Re: [Xen-users] Building asterisk@home domU manually?

["Ryan Burke" <burke@xxxxxxxxxxxxxxxxx>]

John,

Thanks for the info. I have Asterisk 1.2.6 running just fine with only VoIP. 
The problem I had was getting the Zaptel hardware detected in the DomU. I 
never figured it out. But if I load a Dom0 then it works. So it is possible, 
I was just looking for a way to do it in a non-privileged DomU.
Ryan

----- Original Message ----- 
From: "John Cianfarani" <jcianfarani@xxxxxxxxxx>
To: "David Muench" <davemuench@xxxxxxxxx>; "Ryan Burke" 
<burke@xxxxxxxxxxxxxxxxx>
Cc: <xen-users@xxxxxxxxxxxxxxxxxxx>
Sent: Saturday, April 08, 2006 11:40 AM
Subject: RE: [Xen-users] Building asterisk@home domU manually?


I've gone the same route as you dave and using only ztdummy.
To do this and make it work you also need to recompile the Dom0/U kernel
for 1000hz timing.

Dave do you notice any small chops in the voice quality? Have you had to
change sched-sedf parameters?


Ryan it should be pretty easy to install the A@H into a DomU.  Once you
get a domU running (preferably CentOS since that's what A@H uses) make
sure the GPG key is installed with "rpm --import
/usr/share/doc/centos-release-4/RPM-GPG-KEY" and make sure you can
install update packages with yum.

Then just download the tar.gz a@h file instead of the .iso file.  Inside
the .tar.gz the ReleaseNotes.txt shows instructions

Here is a brief copy and paste:

disable SELINUX (edit /etc/selinux/config)

Make a directory to install from and put the install file there
  mkdir /var/aah_load
  cp asteriskathome-2.7.tar.gz /var/aah_load
  cd /var/aah_load

Untar the file install file
  tar xvfz asteriskathome-2.7.tar.gz

Install
  ./install.sh


Hope that helps

Thanks
John Cianfarani

-----Original Message-----
From: xen-users-bounces@xxxxxxxxxxxxxxxxxxx
[mailto:xen-users-bounces@xxxxxxxxxxxxxxxxxxx] On Behalf Of David Muench
Sent: Saturday, April 08, 2006 11:19 AM
To: Ryan Burke
Cc: xen-users@xxxxxxxxxxxxxxxxxxx
Subject: Re: [Xen-users] Building asterisk@home domU manually?

On 4/8/06, Ryan Burke <burke@xxxxxxxxxxxxxxxxx> wrote:
> Are you using any Zaptel hardware in your Asterisk install?
No, and I think that may be part of the key to my success with it. I
am using the ztdummy driver though. I'm also still using Xen 2.0.7.
Haven't had time to try out 3.0.2 yet. I am going to need a FXS port
in the near future, and I'm torn between trying to get a FXS card to
work vs. getting an ATA like device to stay away from the zaptel
drivers.

I can't recall seeing anyone successfully using zaptel hardware under
xen in a domU, but I might of just missed it.

Dave

--
David Muench - davemuench@xxxxxxxxx
Jabber/Google Talk: davemuench@xxxxxxxxx

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users



_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users 

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users