[PATCH v2 2/3] x86/hpet: Don't enable legacy replacement mode unconditionally

[Andrew Cooper <andrew.cooper3@xxxxxxxxxx>]

From: Jan Beulich <jbeulich@xxxxxxxx>

Commit e1de4c196a2e ("x86/timer: Fix boot on Intel systems using ITSSPRC
static PIT clock gating") was reported to cause boot failures on certain
AMD Ryzen systems.

Refine the fix to do nothing in the default case, and only attempt to
configure legacy replacement mode if IRQ0 is found to not be working.

In addition, introduce a "hpet" command line option so this heuristic
can be overridden.  Since it makes little sense to introduce just
"hpet=legacy-replacement", also allow for a boolean argument as well as
"broadcast" to replace the separate "hpetbroadcast" option.

Signed-off-by: Jan Beulich <jbeulich@xxxxxxxx>
Signed-off-by: Andrew Cooper <andrew.cooper3@xxxxxxxxxx>
---
CC: Jan Beulich <JBeulich@xxxxxxxx>
CC: Roger Pau Monné <roger.pau@xxxxxxxxxx>
CC: Wei Liu <wl@xxxxxxx>
CC: Ian Jackson <iwj@xxxxxxxxxxxxxx>
CC: Marek Marczykowski-Górecki <marmarek@xxxxxxxxxxxxxxxxxxxxxx>
CC: Frédéric Pierret <frederic.pierret@xxxxxxxxxxxx>

v2:
 * Reinstate missing hunk from Jan's original patch.
 * Fix up "8254 PIT".
 * Drop "goto retry".

For 4.15: Attempt to unbreak AMD Ryzen 1800X systems.
---
 docs/misc/xen-command-line.pandoc | 33 +++++++++++++++++++++++++++
 xen/arch/x86/hpet.c               | 48 +++++++++++++++++++++++++--------------
 xen/arch/x86/io_apic.c            | 27 ++++++++++++++++++++++
 xen/include/asm-x86/hpet.h        |  1 +
 4 files changed, 92 insertions(+), 17 deletions(-)

diff --git a/docs/misc/xen-command-line.pandoc 
b/docs/misc/xen-command-line.pandoc
index a0601ff838..a4bd3f12c5 100644
--- a/docs/misc/xen-command-line.pandoc
+++ b/docs/misc/xen-command-line.pandoc
@@ -1274,9 +1274,42 @@ supported. See docs/misc/arm/big.LITTLE.txt for more 
information.
 When the hmp-unsafe option is disabled (default), CPUs that are not
 identical to the boot CPU will be parked and not used by Xen.
 
+### hpet
+    = List of [ <bool> | broadcast=<bool> | legacy-replacement=<bool> ]
+
+    Applicability: x86
+
+Controls Xen's use of the system's High Precision Event Timer.  By default,
+Xen will use an HPET when available and not subject to errata.  Use of the
+HPET can be disabled by specifying `hpet=0`.
+
+ * The `broadcast` boolean is disabled by default, but forces Xen to keep
+   using the broadcast for CPUs in deep C-states even when an RTC interrupt is
+   enabled.  This then also affects raising of the RTC interrupt.
+
+ * The `legacy-replacement` boolean allows for control over whether Legacy
+   Replacement mode is enabled.
+
+   Legacy Replacement mode is intended for hardware which does not have an
+   8254 PIT, and allows the HPET to be configured into a compatible mode.
+   Intel chipsets from Skylake/ApolloLake onwards can turn the PIT off for
+   power saving reasons, and there is no platform-agnostic mechanism for
+   discovering this.
+
+   By default, Xen will not change hardware configuration, unless the PIT
+   appears to be absent, at which point Xen will try to enable Legacy
+   Replacement mode before falling back to pre-IO-APIC interrupt routing
+   options.
+
+   This behaviour can be inhibited by specifying `legacy-replacement=0`.
+   Alternatively, this mode can be enabled unconditionally (if available) by
+   specifying `legacy-replacement=1`.
+
 ### hpetbroadcast (x86)
 > `= <boolean>`
 
+Deprecated alternative of `hpet=broadcast`.
+
 ### hvm_debug (x86)
 > `= <integer>`
 
diff --git a/xen/arch/x86/hpet.c b/xen/arch/x86/hpet.c
index c1d04f184f..bfa75f135a 100644
--- a/xen/arch/x86/hpet.c
+++ b/xen/arch/x86/hpet.c
@@ -52,6 +52,8 @@ static unsigned int __read_mostly num_hpets_used;
 DEFINE_PER_CPU(struct hpet_event_channel *, cpu_bc_channel);
 
 unsigned long __initdata hpet_address;
+int8_t __initdata opt_hpet_legacy_replacement = -1;
+static bool __initdata opt_hpet = true;
 u8 __initdata hpet_blockid;
 u8 __initdata hpet_flags;
 
