Re: [Xen-users] DomUs hidden behind Dom0 in the network?

["Schröter, Philipp" <Philipp.Schroeter@xxxxxxxxxx>]

Hello again,

thanks very much for all the answers.
I have been very busy thus the lack of a prompt answer. Sorry for that.

>...are you able to do NAT?
>
>If so just use your Dom0 as the "NAT router" for your DomUs.
>
>If you have more then one MAC available / known you might configure your DomUs
>with these MACs for their virtual ifaces.
>
>
>hth
>best regards,
>
>
>Niels.
>--
> ---
> Niels Dettenbach
> Syndicat IT & Internet
> http://www.syndicat.com
> PGP: https://syndicat.com/pub_key.asc
> ---

Yeah, I think NAT is the way to go regarding my issues.
The problem is that I only have one IP address, it's linked to the MAC address 
of the server and I won't get additional IP addresses.

>In xend-config.sxp:
>
>(network-script network-nat)
>(vif-script     vif-nat)
>
>
>(instead of i.e. bridging or normal routing scripts - never tried xens NAT
>scrip's but i assume they do that what they are called ;).
>
>
>
>Or do it similiar by hand with:
>
>echo 1 > /proc/sys/net/ipv4/ip_forward
>
>iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
>iptables -A FORWARD -i eth0 -o eth1 -m state --state RELATED,ESTABLISHED -j
>ACCEPT
>iptables -A FORWARD -i eth1 -o eth0 -j ACCEPT
>
>
>where eth0 is the "outgoing" network interface to LAN of the Dom0.
>
>
>
>cheers,
>
>Niels.
>--
> ---
> Niels Dettenbach
> Syndicat IT & Internet
> http://www.syndicat.com
> PGP: https://syndicat.com/pub_key.asc

I tried that and it didn't work for me. Just changing the Xen script from 
bridge to NAT didn't help.
I have two network interface controllers, eth0 and eth1. eth0 is the one that 
communicates with the network and has (limited, only http) access to the 
internet. That's why I thought about using eth1 to connect the domU's and dom0.

For the domU cfg file I followed this guide
https://help.ubuntu.com/community/Xen

receiving the following cfg file
name = "ubuntu-net"
memory = 256
disk = ['phy:/dev/xenvg/ubuntu-net,xvda,w']
vif = ['ip=192.168.3.2']
kernel = "/var/lib/xen/images/ubuntu-netboot/vmlinuz"
ramdisk = "/var/lib/xen/images/ubuntu-netboot/initrd.gz"
extra = "debian-installer/exit/always_halt=true -- console=hvc0"

which starts but doesn't gain net access and thus can't not be installed 
correct.

I configured /etc/network/interfaces in this way:
auto eth0
iface eth0 inet dhcp

auto eth1
iface eth1 inet static
        address 192.168.3.1
        network 192.168.3.0
        netmask 255.255.255.0
        broadcast 192.168.3.255

up /sbin/iptables -A FORWARD -o eth0 -i eth1 -s 192.168.3.0/16 -m conntrack 
--ctstate NEW -j ACCEPT
up /sbin/iptables -A FORWARD -o eth0 -s 192.168.0.0/16 -m conntrack --ctstate 
NEW -j ACCEPT
up /sbin/iptables -A FORWARD -m conntrack --ctstate ESTABLISHED,RELATED -j 
ACCEPT
up /sbin/iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
up /etc/init.d/dnsmasq restart

route tells me this:
Destination     Gateway            Genmask         Flags Metric Ref    Use Iface
default         vrrp-sonst0010.    0.0.0.0           UG    100    0        0 
eth0
141.42.152.0    *                     255.255.254.0   U     0      0        0 
eth0
192.168.3.0     *                     255.255.255.0   U     0      0        0 
eth1

and ifconfig this:
eth0      Link encap:Ethernet  HWaddr 00:30:48:bd:61:14
             inet addr:141.42.152.159  Bcast:141.42.153.255  Mask:255.255.254.0
            inet6 addr: fe80::230:48ff:febd:6114/64 Scope:Link

eth1      Link encap:Ethernet  HWaddr 00:30:48:bd:61:15
            inet addr:192.168.3.1  Bcast:192.168.3.255  Mask:255.255.255.0
            UP BROADCAST MULTICAST  MTU:1500  Metric:1


Best regards,
Philipp
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxx
http://lists.xen.org/xen-users