[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [PATCH v5 09/10] xen/arm: Do not map PCI ECAM and MMIO space to Domain-0's p2m



On Fri, 8 Oct 2021, Oleksandr Andrushchenko wrote:
> From: Oleksandr Andrushchenko <oleksandr_andrushchenko@xxxxxxxx>
> 
> PCI host bridges are special devices in terms of implementing PCI
> passthrough. According to [1] the current implementation depends on
> Domain-0 to perform the initialization of the relevant PCI host
> bridge hardware and perform PCI device enumeration. In order to
> achieve that one of the required changes is to not map all the memory
> ranges in map_range_to_domain as we traverse the device tree on startup
> and perform some additional checks if the range needs to be mapped to
> Domain-0.
> 
> The generic PCI host controller device tree binding says [2]:
> - ranges: As described in IEEE Std 1275-1994, but must provide
>           at least a definition of non-prefetchable memory. One
>           or both of prefetchable Memory and IO Space may also
>           be provided.
> 
> - reg   : The Configuration Space base address and size, as accessed
>           from the parent bus.  The base address corresponds to
>           the first bus in the "bus-range" property.  If no
>           "bus-range" is specified, this will be bus 0 (the default).
> 
> >From the above none of the memory ranges from the "ranges" property
> needs to be mapped to Domain-0 at startup as MMIO mapping is going to
> be handled dynamically by vPCI as we assign PCI devices, e.g. each
> device assigned to Domain-0/guest will have its MMIOs mapped/unmapped
> as needed by Xen.
> 
> The "reg" property covers not only ECAM space, but may also have other
> then the configuration memory ranges described, for example [3]:
> - reg: Should contain rc_dbi, config registers location and length.
> - reg-names: Must include the following entries:
>    "rc_dbi": controller configuration registers;
>    "config": PCIe configuration space registers.
> 
> This patch makes it possible to not map all the ranges from the
> "ranges" property and also ECAM from the "reg". All the rest from the
> "reg" property still needs to be mapped to Domain-0, so the PCI
> host bridge remains functional in Domain-0.
> 
> [1] https://lists.xenproject.org/archives/html/xen-devel/2020-07/msg00777.html
> [2] 
> https://www.kernel.org/doc/Documentation/devicetree/bindings/pci/host-generic-pci.txt
> [3] 
> https://www.kernel.org/doc/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt
> 
> Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@xxxxxxxx>

Reviewed-by: Stefano Stabellini <sstabellini@xxxxxxxxxx>


> ---
> Since v4:
> - update skip_mapping comment
> - add comment why we need to map interrupts to Dom0
> Since v3:
>  - pass struct map_range_data to map_dt_irq_to_domain
>  - remove redundant check from map_range_to_domain
>  - fix handle_device's .skip_mapping
> Since v2:
>  - removed check in map_range_to_domain for PCI_DEV
>    and moved it to handle_device, so the code is
>    simpler
>  - s/map_pci_bridge/skip_mapping
>  - extended comment in pci_host_bridge_mappings
>  - minor code restructure in construct_dom0
>  - s/.need_p2m_mapping/.need_p2m_hwdom_mapping and related
>    callbacks
>  - unsigned int i; in pci_host_bridge_mappings
> Since v1:
>  - Added better description of why and what needs to be mapped into
>    Domain-0's p2m and what doesn't
>  - Do not do any mappings for PCI devices while traversing the DT
>  - Walk all the bridges and make required mappings in one go
> ---
>  xen/arch/arm/domain_build.c        | 57 ++++++++++++++++++------------
>  xen/arch/arm/pci/ecam.c            | 14 ++++++++
>  xen/arch/arm/pci/pci-host-common.c | 49 +++++++++++++++++++++++++
>  xen/arch/arm/pci/pci-host-zynqmp.c |  1 +
>  xen/include/asm-arm/pci.h          | 10 ++++++
>  xen/include/asm-arm/setup.h        | 13 +++++++
