Re: [Xen-users] domU network doesn't get IP

[Jayesh Salvi <jayeshsalvi@xxxxxxxxx>]

And yes I am using Xen 3.0

On 1/3/06, Jayesh Salvi <jayeshsalvi@xxxxxxxxx> wrote:

OK. Now both firewall and SELinux are disabled. I created a domU with MAC AA:00:00:00:00:11.
Then I did manual configuration of eth0 as you told.
Here is the trace:
[root@localhost ~]# ifconfig
eth0      Link encap:Ethernet  HWaddr AA:00:00:00:00:11
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:895 errors:0 dropped:0 overruns:0 frame:0
          TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:58557 (57.1 KiB)  TX bytes:2394 (2.3 KiB)

lo        Link encap:Local Loopback
          inet addr: 127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:8 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:560 (560.0 b)  TX bytes:560 (560.0 b)

[root@localhost ~]# ifconfig eth0 192.168.1.1 netmask 255.255.255.0
[root@localhost ~]# ifconfig eth0 up
[root@localhost ~]# ifconfig
eth0      Link encap:Ethernet  HWaddr AA:00:00:00:00:11
          inet addr:192.168.1.1  Bcast: 192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:1191 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:78311 (76.4 KiB)  TX bytes:2436 (2.3 KiB)

lo        Link encap:Local Loopback
          inet addr: 127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:8 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:560 (560.0 b)  TX bytes:560 (560.0 b)


Even after this I can't see dom0 from domU. My dom0's IP is 24.118.198.46

So when I ping my dom0 from domU, I can't reach it:
[root@localhost ~]# ping 24.118.198.46
connect: Network is unreachable

When I ping the IP address 192.168.1.1 from dom0, I get
[root@orion xen]# ping 192.168.1.1
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
From 10.230.64.1 icmp_seq=3 Packet filtered
From 10.230.64.1 icmp_seq=6 Packet filtered
From 10.230.64.1 icmp_seq=8 Packet filtered

--- 192.168.1.1 ping statistics ---
11 packets transmitted, 0 received, +3 errors, 100% packet loss, time 10137ms
, pipe 2

Thanks Anand for your suggestions so far.

I want to clarify few more thing:
In my domain config file, I now set mac address myself, instead of default.  So my vif is now:
vif = [ 'mac=aa:00:00:00:00:11, bridge=xenbr0' ]
What about DHCP option? Should I turn it on/off? I tried it both ways, but that didn't help - my dom0 gets its IP by DHCP from my ISP provider.
I don't set nics, because by default it is 1.
I also don't set netmask, gateway, hostname in my domain config file. Should I set these variables?

Let me know.
Thanks,
Jayesh

On 1/3/06, Anand <xen.mails@xxxxxxxxx> wrote:

Make sure your firewall is disabled. Disable selinux.

Manual configuration of eth0 can be done as follows:

ifconfig eth0 192.168.1.1 netmask 255.255.255.0

ifconfig eth0 up

Now try to ping the interface.

Which version of xen are you using ?

On 1/3/06, Jayesh Salvi < jayeshsalvi@xxxxxxxxx> wrote:

> Try to manually configure the eth0 inside domU and see if it helps.
Sorry, I don't know exactly how to do it. Could you elaborate on how to manually configure eth0?

Thanks for pointing out the custom mac address question.

Can anyone tell me about these error messages from xend-hotplug.log

xenstore-read: couldn't read path backend/vbd/5/777/physical

-device
xenstore-read: couldn't read path backend/vif/5/0/ip
xenstore-read: couldn't read path backend/vif/5/0/bridge
xenstore-read: couldn't read path backend/vbd/5/777/physical-device
[After I shutdown the domain I further get]
xenstore-read: couldn't read path backend/vif/5/0/ip
xenstore-read: couldn't read path backend/vif/5/0/bridge
interface vif5.0 does not exist!

I think "couldn't read path backend/vif/5/0/ip "  should really have to do with this IP problem. But I don't understand which path is this? Is it  a path somewhere on root file system?

On 1/3/06, Anand < xen.mails@xxxxxxxxx> wrote:

>I have started domU successfully. I am using the default xend-config.sxp, it uses >(network-script network-bridge). But my domU doesn't get any IP information, and it's >disconnected from dom0 and rest of the world.

Try to manually configure the eth0 inside domU and see if it helps.

>(Also I don't understand where the domU gets its MAC address 00:16:3E:56:79:71? Could >anyone explain that as well?)

You can setup a custom mac address by using the option vif = ['mac=FF:FE:00:18:98:FB, bridge=xenbr0'] inside the domU config file. Substitute the mac address after the mac= for the desired mac address.

--

regards,

Anand

--
Jayesh

--

regards,

Anand

--
Jayesh

-- 
Jayesh

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users