Re: [PATCH V3 3/6] libxl: arm: Create alloc_virtio_mmio_params()

[Oleksandr <olekstysh@xxxxxxxxx>]

On 04.08.22 10:01, Viresh Kumar wrote:

Hello Viresh


> Create a separate routine to allocate base and irq for a device as the
> same code will be required for each device type.
>
> Suggested-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@xxxxxxxx>
> Signed-off-by: Viresh Kumar <viresh.kumar@xxxxxxxxxx>
> ---
>   tools/libs/light/libxl_arm.c | 38 ++++++++++++++++++++++++------------
>   1 file changed, 25 insertions(+), 13 deletions(-)
>
> diff --git a/tools/libs/light/libxl_arm.c b/tools/libs/light/libxl_arm.c
> index 1a3ac1646e94..2f64b9f0ebee 100644
> --- a/tools/libs/light/libxl_arm.c
> +++ b/tools/libs/light/libxl_arm.c
> @@ -48,6 +48,24 @@ static uint32_t alloc_virtio_mmio_irq(libxl__gc *gc, 
> uint32_t *virtio_mmio_irq)
>       return irq;
>   }
>   
> +static int alloc_virtio_mmio_params(libxl__gc *gc, uint64_t *base,
> +                                    uint32_t *irq, uint64_t *virtio_mmio_base,
> +                                    uint32_t *virtio_mmio_irq)
> +{
> +    *base = alloc_virtio_mmio_base(gc, virtio_mmio_base);
> +    if (!*base)
> +        return ERROR_FAIL;
> +
> +    *irq = alloc_virtio_mmio_irq(gc, virtio_mmio_irq);
> +    if (!*irq)
> +        return ERROR_FAIL;
> +
> +    LOG(DEBUG, "Allocate Virtio MMIO params: IRQ %u BASE 0x%"PRIx64, *irq,
> +        *base);
> +
> +    return 0;
> +}
> +
>   static const char *gicv_to_string(libxl_gic_version gic_version)
>   {
>       switch (gic_version) {
> @@ -85,20 +103,12 @@ int libxl__arch_domain_prepare_config(libxl__gc *gc,
>           libxl_device_disk *disk = &d_config->disks[i];
>   
>           if (disk->specification == LIBXL_DISK_SPECIFICATION_VIRTIO) {
> -            disk->base = alloc_virtio_mmio_base(gc, &virtio_mmio_base);
> -            if (!disk->base)
> -                return ERROR_FAIL;
> +            int rc = alloc_virtio_mmio_params(gc, &disk->base, &disk->irq,
> +                    &virtio_mmio_base, &virtio_mmio_irq);
> +            if (rc)
> +                return rc;
>   
> -            disk->irq = alloc_virtio_mmio_irq(gc, &virtio_mmio_irq);
> -            if (!disk->irq)
> -                return ERROR_FAIL;
> -
> -            if (virtio_irq < disk->irq)
> -                virtio_irq = disk->irq;
>               virtio_enabled = true;
   I think that "virtio_enabled = true;" should be moved ...


> -
> -            LOG(DEBUG, "Allocate Virtio MMIO params for Vdev %s: IRQ %u BASE 
> 0x%"PRIx64,
> -                disk->vdev, disk->irq, disk->base);
>           }
>       }
>   
> @@ -107,8 +117,10 @@ int libxl__arch_domain_prepare_config(libxl__gc *gc,
>        * present, make sure that we allocate enough SPIs for them.
>        * The resulting "nr_spis" needs to cover the highest possible SPI.
>        */
> -    if (virtio_enabled)
> +    if (virtio_mmio_irq != GUEST_VIRTIO_MMIO_SPI_FIRST) {
> +        virtio_irq = virtio_mmio_irq - 1;
>           nr_spis = max(nr_spis, virtio_irq - 32 + 1);
 ... here. Otherwise after applying all patches "virtio_enabled" only 
gets set if there is a virtio disk device. So it won't be set for virtio 
i2c, etc.
I see that in V2 it was there, but in V3 is not. Or maybe there is some 
reason for doing that which I am not aware of?

Other changes look good.


> +    }
>   
>       for (i = 0; i < d_config->b_info.num_irqs; i++) {
>           uint32_t irq = d_config->b_info.irqs[i];
--
Regards,

Oleksandr Tyshchenko