>  6 files changed, 121 insertions(+), 23 deletions(-)
> 
> diff --git a/xen/arch/arm/domain_build.c b/xen/arch/arm/domain_build.c
> index b51176b31bef..0d673b06a2f3 100644
> --- a/xen/arch/arm/domain_build.c
> +++ b/xen/arch/arm/domain_build.c
> @@ -10,7 +10,6 @@
>  #include <asm/regs.h>
>  #include <xen/errno.h>
>  #include <xen/err.h>
> -#include <xen/device_tree.h>
>  #include <xen/libfdt/libfdt.h>
>  #include <xen/guest_access.h>
>  #include <xen/iocap.h>
> @@ -51,12 +50,6 @@ static int __init parse_dom0_mem(const char *s)
>  }
>  custom_param("dom0_mem", parse_dom0_mem);
>  
> -struct map_range_data
> -{
> -    struct domain *d;
> -    p2m_type_t p2mt;
> -};
> -
>  /* Override macros from asm/page.h to make them work with mfn_t */
>  #undef virt_to_mfn
>  #define virt_to_mfn(va) _mfn(__virt_to_mfn(va))
> @@ -1663,10 +1656,11 @@ static int __init map_dt_irq_to_domain(const struct 
> dt_device_node *dev,
>                                         const struct dt_irq *dt_irq,
>                                         void *data)
>  {
> -    struct domain *d = data;
> +    struct map_range_data *mr_data = data;
> +    struct domain *d = mr_data->d;
>      unsigned int irq = dt_irq->irq;
>      int res;
> -    bool need_mapping = !dt_device_for_passthrough(dev);
> +    bool need_mapping = !mr_data->skip_mapping;
>  
>      if ( irq < NR_LOCAL_IRQS )
>      {
> @@ -1690,13 +1684,12 @@ static int __init map_dt_irq_to_domain(const struct 
> dt_device_node *dev,
>      return 0;
>  }
>  
> -static int __init map_range_to_domain(const struct dt_device_node *dev,
> -                                      u64 addr, u64 len,
> -                                      void *data)
> +int __init map_range_to_domain(const struct dt_device_node *dev,
> +                               u64 addr, u64 len, void *data)
>  {
>      struct map_range_data *mr_data = data;
>      struct domain *d = mr_data->d;
> -    bool need_mapping = !dt_device_for_passthrough(dev);
> +    bool need_mapping = !mr_data->skip_mapping;
>      int res;
>  
>      /*
> @@ -1748,23 +1741,21 @@ static int __init map_range_to_domain(const struct 
> dt_device_node *dev,
>   * then we may need to perform additional mappings in order to make
>   * the child resources available to domain 0.
>   */
> -static int __init map_device_children(struct domain *d,
> -                                      const struct dt_device_node *dev,
> -                                      p2m_type_t p2mt)
> +static int __init map_device_children(const struct dt_device_node *dev,
> +                                      struct map_range_data *mr_data)
>  {
> -    struct map_range_data mr_data = { .d = d, .p2mt = p2mt };
> -    int ret;
> -
>      if ( dt_device_type_is_equal(dev, "pci") )
>      {
> +        int ret;
> +
>          dt_dprintk("Mapping children of %s to guest\n",
>                     dt_node_full_name(dev));
>  
> -        ret = dt_for_each_irq_map(dev, &map_dt_irq_to_domain, d);
> +        ret = dt_for_each_irq_map(dev, &map_dt_irq_to_domain, mr_data);
>          if ( ret < 0 )
>              return ret;
>  
> -        ret = dt_for_each_range(dev, &map_range_to_domain, &mr_data);
> +        ret = dt_for_each_range(dev, &map_range_to_domain, mr_data);
>          if ( ret < 0 )
>              return ret;
>      }
> @@ -1845,6 +1836,20 @@ static int __init handle_device(struct domain *d, 
> struct dt_device_node *dev,
>      int res;
>      u64 addr, size;
>      bool need_mapping = !dt_device_for_passthrough(dev);
> +    /*
> +     * For PCI passthrough we only need to remap to Dom0 the interrupts
> +     * and memory ranges from "reg" property which cover controller's
> +     * configuration registers and such. PCIe configuration space registers
> +     * of the PCIe Root Complex and PCIe aperture should not be mapped
> +     * automatically to Dom0.
