[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Xen 4.14.1 on RPI4: device tree generation failed



On Mon, Feb 1, 2021 at 12:54 AM Elliott Mitchell <ehem+xen@xxxxxxx> wrote:
>
> On Sun, Jan 31, 2021 at 10:06:21PM -0500, Tamas K Lengyel wrote:
> > With rpi-4.19.y kernel and dtbs
> > (cc39f1c9f82f6fe5a437836811d906c709e0661c) Xen boots fine and the
> > previous error is not present. I get the boot log on the serial with
> > just console=hvc0 from dom0 but the kernel ends up in a panic down the
> > line:
>
> > This seems to have been caused by a monitor being attached to the HDMI
> > port, with HDMI unplugged dom0 boots OK.
>
> The balance of reports seem to suggest 5.10 is the way to go if you want
> graphics on a RP4 with Xen.  Even without Xen 4.19 is looking rickety on
> RP4.
>
>
> On Sun, Jan 31, 2021 at 09:43:13PM -0500, Tamas K Lengyel wrote:
> > On Sun, Jan 31, 2021 at 8:59 PM Elliott Mitchell <ehem+xen@xxxxxxx> wrote:
> > >
> > > On Sun, Jan 31, 2021 at 06:50:36PM -0500, Tamas K Lengyel wrote:
> > > > On Sun, Jan 31, 2021 at 6:33 PM Elliott Mitchell <ehem+undef@xxxxxxx> 
> > > > wrote:
> > > > > Presently the rpixen script is grabbing the RPF's 4.19 branch, dates
> > > > > point to that last being touched last year.  Their tree is at
> > > > > cc39f1c9f82f6fe5a437836811d906c709e0661c.
> > > >
> > > > I've moved the Linux branch up to 5.10 because there had been a fair
> > > > amount of work that went into fixing Xen on RPI4, which got merged
> > > > into 5.9 and I would like to be able to build upstream everything
> > > > without the custom patches coming with the rpixen script repo.
> > >
> > > Please keep track of where your kernel source is checked out at since
> > > there was a desire to figure out what was going on with the device-trees.
> > >
> > >
> > > Including "console=hvc0 console=AMA0 console=ttyS0 console=tty0" in the
> > > kernel command-line should ensure you get output from the kernel if it
> > > manages to start (yes, Linux does support having multiple consoles at the
> > > same time).
> >
> > No output from dom0 received even with the added console options
> > (+earlyprintk=xen). The kernel build was from rpi-5.10.y
> > c9226080e513181ffb3909a905e9c23b8a6e8f62. I'll check if it still boots
> > with 4.19 next.
>
> So, their current HEAD.  This reads like you've got a problematic kernel
> configuration.  What procedure are you following to generate the
> configuration you use?
>
> Using their upstream as a base and then adding the configuration options
> for Xen has worked fairly well for me (`make bcm2711_defconfig`,
> `make menuconfig`, `make zImage`).
>
> Notably the options:
> CONFIG_PARAVIRT
> CONFIG_XEN_DOM0
> CONFIG_XEN
> CONFIG_XEN_BLKDEV_BACKEND
> CONFIG_XEN_NETDEV_BACKEND
> CONFIG_HVC_XEN
> CONFIG_HVC_XEN_FRONTEND
>
> Should be set to "y".

Yes, these configs are all set the same way for all Linux builds by the script:
        make O=.build-arm64 ARCH=arm64
CROSS_COMPILE=aarch64-none-linux-gnu- bcm2711_defconfig xen.config

I tried with both the rpi-5.10.y and rpi-5.9.y, neither boot up as
dom0. So far only 4.19 boots.

Tamas



 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.