Re: [Xen-users] Xen 3.3 NetBSD DOM0: xenconsole: Could not read tty from store: No such file or directory

[Roger Pau Monnà <roger.pau@xxxxxxxxxxxxx>]

> Thanks, Roger. ÂI got sidetracked with other problems for a day or so. ÂThat
> indeed does work fine.
> Now I've got bridging problems, though.
>
> On my DOM0:
>
> voodoo# cat /etc/ifconfig.bridge0
> Âcreate
> !brconfig $int add bge0 up
>
> voodoo# ifconfig -a
> Âbge0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
>
> capabilities=3f80<TSO4,IP4CSUM_Rx,IP4CSUM_Tx,TCP4CSUM_Rx,TCP4CSUM_Tx,UDP4CSUM_Rx,UDP4CSUM_Tx>
> Â Â Â enabled=0
> Â Â Â address: bc:30:5b:d0:a1:46
> Â Â Â media: Ethernet autoselect (1000baseT
> full-duplex,flowcontrol,rxpause,txpause)
> Â Â Â status: active
> Â Â Â inet 172.17.9.38 netmask 0xffffff00 broadcast 172.17.9.255
> Â Â Â inet6 fe80::be30:5bff:fed0:a146%bge0 prefixlen 64 scopeid 0x1
> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33648
> Â Â Â inet 127.0.0.1 netmask 0xff000000
> Â Â Â inet6 ::1 prefixlen 128
> Â Â Â inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
> bridge0: flags=41<UP,RUNNING> mtu 1500
>
> voodoo# cat /usr/pkg/etc/xen/juju                   kernel
> = '/usr/pkg/lib/xen/boot/hvmloader'
> builder = 'hvm'
> memory = 4096
> vcpus = 4
> name = 'juju'
> vif = [ 'mac=00:16:3e:00:00:01, bridge=bridge0, type=ioemu' ]

Have you tried with:

vif = [ 'mac=00:16:3e:00:00:01, bridge=bridge0' ]

> device_model = '/usr/pkg/libexec/qemu-dm'
> disk = [ 'file:/Xen/Disks/juju0000.img,ioemu:hda,w' ]
> boot = 'c'
> vnc = 1
> vnclisten = '0.0.0.0'
> vncpasswd = 'XXXXXX'
> vncdisplay = 1
>
> voodoo# xm create /usr/pkg/etc/xen/juju
> Using config file "/usr/pkg/etc/xen/juju".
> Started domain juju
>
> voodoo# xm list
> Name                    ÂID  Mem VCPUs   ÂState
> Time(s)
> Domain-0 Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â 0 Â1024 Â Â 1 Â Â r-----
> 11.0
> juju                     1 Â4096   4   -b----
> 46.0
>
> voodoo# ifconfig -a
> Âbge0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
>
> capabilities=3f80<TSO4,IP4CSUM_Rx,IP4CSUM_Tx,TCP4CSUM_Rx,TCP4CSUM_Tx,UDP4CSUM_Rx,UDP4CSUM_Tx>
> Â Â Â enabled=0
> Â Â Â address: bc:30:5b:d0:a1:46
> Â Â Â media: Ethernet autoselect (1000baseT
> full-duplex,flowcontrol,rxpause,txpause)
> Â Â Â status: active
> Â Â Â inet 172.17.9.38 netmask 0xffffff00 broadcast 172.17.9.255
> Â Â Â inet6 fe80::be30:5bff:fed0:a146%bge0 prefixlen 64 scopeid 0x1
> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33648
> Â Â Â inet 127.0.0.1 netmask 0xff000000
> Â Â Â inet6 ::1 prefixlen 128
> Â Â Â inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
> bridge0: flags=41<UP,RUNNING> mtu 1500
> xvif1.0: flags=8923<UP,BROADCAST,NOTRAILERS,PROMISC,SIMPLEX,MULTICAST> mtu
> 1500
> Â Â Â capabilities=2800<TCP4CSUM_Tx,UDP4CSUM_Tx>
> Â Â Â enabled=0
> Â Â Â address: 00:16:3e:01:00:01
> Â Â Â inet6 fe80::216:3eff:fe01:1%xvif1.0 prefixlen 64 scopeid 0x4
> tap0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
> Â Â Â address: f2:0b:a4:80:47:02
> Â Â Â media: Ethernet autoselect
> Â Â Â inet6 fe80::f00b:a4ff:fe80:4702%tap0 prefixlen 64 scopeid 0x5


Can you post the output of "brconfig bridge0"? (only the Interfaces
section is fine). Also you could perform a tcpdump of interface bge0,
to see if packets can reach it.

> The re0 device on the FreeBSD DOMU is set up on 172.17.9.33, everything
> looks fine there [I can do screenshots if needed] but there's no
> connectivity, DOM0->DOMU or DOMU->DOM0. ÂHere again, I'm pretty sure it's
> some little detail I'm missing and just not seeing.
>
> Thanks in advance.
>
> --
> Ron McDowell
> San Antonio TX
>
>
>
> _______________________________________________
> Xen-users mailing list
> Xen-users@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-users
>

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users