[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: [Xen-devel] expose MWAIT to dom0



>>> On 16.08.11 at 10:29, "Tian, Kevin" <kevin.tian@xxxxxxxxx> wrote:
>>  From: Jan Beulich [mailto:JBeulich@xxxxxxxxxx] 
>> Sent: Tuesday, August 16, 2011 4:13 PM
>> 
>> >>> On 16.08.11 at 08:53, "Tian, Kevin" <kevin.tian@xxxxxxxxx> wrote:
>> >>  From: Jan Beulich [mailto:JBeulich@xxxxxxxxxx] 
>> >> Sent: Tuesday, August 16, 2011 2:42 PM
>> >>
>> >> >>> On 16.08.11 at 08:03, "Tian, Kevin" <kevin.tian@xxxxxxxxx> wrote:
>> >> >>  From: Jan Beulich [mailto:JBeulich@xxxxxxxxxx] 
>> >> >> Sent: Monday, August 15, 2011 6:29 PM
>> >> >>
>> >> >> that while improving the situation on CPUs that support the break-on-
>> >> >> interrupt extension to mwait, it would result in C2/C3 not being usable
>> >> >> at all on CPUs that don't (but support mwait in its simpler form and
>> >> >> have ACPI tables specifying FFH as address space id). Is that only a
>> >> >> theoretical concern (i.e. is there an implicit guarantee that for other
>> >> >> than C1 FFH wouldn't be specified without that extension being
>> >> >> available)? I thinks it's a practical one, or otherwise there wouldn't
>> >> >> be a point in removing the ACPI_PDC_C_C2C3_FFH bit prior to _PDC
>> >> >> evaluation.
>> >> >
>> >> > Yes, this is a practical one, though I don't know any box doing that. In
>> > all
>> >> > the boxes I've been using so far, all the extensions are available. But
>> >> > since
>> >> > BIOS vendor may also impact the availability of CPUID bits, I think we
>> >> > should do it right by strictly conforming to theSDM. I.e. we need check
>> >> > CPUID leafs and then verify all Cx states propagated from dom0, instead
>> >> > of blindly following its info. Will work a patch for that.
>> >>
>> >> You're getting it sort of wrong way round: What I don't want to do (but
>> >> seemingly being necessary) is mimic the decision logic the hypervisor
>> >> uses (i.e. require the break-on-interrupt extension for C2/C3 entering
>> >> through MWAIT) in Dom0 when deciding about the bits to pass to
>> >
>> > break-on-interrupt is not a hard requirement to use MWAIT. Even when
>> > that extension is not available, MWAIT can be still used to enter C2/C3,
>> > just with interrupt enabled.
>> 
>> And that's why this implementation detail should be confined to the
>> hypervisor - Dom0 should not care about this if at all possible.
>> 
>> >> _PDC. That ought to be an implementation detail (subject to change)
>> >> in the hypervisor alone. The hypervisor itself, otoh, already properly
>> >> checks CPUID leaf 5 (and that's what might cause it to not use mwait
>> >> despite the bit in CPUID leaf 1 being set, which should be all Dom0
>> >> ought to look at for deciding whether to clear ACPI_PDC_C_C2C3_FFH).
>> >>
>> >
>> > I made a mistake, that currently CPUID leaf 5 is already checked in
>> > check_cx in hypervisor, so it should be sane. However I still fail to catch
>> > your real concern here. :/
>> 
>> If Dom0 finds (real) CPUID leaf 1 report MWAIT to be available, it
>> will (with the logic outlined above) call _PDC without clearing
>> ACPI_PDC_C_C2C3_FFH. If now the break-on-interrupt extension
>> is not present, but the address space ID for C2 or C3 is set to FFH,
>> then Xen (in acpi_processor_ffh_cstate_probe()) will reject the
>> Cx entry (and hence refrain from using the respective C-state),
>> whereas if Dom0 cleared ACPI_PDC_C_C2C3_FFH in that case,
>> firmware would (normally) have converted the address space ID to
>> SYSTEM_IO, and hence Xen would have decided to use C2/C3 with
>> the SYSIO entry method.
>> 
>> So this is only acceptable if there are *no* production CPUs of any
>> vendor that would support MWAIT without the break-on-interrupt
>> extension.
>> 
> 
> yes, that's also the way that native Linux code currently uses:
>       - notify BIOS ACPI_PDC_C_C2C3_FFH if cpu has mwait
>       - reject Cx entry if break-on-interrupt extension is not present later
> in acpi processor driver when parsing Cx entries.
> 
> From BIOS ACPI p.o.v, OSPM can notify BIOS about FFH style if following
> conditions are true:
>       a) cpu supports mwait
>       b) OSPM itself supports mwait
> 
> a) is architectural, but b) is implementation specific regarding to what
> can be called "support". Obviously both Xen and Linux here use an
> inconsistent way between the place notifying BIOS and the point parsing
> ACPI Cx entry. So your conclusion is correct that C2/C3 would be rejected
> on the CPU which doesn't support MWAIT with break-on-interrupt 
> extension. But it should be fine in the real world, and we may consider
> whether to do something when a real case is encountered in the future.
> 
> On the other hand, you can think it as the decision from Xen that it
> doesn't want to use legacy I/O method for C2/C3 when such situation exists. 
> :-)

Yeah, but customers could validly view this as regression (because on
such a system Xen would use C2/C3 currently).

Jan

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel


 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.