF).

The "EARLY_PRINTK_VERSION" option for that board should be empty:
CONFIG_EARLY_PRINTK=scif,0xe6e60000

Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@xxxxxxxx>
CC: Julien Grall <julien.grall@xxxxxxx>

---
    Changes in v3:
        - It was decided not to introduce new debug-scifa.inc
          for handling SCIFA interface, but to extend existing
          debug-scif.inc for handling both interfaces.
          This patch is a result of splitting an initial patch
          "xen/arm: Add SCIFA UART support for early printk"
          and only reworks a code

    Changes in v4:
        - Update docs/misc/arm/early-printk.txt with the new option

    Changes in v5:
        - Cosmetic fixes (text and comments in code)
---
 docs/misc/arm/early-printk.txt    |  5 +++++
 xen/arch/arm/Rules.mk             |  7 +++++++
 xen/arch/arm/arm32/debug-scif.inc | 17 +++++++++++------
 3 files changed, 23 insertions(+), 6 deletions(-)

diff --git a/docs/misc/arm/early-printk.txt b/docs/misc/arm/early-printk.txt
index b23c54f..89e081e 100644
--- a/docs/misc/arm/early-printk.txt
+++ b/docs/misc/arm/early-printk.txt
@@ -27,6 +27,11 @@ CONFIG_EARLY_PRINTK=<INC>,<BASE_ADDRESS>,<OTHER_OPTIONS>
       If <BAUD_RATE> is not given then the code will not try to
       initialize the UART, so that bootloader or firmware settings can
      be used for maximum compatibility.
+  - scif,<BASE_ADDRESS>,<VERSION>
+    - SCIF<VERSION> is, optionally, the interface version of the UART.
+
+      If <VERSION> is not given then the default interface version (SCIF)
+      will be used.
   - For all other uarts there are no additional options.
 
 As a convenience it is also possible to select from a list of
diff --git a/xen/arch/arm/Rules.mk b/xen/arch/arm/Rules.mk
index f264592..3d9a0ed 100644
--- a/xen/arch/arm/Rules.mk
+++ b/xen/arch/arm/Rules.mk
@@ -68,6 +68,13 @@ EARLY_PRINTK_INIT_UART := y
 EARLY_PRINTK_BAUD := $(word 3,$(EARLY_PRINTK_CFG))
 endif
 endif
+ifeq ($(EARLY_PRINTK_INC),scif)
+ifneq ($(word 3,$(EARLY_PRINTK_CFG)),)
+CFLAGS-y += -DEARLY_PRINTK_VERSION_$(word 3,$(EARLY_PRINTK_CFG))
+else
+CFLAGS-y += -DEARLY_PRINTK_VERSION_NONE
+endif
+endif
 
 ifneq ($(EARLY_PRINTK_INC),)
 EARLY_PRINTK := y
diff --git a/xen/arch/arm/arm32/debug-scif.inc 
b/xen/arch/arm/arm32/debug-scif.inc
index 143f05d..6f60e01 100644
--- a/xen/arch/arm/arm32/debug-scif.inc
+++ b/xen/arch/arm/arm32/debug-scif.inc
@@ -19,28 +19,33 @@
 
 #include <asm/scif-uart.h>
 
+#ifdef EARLY_PRINTK_VERSION_NONE
+#define STATUS_REG    SCIF_SCFSR
+#define TX_FIFO_REG   SCIF_SCFTDR
+#endif
+
 /*
- * SCIF UART wait UART to be ready to transmit
+ * Wait UART to be ready to transmit
  * rb: register which contains the UART base address
  * rc: scratch register
  */
 .macro early_uart_ready rb rc
 1:
-        ldrh   \rc, [\rb, #SCIF_SCFSR]   /* <- SCFSR (status register) */
+        ldrh   \rc, [\rb, #STATUS_REG]   /* Read status register */
         tst    \rc, #SCFSR_TDFE          /* Check TDFE bit */
         beq    1b                        /* Wait for the UART to be ready */
 .endm
 
 /*
- * SCIF UART transmit character
+ * UART transmit character
  * rb: register which contains the UART base address
  * rt: register which contains the character to transmit
  */
 .macro early_uart_transmit rb rt
-        strb   \rt, [\rb, #SCIF_SCFTDR]                  /* -> SCFTDR (data 
register) */
-        ldrh   \rt, [\rb, #SCIF_SCFSR]                   /* <- SCFSR (status 
register) */
+        strb   \rt, [\rb, #TX_FIFO_REG]                  /* Write data 
register */
+        ldrh   \rt, [\rb, #STATUS_REG]                   /* Read status 
register */
         and    \rt, \rt, #(~(SCFSR_TEND | SCFSR_TDFE))   /* Clear TEND and 
TDFE bits */
-        strh   \rt, [\rb, #SCIF_SCFSR]                   /* -> SCFSR (status 
register) */
+        strh   \rt, [\rb, #STATUS_REG]                   /* Write status 
register */
 .endm
 
 /*
-- 
2.7.4


_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxxx
https://lists.xenproject.org/mailman/listinfo/xen-devel

 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.