Re: [Xen-users] two bridges with xen 3.2.0

[Jordi Moles <jordi@xxxxxxxxx>]

Hi again,

... and more importantly...

what about the conf files in the virtual machines?

something like...

vif=[ 'bridge=eth0', 'bridge=eth1' ]

??????'

thank you.

En/na Jordi Moles ha escrit:
> Hi,
>
> i'm sorry guys, i don't quite get it.
>
> i replaced my script with this one:
>
> ***********
>
> #!/bin/sh
> XENDIR="/etc/xen/scripts"
>
> $XENDIR/network-bridge "$@" netdev=eth0 bridge=eth0 vifnum=0
> $XENDIR/network-bridge "$@" netdev=eth1 bridge=eth1 vifnum=1
>
>
> ***********
>
> on the other hand....
>
> what about /etc/xen/xend-config.sxp ? Do i have to keep the 
> (vif-script vif-bridge) line? Do i have to use another script?
> what about /etc/network/interfaces? can i use something like this?
>
> ****************
> auto lo
> iface lo inet loopback
>
> auto eth0
> iface eth0 inet static
>        address 192.168.1.200
>        netmask 255.255.255.0
>        network 192.168.1.0
>        broadcast 192.168.1.255
>        gateway 192.168.1.231
>
> auto eth1
> iface eth1 inet static
>        address 192.168.2.200
>        netmask 255.255.255.0
>
> ****************
>
> or do i have to replace eth0 with peth0 in this file? will debian load 
> the newtork interfaces if i change the name?
> Thank you.
>
> En/na Gareth Bult ha escrit:
> > Hi,
> >
> > Here's my Xen3.2 script .. working 100% on multiple boxes ...
> >
> > #!/bin/sh
> > XENDIR="/etc/xen/scripts"
> >
> > $XENDIR/network-bridge "$@" netdev=eth0 bridge=eth0 vifnum=0
> > $XENDIR/network-bridge "$@" netdev=eth1 bridge=eth1 vifnum=1
> >
> > NOTE::
> >
> > The nice people at Xen changed the default bridge from Xenbr<n> to 
> > eth<n>.
> > New method;
> > a. rename device eth0 to peth0
> > b. create a bridge called eth0 (!!)
> > c. include peth0 as a device for bridge eth0
> >
> > !!
> >
> > Much improved method, however, the documentation stinks ..
> >
> > Gareth.
> >
> >
> > ----- Original Message -----
> > step 3.: "Jordi Moles" <jordi@xxxxxxxxx>
> > To: xen-users@xxxxxxxxxxxxxxxxxxx
> > Sent: 20 February 2008 11:50:33 o'clock (GMT) Europe/London
> > Subject: [Xen-users] two bridges with xen 3.2.0
> >
> > hi,
> >
> > i'm trying the new 3.2.0.
> >
> > i've always used two bridges since 3.0.x with the following set up:
> >
> > Replace
> >
> > (network-script network-bridge)
> >
> > with
> >
> > (network-script network-bridge-both)
> >
> > in file /etc/xen/xend-config.sxp
> >
> > The content of network-bridge-both is
> >
> > ************
> >
> > #!/bin/sh
> > dir=$(dirname "$0")
> > "$dir/network-bridge" "$@" vifnum=0 netdev=eth0 bridge=xenbr0
> > "$dir/network-bridge" "$@" vifnum=1 netdev=eth1 bridge=xenbr1
> >
> > ************
> >
> > As i said, this used to work for 3.0.x and 3.1.x releases.....
> >
> > Now, it doesn't work anymore...
> >
> > when the xen loads....
> >
> > there's only this in the ifconfig command:
> >
> > -lo
> > -peth0
> > -peth1
> >
> > What's different from the earlier releases? Thank you.
> >
> > _______________________________________________
> > Xen-users mailing list
> > Xen-users@xxxxxxxxxxxxxxxxxxx
> > http://lists.xensource.com/xen-users
> >
> > _______________________________________________
> > Xen-users mailing list
> > Xen-users@xxxxxxxxxxxxxxxxxxx
> > http://lists.xensource.com/xen-users
> >   
>
> _______________________________________________
> Xen-users mailing list
> Xen-users@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-users

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users