@@ -63,6 +65,32 @@ u8 __initdata hpet_flags;
 static bool __initdata force_hpet_broadcast;
 boolean_param("hpetbroadcast", force_hpet_broadcast);
 
+static int __init parse_hpet_param(const char *s)
+{
+    const char *ss;
+    int val, rc = 0;
+
+    do {
+        ss = strchr(s, ',');
+        if ( !ss )
+            ss = strchr(s, '\0');
+
+        if ( (val = parse_bool(s, ss)) >= 0 )
+            opt_hpet = val;
+        else if ( (val = parse_boolean("broadcast", s, ss)) >= 0 )
+            force_hpet_broadcast = val;
+        else if ( (val = parse_boolean("legacy-replacement", s, ss)) >= 0 )
+            opt_hpet_legacy_replacement = val;
+        else
+            rc = -EINVAL;
+
+        s = ss + 1;
+    } while ( *ss );
+
+    return rc;
+}
+custom_param("hpet", parse_hpet_param);
+
 /*
  * Calculate a multiplication factor for scaled math, which is used to convert
  * nanoseconds based values to clock ticks:
@@ -820,12 +848,9 @@ u64 __init hpet_setup(void)
     unsigned int hpet_id, hpet_period;
     unsigned int last, rem;
 
-    if ( hpet_rate )
+    if ( hpet_rate || !hpet_address || !opt_hpet )
         return hpet_rate;
 
-    if ( hpet_address == 0 )
-        return 0;
-
     set_fixmap_nocache(FIX_HPET_BASE, hpet_address);
 
     hpet_id = hpet_read32(HPET_ID);
@@ -852,19 +877,8 @@ u64 __init hpet_setup(void)
     if ( (rem * 2) > hpet_period )
         hpet_rate++;
 
-    /*
-     * Intel chipsets from Skylake/ApolloLake onwards can statically clock
-     * gate the 8259 PIT.  This option is enabled by default in slightly later
-     * systems, as turning the PIT off is a prerequisite to entering the C11
-     * power saving state.
-     *
-     * Xen currently depends on the legacy timer interrupt being active while
-     * IRQ routing is configured.
-     *
-     * Reconfigure the HPET into legacy mode to re-establish the timer
-     * interrupt.
-     */
-    hpet_enable_legacy_replacement_mode();
+    if ( opt_hpet_legacy_replacement > 0 )
+        hpet_enable_legacy_replacement_mode();
 
     return hpet_rate;
 }
diff --git a/xen/arch/x86/io_apic.c b/xen/arch/x86/io_apic.c
index e93265f379..3f131a81fb 100644
--- a/xen/arch/x86/io_apic.c
+++ b/xen/arch/x86/io_apic.c
@@ -29,6 +29,8 @@
 #include <xen/acpi.h>
 #include <xen/keyhandler.h>
 #include <xen/softirq.h>
+
+#include <asm/hpet.h>
 #include <asm/mc146818rtc.h>
 #include <asm/smp.h>
 #include <asm/desc.h>
@@ -1930,6 +1932,31 @@ static void __init check_timer(void)
             local_irq_restore(flags);
             return;
         }
+
+        /*
+         * Intel chipsets from Skylake/ApolloLake onwards can statically clock
+         * gate the 8254 PIT.  This option is enabled by default in slightly
+         * later systems, as turning the PIT off is a prerequisite to entering
+         * the C11 power saving state.
+         *
+         * Xen currently depends on the legacy timer interrupt being active
+         * while IRQ routing is configured.
+         *
+         * If the user hasn't made an explicit choice, attempt to reconfigure
+         * the HPET into legacy mode to re-establish the timer interrupt.
+         */
+        if ( opt_hpet_legacy_replacement < 0 &&
+             hpet_enable_legacy_replacement_mode() )
+        {
+            printk(XENLOG_ERR "..no 8254 timer found - trying HPET Legacy 
Replacement Mode\n");
+
+            if ( timer_irq_works() )
+            {
+                local_irq_restore(flags);
+                return;
+            }
+        }
+
         clear_IO_APIC_pin(apic1, pin1);
         printk(KERN_ERR "..MP-BIOS bug: 8254 timer not connected to "
                "IO-APIC\n");
diff --git a/xen/include/asm-x86/hpet.h b/xen/include/asm-x86/hpet.h
index 50176de3d2..07bc8d6079 100644
--- a/xen/include/asm-x86/hpet.h
+++ b/xen/include/asm-x86/hpet.h
@@ -53,6 +53,7 @@
 extern unsigned long hpet_address;
 extern u8 hpet_blockid;
 extern u8 hpet_flags;
+extern int8_t opt_hpet_legacy_replacement;
 
 /*
  * Detect and initialise HPET hardware: return counter update frequency.
-- 
2.11.0