[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-users] Simple question about Para-virtualized drivers in Windows


  • To: "Fajar A. Nugraha" <fajar@xxxxxxxxx>
  • From: Alba <florfoto@xxxxxxxxx>
  • Date: Wed, 20 May 2009 18:05:12 -0300
  • Cc: xen-users@xxxxxxxxxxxxxxxxxxx
  • Delivery-date: Wed, 20 May 2009 14:11:31 -0700
  • Domainkey-signature: a=rsa-sha1; c=nofws; d=gmail.com; s=gamma; h=mime-version:in-reply-to:references:date:message-id:subject:from:to :cc:content-type; b=xEkCdIwvr78BBKBaUzm4QWCDB2cYJ0NBi2yhvwlQaeS+ez7/T7atoIcc80M2cYvWID Zh9L5gqyxNFu7UBb4z+IvZbxx2kds6OCuqc9zqaS1Qc32gbJ5Ph8k2wDIq5f4xbrid9p UN1CNqNNaop6StAvELgtwn8+iHmwUqFI59pCo=
  • List-id: Xen user discussion <xen-users.lists.xensource.com>

Thanks a lot again for your reply.

> tap:aio should be for file-backed images, not devices. You should have
> disk = [ "tap:aio:/PathToMyImage.img,hda,w", "phy:/dev/sda1,xvdb,w" ]

I followed this procedure, where says that tap:aio should be used (isn't it rigth?):
http://www.redhat.com/docs/en-US/Red_Hat_Enterprise_Linux/5.2/html/Para-Virtualized_Windows_Drivers/sect-Para-Virtualized_Windows_Drivers-Installing_and_configuring_the_para_virtualized_drivers-Post_installation_host_configuration.html

>How many disks you have each? Do you have one or two QEMU disks?
>QEMU harddisk should be hda, while RHEL disk should be xvdb.

With this configuration I saw three devices:
disk = [ "file:PathToMyImage.img,hda,w", "tap:aio:/dev/sda1,xvdb,w" ]

The devices are:

1) "c:" (10GB)
2) "QEMU HARDDISK" (50GB)
3) "RHEL DISK SCSI Disk Device" (50GB)
   
The only difference between 2) and 3) are in their Properties:
2) says "Location: Location 1 (1)"   
3) says "Location: Bus Number 0, Target Id 0, LUN 1"

So I'm not sure if I should put my data in 2) or 3).

Thanks for your time.

Regards.

On Tue, May 19, 2009 at 10:36 PM, Fajar A. Nugraha <fajar@xxxxxxxxx> wrote:
On Wed, May 20, 2009 at 4:16 AM, Alba <florfoto@xxxxxxxxx> wrote:
> Thanks Fajar for your reply.
> I'm not using Redhat PV drivers on boot disk.

but you ARE using Redhat's PV driver?

>
> My DomU config file is:
>
> disk = [ "file:PathToMyImage.img,hda,w", "tap:aio:/dev/sda1,xvdb,w" ]
>

tap:aio should be for file-backed images, not devices. You should have

disk = [ "tap:aio:/PathToMyImage.img,hda,w", "phy:/dev/sda1,xvdb,w" ]


> I'm not sure which disk should I use in the Win DomU: if the one that says
> "QEMU HARDDISK"  or the one that says "RHEL DISK SCSI Disk Device".

How many disks you have each? Do you have one or two QEMU disks?
QEMU harddisk should be hda, while RHEL disk should be xvdb.

--
Fajar

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users

 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.