[PATCH v7 2/2] drivers/char: Use sub-page ro API to make just xhci dbc cap RO

[Marek Marczykowski-Górecki <marmarek@xxxxxxxxxxxxxxxxxxxxxx>]

Not the whole page, which may contain other registers too. The XHCI
specification describes DbC as designed to be controlled by a different
driver, but does not mandate placing registers on a separate page. In fact
on Tiger Lake and newer (at least), this page do contain other registers
that Linux tries to use. And with share=yes, a domU would use them too.
Without this patch, PV dom0 would fail to initialize the controller,
while HVM would be killed on EPT violation.

With `share=yes`, this patch gives domU more access to the emulator
(although a HVM with any emulated device already has plenty of it). This
configuration is already documented as unsafe with untrusted guests and
not security supported.

Signed-off-by: Marek Marczykowski-Górecki <marmarek@xxxxxxxxxxxxxxxxxxxxxx>
Reviewed-by: Jan Beulich <jbeulich@xxxxxxxx>
---
Changes in v4:
- restore mmio_ro_ranges in the fallback case
- set XHCI_SHARE_NONE in the fallback case
Changes in v3:
- indentation fix
- remove stale comment
- fallback to pci_ro_device() if subpage_mmio_ro_add() fails
- extend commit message
Changes in v2:
 - adjust for simplified subpage_mmio_ro_add() API
---
 xen/drivers/char/xhci-dbc.c | 36 ++++++++++++++++++++++--------------
 1 file changed, 22 insertions(+), 14 deletions(-)

diff --git a/xen/drivers/char/xhci-dbc.c b/xen/drivers/char/xhci-dbc.c
index 8e2037f1a5f7..c45e4b6825cc 100644
--- a/xen/drivers/char/xhci-dbc.c
+++ b/xen/drivers/char/xhci-dbc.c
@@ -1216,20 +1216,28 @@ static void __init cf_check 
dbc_uart_init_postirq(struct serial_port *port)
         break;
     }
 #ifdef CONFIG_X86
-    /*
-     * This marks the whole page as R/O, which may include other registers
-     * unrelated to DbC. Xen needs only DbC area protected, but it seems
-     * Linux's XHCI driver (as of 5.18) works without writting to the whole
-     * page, so keep it simple.
-     */
-    if ( rangeset_add_range(mmio_ro_ranges,
-                PFN_DOWN((uart->dbc.bar_val & PCI_BASE_ADDRESS_MEM_MASK) +
-                         uart->dbc.xhc_dbc_offset),
-                PFN_UP((uart->dbc.bar_val & PCI_BASE_ADDRESS_MEM_MASK) +
-                       uart->dbc.xhc_dbc_offset +
-                sizeof(*uart->dbc.dbc_reg)) - 1) )
-        printk(XENLOG_INFO
-               "Error while adding MMIO range of device to mmio_ro_ranges\n");
+    if ( subpage_mmio_ro_add(
+             (uart->dbc.bar_val & PCI_BASE_ADDRESS_MEM_MASK) +
+              uart->dbc.xhc_dbc_offset,
+             sizeof(*uart->dbc.dbc_reg)) )
+    {
+        printk(XENLOG_WARNING
+               "Error while marking MMIO range of XHCI console as R/O, "
+               "making the whole device R/O (share=no)\n");
+        uart->dbc.share = XHCI_SHARE_NONE;
+        if ( pci_ro_device(0, uart->dbc.sbdf.bus, uart->dbc.sbdf.devfn) )
+            printk(XENLOG_WARNING
+                   "Failed to mark read-only %pp used for XHCI console\n",
+                   &uart->dbc.sbdf);
+        if ( rangeset_add_range(mmio_ro_ranges,
+                 PFN_DOWN((uart->dbc.bar_val & PCI_BASE_ADDRESS_MEM_MASK) +
+                          uart->dbc.xhc_dbc_offset),
+                 PFN_UP((uart->dbc.bar_val & PCI_BASE_ADDRESS_MEM_MASK) +
+                        uart->dbc.xhc_dbc_offset +
+                        sizeof(*uart->dbc.dbc_reg)) - 1) )
+            printk(XENLOG_INFO
+                   "Error while adding MMIO range of device to 
mmio_ro_ranges\n");
+    }
 #endif
 }
 
-- 
git-series 0.9.1