Re: Query regarding builnig Xen on Raspberry-Pi3

[Bertrand Marquis <Bertrand.Marquis@xxxxxxx>]

> On 14 May 2020, at 10:44, Bertrand Marquis <bertrand.marquis@xxxxxxx> wrote:
> 
> 
> 
>> On 14 May 2020, at 10:43, siddhartha v <siddhuvgowda.18695@xxxxxxxxx> wrote:
>> 
>> ok sir,
>> 
>> For building should I use "bitbake xen-image-minimal" command?
> 
> Please use:
> bitbake xen-image-minimal.bb

Sorry remove .bb

Bertrand

> 
>> 
>> On Thu, May 14, 2020 at 2:58 PM Bertrand Marquis <Bertrand.Marquis@xxxxxxx> 
>> wrote:
>> Hi,
>> 
>>> On 14 May 2020, at 10:24, siddhartha v <siddhuvgowda.18695@xxxxxxxxx> wrote:
>>> 
>>> Hi sir, 
>>>  I tried to build by adding the line that you suggested but I got below 
>>> error:
>>> 
>>> siddhu@siddhu:~/Documents/yocto/build$ bitbake core-image-base
>>> ERROR: Unable to start bitbake server (None)
>>> ERROR: Server log for this session 
>>> (/home/siddhu/Documents/yocto/build/bitbake-cookerdaemon.log):
>>> --- Starting bitbake server pid 26317 at 2020-05-14 14:52:35.773040 ---
>>> ERROR: ParseError at /home/siddhu/Documents/yocto/build/conf/local.conf:43: 
>>> unparsed line: 'DISTRO_FEATURES += “virtualization xen”'
>>> siddhu@siddhu:~/Documents/yocto/build$ 
>>> 
>> 
>> You must have some wrong comas in the line.
>> Please try to rewrite it.
>> 
>> Bertrand
>> 
>>> 
>>> 
>>> On Thu, May 14, 2020 at 1:17 PM Bertrand Marquis <Bertrand.Marquis@xxxxxxx> 
>>> wrote:
>>> 
>>>> On 14 May 2020, at 08:16, siddhartha v <siddhuvgowda.18695@xxxxxxxxx> 
>>>> wrote:
>>>> 
>>>> Hello,
>>>> 
>>>>       I am trying to build the Xen to my Raspberry pi3 board. Below is the 
>>>> details,
>>>> BBlayers.conf file:
>>>> 
>>>> # POKY_BBLAYERS_CONF_VERSION is increased each time 
>>>> build/conf/bblayers.conf
>>>> # changes incompatibly
>>>> POKY_BBLAYERS_CONF_VERSION = "2"
>>>> 
>>>> BBPATH = "${TOPDIR}"
>>>> BBFILES ?= ""
>>>> 
>>>> BBLAYERS ?= " \
>>>>  /home/siddhu/Documents/yocto/sources/poky/meta \
>>>>  /home/siddhu/Documents/yocto/sources/poky/meta-poky \
>>>>  /home/siddhu/Documents/yocto/sources/poky/meta-yocto-bsp \
>>>>  /home/siddhu/Documents/yocto/sources/meta-openembedded/meta-oe \
>>>>  /home/siddhu/Documents/yocto/sources/meta-openembedded/meta-multimedia \
>>>>  /home/siddhu/Documents/yocto/sources/meta-openembedded/meta-python \
>>>>  /home/siddhu/Documents/yocto/sources/meta-openembedded/meta-networking \
>>>>  /home/siddhu/Documents/yocto/sources/meta-openembedded/meta-filesystems \
>>>>  /home/siddhu/Documents/yocto/sources/meta-cloud-services \
>>>>  /home/siddhu/Documents/yocto/sources/meta-selinux \
>>>>  /home/siddhu/Documents/yocto/sources/meta-virtualization\
>>>>  /home/siddhu/Documents/yocto/sources/meta-raspberrypi \
>>>>  "
>>>> 
>>>> The build went well but after writing to SD card. I typed "$: xl info " 
>>>> but I got " xl not found" error. May I know what mistake I am doing here 
>>>> please.
>>>> 
>>>> 
>>>> I have attached the local.conf too where I have enabled the virtualisation 
>>>> after going through the readme of the meta-virtualisation.
>>> 
>>> To activate Xen build you need to add to your local.conf:
>>> 
>>> DISTRO_FEATURES += “virtualization xen”
>>> 
>>> You have something to add virtualization but not xen
>>> 
>>> Then you must start Xen which should start Linux, in your current system 
>>> you have more then probably just started the Linux generated but Xen needs 
>>> to be started first and then Xen is starting Linux.
>>> 
>>> Once you have done that, it would also help if you provide your boot logs.
>>> 
>>> Regards
>>> Bertrand
>>> 
>>>> -- 
>>>> Thanks and Regards.
>>>> Siddhartha V.
>>>> 
>>>> <local.conf>
>>> 
>>> 
>>> 
>>> -- 
>>> Thanks and Regards.
>>> Siddhartha V.
>>> 
>> 
>> 
>> 
>> -- 
>> Thanks and Regards.
>> Siddhartha V.
>> 
>