> +     */
> +    struct map_range_data mr_data = {
> +        .d = d,
> +        .p2mt = p2mt,
> +        .skip_mapping = !need_mapping ||
> +                        (is_pci_passthrough_enabled() &&
> +                         (device_get_class(dev) == DEVICE_PCI))
> +    };
>  
>      naddr = dt_number_of_address(dev);
>  
> @@ -1884,7 +1889,6 @@ static int __init handle_device(struct domain *d, 
> struct dt_device_node *dev,
>      /* Give permission and map MMIOs */
>      for ( i = 0; i < naddr; i++ )
>      {
> -        struct map_range_data mr_data = { .d = d, .p2mt = p2mt };
>          res = dt_device_get_address(dev, i, &addr, &size);
>          if ( res )
>          {
> @@ -1898,7 +1902,7 @@ static int __init handle_device(struct domain *d, 
> struct dt_device_node *dev,
>              return res;
>      }
>  
> -    res = map_device_children(d, dev, p2mt);
> +    res = map_device_children(dev, &mr_data);
>      if ( res )
>          return res;
>  
> @@ -3056,7 +3060,14 @@ static int __init construct_dom0(struct domain *d)
>          return rc;
>  
>      if ( acpi_disabled )
> +    {
>          rc = prepare_dtb_hwdom(d, &kinfo);
> +        if ( rc < 0 )
> +            return rc;
> +#ifdef CONFIG_HAS_PCI
> +        rc = pci_host_bridge_mappings(d, p2m_mmio_direct_c);
> +#endif
> +    }
>      else
>          rc = prepare_acpi(d, &kinfo);
>  
> diff --git a/xen/arch/arm/pci/ecam.c b/xen/arch/arm/pci/ecam.c
> index 602d00799c8d..b81620074a91 100644
> --- a/xen/arch/arm/pci/ecam.c
> +++ b/xen/arch/arm/pci/ecam.c
> @@ -40,6 +40,19 @@ void __iomem *pci_ecam_map_bus(struct pci_host_bridge 
> *bridge,
>      return base + (PCI_DEVFN2(sbdf.bdf) << devfn_shift) + where;
>  }
>  
> +bool pci_ecam_need_p2m_hwdom_mapping(struct domain *d,
> +                                     struct pci_host_bridge *bridge,
> +                                     uint64_t addr)
> +{
> +    struct pci_config_window *cfg = bridge->cfg;
> +
> +    /*
> +     * We do not want ECAM address space to be mapped in Domain-0's p2m,
> +     * so we can trap access to it.
> +     */
> +    return cfg->phys_addr != addr;
> +}
> +
>  /* ECAM ops */
>  const struct pci_ecam_ops pci_generic_ecam_ops = {
>      .bus_shift  = 20,
> @@ -47,6 +60,7 @@ const struct pci_ecam_ops pci_generic_ecam_ops = {
>          .map_bus                = pci_ecam_map_bus,
>          .read                   = pci_generic_config_read,
>          .write                  = pci_generic_config_write,
> +        .need_p2m_hwdom_mapping = pci_ecam_need_p2m_hwdom_mapping,
>      }
>  };
>  
> diff --git a/xen/arch/arm/pci/pci-host-common.c 
> b/xen/arch/arm/pci/pci-host-common.c
> index 1eb4daa87365..085f08e23e0c 100644
> --- a/xen/arch/arm/pci/pci-host-common.c
> +++ b/xen/arch/arm/pci/pci-host-common.c
> @@ -18,6 +18,7 @@
>  
>  #include <xen/init.h>
>  #include <xen/pci.h>
> +#include <asm/setup.h>
>  #include <xen/rwlock.h>
>  #include <xen/sched.h>
>  #include <xen/vmap.h>
> @@ -320,6 +321,54 @@ int pci_host_get_num_bridges(void)
>      return count;
>  }
>  
> +int __init pci_host_bridge_mappings(struct domain *d, p2m_type_t p2mt)
> +{
> +    struct pci_host_bridge *bridge;
> +    struct map_range_data mr_data = {
> +        .d = d,
> +        .p2mt = p2mt,
> +        .skip_mapping = false
> +    };
> +
> +    /*
> +     * For each PCI host bridge we need to only map those ranges
> +     * which are used by Domain-0 to properly initialize the bridge,
> +     * e.g. we do not want to map ECAM configuration space which lives in
> +     * "reg" or "assigned-addresses" device tree property, but we want to
> +     * map other regions of the host bridge. The PCI aperture defined by
> +     * the "ranges" device tree property should also be skipped.
