[XEN PATCH v7 17/51] build: set XEN_BUILD_EFI earlier

[Anthony PERARD <anthony.perard@xxxxxxxxxx>]

We are going to need the variable XEN_BUILD_EFI earlier.

But a side effect of calculating the value of $(XEN_BUILD_EFI) is to
also to generate "efi/check.o" which is used for further checks.
Thus the whole chain that check for EFI support is moved to
"arch.mk".

Some other changes are made to avoid too much duplication:
    - $(efi-check-o): Used to avoid repeating "efi/check.*". We don't
      set it to the path to the source as it would be wrong as soon
      as we support out-of-tree build.
    - $(LD_PE_check_cmd): As it is called twice, with an updated
      $(EFI_LDFLAGS).

$(nr-fixups) is renamed to $(efi-check-relocs) as the former might be
a bit too generic.

Signed-off-by: Anthony PERARD <anthony.perard@xxxxxxxxxx>
---

Notes:
    v7:
    - Do the whole check for EFI support in arch.mk. So efi/check.o is
      produce there and used there, and produce efi/check.efi and use it there.
      Thus avoid the need to repeat the test done for XEN_BUILD_EFI.

 xen/arch/x86/Makefile | 36 ++----------------------------------
 xen/arch/x86/arch.mk  | 42 ++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 44 insertions(+), 34 deletions(-)

diff --git a/xen/arch/x86/Makefile b/xen/arch/x86/Makefile
index 5e1d38d6cd5b..dfcbd01bb4ed 100644
--- a/xen/arch/x86/Makefile
+++ b/xen/arch/x86/Makefile
@@ -123,41 +123,7 @@ $(TARGET): $(TARGET)-syms $(efi-y) boot/mkelf32
        mv $(TMP) $(TARGET)
 
 ifneq ($(efi-y),)
-
-# Check if the compiler supports the MS ABI.
-export XEN_BUILD_EFI := $(shell $(CC) $(XEN_CFLAGS) -c efi/check.c -o 
efi/check.o 2>/dev/null && echo y)
 CFLAGS-$(XEN_BUILD_EFI) += -DXEN_BUILD_EFI
-
-# Check if the linker supports PE.
-EFI_LDFLAGS = $(patsubst -m%,-mi386pep,$(XEN_LDFLAGS)) --subsystem=10
-XEN_BUILD_PE := $(if $(XEN_BUILD_EFI),$(call ld-option,$(EFI_LDFLAGS) 
--image-base=0x100000000 -o efi/check.efi efi/check.o))
-# If the above failed, it may be merely because of the linker not dealing well
-# with debug info. Try again with stripping it.
-ifeq ($(CONFIG_DEBUG_INFO)-$(XEN_BUILD_PE),y-n)
-EFI_LDFLAGS += --strip-debug
-XEN_BUILD_PE := $(call ld-option,$(EFI_LDFLAGS) --image-base=0x100000000 -o 
efi/check.efi efi/check.o)
-endif
-
-ifeq ($(XEN_BUILD_PE),y)
-
-# Check if the linker produces fixups in PE by default
-nr-fixups := $(shell $(OBJDUMP) -p efi/check.efi | grep 
'^[[:blank:]]*reloc[[:blank:]]*[0-9][[:blank:]].*DIR64$$' | wc -l)
-ifeq ($(nr-fixups),2)
-MKRELOC := :
-relocs-dummy :=
-else
-MKRELOC := efi/mkreloc
-relocs-dummy := efi/relocs-dummy.o
-# If the linker produced fixups but not precisely two of them, we need to
-# disable it doing so.  But if it didn't produce any fixups, it also wouldn't
-# recognize the option.
-ifneq ($(nr-fixups),0)
-EFI_LDFLAGS += --disable-reloc-section
-endif
-endif
-
-endif # $(XEN_BUILD_PE)
-
 endif # $(efi-y)
 
 ALL_OBJS := $(BASEDIR)/arch/x86/boot/built_in.o 
$(BASEDIR)/arch/x86/efi/built_in.o $(ALL_OBJS)
@@ -218,8 +184,10 @@ endif
 
 $(TARGET).efi: VIRT_BASE = 0x$(shell $(NM) efi/relocs-dummy.o | sed -n 's, A 
VIRT_START$$,,p')
 ifeq ($(MKRELOC),:)
+relocs-dummy :=
 $(TARGET).efi: ALT_BASE :=
 else
+relocs-dummy := efi/relocs-dummy.o
 $(TARGET).efi: ALT_BASE = 0x$(shell $(NM) efi/relocs-dummy.o | sed -n 's, A 
ALT_START$$,,p')
 endif
 
diff --git a/xen/arch/x86/arch.mk b/xen/arch/x86/arch.mk
index eea320e618b9..98dd41d32118 100644
--- a/xen/arch/x86/arch.mk
+++ b/xen/arch/x86/arch.mk
@@ -60,5 +60,47 @@ ifeq ($(CONFIG_UBSAN),y)
 $(call cc-option-add,CFLAGS_UBSAN,CC,-fno-sanitize=alignment)
 endif
 
+ifneq ($(CONFIG_PV_SHIM_EXCLUSIVE),y)
+
+efi-check-o = arch/x86/efi/check.o
+
+# Check if the compiler supports the MS ABI.
+XEN_BUILD_EFI := $(call if-success,$(CC) $(CFLAGS) -c $(efi-check-o:.o=.c) -o 
$(efi-check-o),y)
+
+# Check if the linker supports PE.
+EFI_LDFLAGS := $(patsubst -m%,-mi386pep,$(LDFLAGS)) --subsystem=10
+LD_PE_check_cmd = $(call ld-option,$(EFI_LDFLAGS) --image-base=0x100000000 -o 
$(efi-check-o:.o=.efi) $(efi-check-o))
+XEN_BUILD_PE := $(LD_PE_check_cmd)
+
+# If the above failed, it may be merely because of the linker not dealing well
+# with debug info. Try again with stripping it.
+ifeq ($(CONFIG_DEBUG_INFO)-$(XEN_BUILD_PE),y-n)
+EFI_LDFLAGS += --strip-debug
+XEN_BUILD_PE := $(LD_PE_check_cmd)
+endif
+
+ifeq ($(XEN_BUILD_PE),y)
+
+# Check if the linker produces fixups in PE by default
+efi-check-relocs := $(shell $(OBJDUMP) -p $(efi-check-o:.o=.efi) | grep 
'^[[:blank:]]*reloc[[:blank:]]*[0-9][[:blank:]].*DIR64$$' | wc -l)
+
+ifeq ($(efi-check-relocs),2)
+MKRELOC := :
+else
+MKRELOC := efi/mkreloc
+# If the linker produced fixups but not precisely two of them, we need to
+# disable it doing so.  But if it didn't produce any fixups, it also wouldn't
+# recognize the option.
+ifneq ($(efi-check-relocs),0)
+EFI_LDFLAGS += --disable-reloc-section
+endif
+endif
+
+endif # $(XEN_BUILD_PE)
+
+export XEN_BUILD_EFI XEN_BUILD_PE MKRELOC
+export EFI_LDFLAGS
+endif
+
 # Set up the assembler include path properly for older toolchains.
 CFLAGS += -Wa,-I$(BASEDIR)/include
-- 
Anthony PERARD