Xen project Mailing List

I changed the /chosen node in the dts file to

#######################################
    chosen {
        stdout-path = "serial0:115200n8";
        xen,xen-bootargs = "dom0_mem=752M console=dtuart dtuart=serial0 dom0_max_vcpus=4";
        xen,dom0-bootargs = "console=ttyS0,115200 rw root=/dev/mmcblk0p2 ignore_loglevel cma=128M";
        modules {
            #address-cells = <2>;
            #size-cells = <2>;
            module@1 {
                compatible = "xen,linux-zimage", "xen,multiboot-module";
                reg = <0x0 0x7a000000 0x0 0x02000000>;
            };
        };
    };
#######################################

Also, the xen-related features in the kernel are as follows (created by default after selecting "Kernel features => Xen guest support on ARM" in menuconfig) :

#######################################
CONFIG_XEN_DOM0=y
CONFIG_XEN=y
CONFIG_XEN_BLKDEV_FRONTEND=y
CONFIG_XEN_NETDEV_FRONTEND=y
CONFIG_INPUT_XEN_KBDDEV_FRONTEND=y
CONFIG_HVC_XEN=y
CONFIG_HVC_XEN_FRONTEND=y
CONFIG_XEN_FBDEV_FRONTEND=y
CONFIG_XEN_BALLOON=y
CONFIG_XEN_SCRUB_PAGES=y
CONFIG_XEN_DEV_EVTCHN=y
CONFIG_XEN_BACKEND=y
CONFIG_XENFS=y
CONFIG_XEN_COMPAT_XENFS=y
CONFIG_XEN_SYS_HYPERVISOR=y
CONFIG_XEN_XENBUS_FRONTEND=y
CONFIG_XEN_GNTDEV=m
CONFIG_XEN_GRANT_DEV_ALLOC=m
CONFIG_SWIOTLB_XEN=y
CONFIG_XEN_PRIVCMD=y
CONFIG_XEN_AUTO_XLATE=y

# CONFIG_XEN_BLKDEV_BACKEND is not set
# CONFIG_XEN_SCSI_FRONTEND is not set
# CONFIG_XEN_NETDEV_BACKEND is not set
# CONFIG_XEN_WDT is not set
# CONFIG_XEN_PVCALLS_FRONTEND is not set
# CONFIG_XEN_PVCALLS_BACKEND is not set
#######################################

However, I see absolutely no change in the observations; no xen-related log on the serial-console, and "sudo xl list" gives the same error messages.

What am I lacking?

On Sat, Apr 28, 2018 at 11:06 PM, Andrew Cooper <andrew.cooper3@xxxxxxxxxx> wrote:

On 28/04/18 18:34, Ajay Garg wrote:

Hi Andrew.

Thanks for the reply.

On Sat, Apr 28, 2018 at 10:57 PM, Andrew Cooper <andrew.cooper3@xxxxxxxxxx> wrote:

On 28/04/18 18:12, Ajay Garg wrote:

Hi All.

We have brought up the cubieboard2 from almost scratch, following are the steps done :

<snip>

== getting xen ready ==

i)

Compiled xen on cubieboard itself, via :

   * git clone git://xenbits.xen.org/xen.git
   * cd xen
. * ./configure --libdir=/usr/lib
   * make debball CONFIG_EARLY_PRINTK=sun7i -j4

   * sudo dpkg -i dist/xen-upstream-4.11-unstable.deb

   * sudo reboot

ii)

Upon reboot, "sudo xl list" gives following :

##################################################################
debian@debian-armhf:~$ sudo xl list
[sudo] password for debian:
xencall: error: Could not obtain handle on privileged command interface: No such file or directory
libxl: error: libxl.c:102:libxl_ctx_alloc: cannot open libxc handle: No such file or directory
cannot init xl context
##################################################################

This means that /dev/xen/privcmd (or the legacy /proc/xen/privcmd) device isn't available.

First check that you have actually booted Xen with Linux as dom0. You don't show any logs in this final section, and simply installing the debball and rebooting won't typically cause Xen to be the head of the boot list.

Yes, I haven't been able to setup xen bootup.

That's why, requested help regarding the changes that are required in https://github.com/torvalds/linux/blob/master/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts, that would cause dom0 to boot up.

Sorry for the confusion.

Ah - sorry. I misunderstood. I'm afraid you're going to have to wait for some people more knowledge about ARM to answer.

~Andrew

Regards,
Ajay

Re: [Xen-users] [Xen-devel] [cubieboard2] Bringing up dom0