> +     */
> +    list_for_each_entry( bridge, &pci_host_bridges, node )
> +    {
> +        const struct dt_device_node *dev = bridge->dt_node;
> +        unsigned int i;
> +
> +        for ( i = 0; i < dt_number_of_address(dev); i++ )
> +        {
> +            uint64_t addr, size;
> +            int err;
> +
> +            err = dt_device_get_address(dev, i, &addr, &size);
> +            if ( err )
> +            {
> +                printk(XENLOG_ERR
> +                       "Unable to retrieve address range index=%u for %s\n",
> +                       i, dt_node_full_name(dev));
> +                return err;
> +            }
> +
> +            if ( bridge->ops->need_p2m_hwdom_mapping(d, bridge, addr) )
> +            {
> +                err = map_range_to_domain(dev, addr, size, &mr_data);
> +                if ( err )
> +                    return err;
> +            }
> +        }
> +    }
> +
> +    return 0;
> +}
> +
>  /*
>   * Local variables:
>   * mode: C
> diff --git a/xen/arch/arm/pci/pci-host-zynqmp.c 
> b/xen/arch/arm/pci/pci-host-zynqmp.c
> index 61a9807d3d58..6ad2b31e810d 100644
> --- a/xen/arch/arm/pci/pci-host-zynqmp.c
> +++ b/xen/arch/arm/pci/pci-host-zynqmp.c
> @@ -34,6 +34,7 @@ const struct pci_ecam_ops nwl_pcie_ops = {
>          .map_bus                = pci_ecam_map_bus,
>          .read                   = pci_generic_config_read,
>          .write                  = pci_generic_config_write,
> +        .need_p2m_hwdom_mapping = pci_ecam_need_p2m_hwdom_mapping,
>      }
>  };
>  
> diff --git a/xen/include/asm-arm/pci.h b/xen/include/asm-arm/pci.h
> index a71b0eea8cb9..b5b85ccd0937 100644
> --- a/xen/include/asm-arm/pci.h
> +++ b/xen/include/asm-arm/pci.h
> @@ -17,6 +17,8 @@
>  
>  #ifdef CONFIG_HAS_PCI
>  
> +#include <asm/p2m.h>
> +
>  #define pci_to_dev(pcidev) (&(pcidev)->arch.dev)
>  
>  extern bool pci_passthrough_enabled;
> @@ -73,6 +75,9 @@ struct pci_ops {
>                  uint32_t reg, uint32_t len, uint32_t *value);
>      int (*write)(struct pci_host_bridge *bridge, pci_sbdf_t sbdf,
>                   uint32_t reg, uint32_t len, uint32_t value);
> +    bool (*need_p2m_hwdom_mapping)(struct domain *d,
> +                                   struct pci_host_bridge *bridge,
> +                                   uint64_t addr);
>  };
>  
>  /*
> @@ -96,6 +101,9 @@ int pci_generic_config_write(struct pci_host_bridge 
> *bridge, pci_sbdf_t sbdf,
>                               uint32_t reg, uint32_t len, uint32_t value);
>  void __iomem *pci_ecam_map_bus(struct pci_host_bridge *bridge,
>                                 pci_sbdf_t sbdf, uint32_t where);
> +bool pci_ecam_need_p2m_hwdom_mapping(struct domain *d,
> +                                     struct pci_host_bridge *bridge,
> +                                     uint64_t addr);
>  struct pci_host_bridge *pci_find_host_bridge(uint16_t segment, uint8_t bus);
>  int pci_get_host_bridge_segment(const struct dt_device_node *node,
>                                  uint16_t *segment);
> @@ -113,6 +121,8 @@ int pci_host_iterate_bridges(struct domain *d,
>                                          struct pci_host_bridge *bridge));
>  int pci_host_get_num_bridges(void);
>  
> +int pci_host_bridge_mappings(struct domain *d, p2m_type_t p2mt);
> +
>  #else   /*!CONFIG_HAS_PCI*/
>  
>  struct arch_pci_dev { };
> diff --git a/xen/include/asm-arm/setup.h b/xen/include/asm-arm/setup.h
> index 95da0b7ab9cd..88d9673db817 100644
> --- a/xen/include/asm-arm/setup.h
> +++ b/xen/include/asm-arm/setup.h
> @@ -2,6 +2,8 @@
>  #define __ARM_SETUP_H_
>  
>  #include <public/version.h>
> +#include <asm/p2m.h>
> +#include <xen/device_tree.h>
>  
>  #define MIN_FDT_ALIGN 8
>  #define MAX_FDT_SIZE SZ_2M
> @@ -77,6 +79,14 @@ struct bootinfo {
>  #endif
>  };
>  
> +struct map_range_data
> +{
> +    struct domain *d;
> +    p2m_type_t p2mt;
> +    /* Set if mapping of the memory ranges must be skipped. */
> +    bool skip_mapping;
> +};
> +
>  extern struct bootinfo bootinfo;
>  
>  extern domid_t max_init_domid;
> @@ -124,6 +134,9 @@ void device_tree_get_reg(const __be32 **cell, u32 
> address_cells,
>  u32 device_tree_get_u32(const void *fdt, int node,
>                          const char *prop_name, u32 dflt);
>  
> +int map_range_to_domain(const struct dt_device_node *dev,
> +                        u64 addr, u64 len, void *data);
> +
>  #endif
>  /*
>   * Local variables:
> -- 
> 2.25.1
> 



 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.