RE: [Xen-users] which port do i use to connect to my XCP 0.5 server?

["Joe Linoff" <jlinoff@xxxxxxxxxx>]

Hi Vern:

Thank you. I just tried that:

  % xe -s <IP address> -u root -pw <password>
  Error: Connection reset by peer (calling read )

I used the same password that I used to log into the XCP server.

BTW, I was just starting to play with XCCS. It looks very interesting.

Cheers,

Joe

-----Original Message-----
From: Vern Burke [mailto:vburke@xxxxxxxx] 
Sent: Wednesday, November 24, 2010 3:24 PM
To: Joe Linoff; xen-users-bounces@xxxxxxxxxxxxxxxxxxx
Cc: xen-users@xxxxxxxxxxxxxxxxxxx
Subject: Re: [Xen-users] which port do i use to connect to my XCP 0.5
server?

You didn't specify the user name (-u). You need 3 things to use xe
remotely, user name (-u), password (-pw), and server address (-s).

Vern
Vern Burke, SwiftWater Telecom, http://www.swiftwatertel.com

-----Original Message-----
From: "Joe Linoff" <jlinoff@xxxxxxxxxx>
Sender: xen-users-bounces@xxxxxxxxxxxxxxxxxxx
Date: Wed, 24 Nov 2010 14:58:14 
To: Vern Burke<vburke@xxxxxxxx>
Cc: <xen-users@xxxxxxxxxxxxxxxxxxx>; Joe Linoff<jlinoff@xxxxxxxxxx>
Subject: RE: [Xen-users] which port do i use to connect to my XCP 0.5
server?

Hi Vern:

Thank you for your quick reply. I apologize for not being clear in my
problem statement.

I am able to successfully run xe from the XCP server (no port) but I am
unable to run it from the master on the network. The master is not an
XCP. It is a CentOS 5.5 workstation.

I installed xe on the master and tried to run this:

  % xe help
  Failed to contact a running XenServer management agent.
  Try specifying a server name and port.
  <snipped>

I then tried that but was stumped at the port. After hunting through
previous emails I found a reference to port 443 but then I assumed that
since it was a default, xe would figure out so I tried this:

  % xe help -s <IP-address> -pw <password>
  Error: Connection reset by peer (calling read )

At that point I was stumped. I thought that the problem was occurring
because of a bad port. It appears that is not the case. Do you have any
idea what the problem might be?

Cheers,

Joe

-----Original Message-----
From: Vern Burke [mailto:vburke@xxxxxxxx] 
Sent: Wednesday, November 24, 2010 2:46 PM
To: Joe Linoff
Cc: xen-users@xxxxxxxxxxxxxxxxxxx
Subject: Re: [Xen-users] which port do i use to connect to my XCP 0.5
server?

If you're using xe from the XCP host's command line, you don't need a 
port. If you're using xe from a different machine, don't specify the 
port unless you have to change it for some off reason, default works
fine.

Vern Burke

SwiftWater Telecom
http://www.swiftwatertel.com
Xen Cloud Control System
http://xencloudcontrol.com

On 11/24/2010 5:35 PM, Joe Linoff wrote:
> Hi Folks:
>
> I downloaded and installed XCP 0.5 on a server machine on my network.
I
> would now like to communicate with it using xe but I am told that I
need
> a port number. What port number should I use?
>
> I tried looking this up on the xen.org web site:
> http://wiki.xen.org/xenwiki/Command_Line_Interface. It said to look at
> chapter 8 in the Administrators guide but that guide is unavailable:
> http://www.xen.org/products/cloud_support.html. The message says that
it
> is under construction. Where else can I look?
>
> Thanks,
>
> Joe
>
>
>
>_______________________________________________
> Xen-users mailing list
> Xen-users@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-users

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users