[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-devel] Xen doesn't boot on grub2 or xend doesn't start



Pasi

I didn't think this. I'll be in my job tomorrow an I'll reply there.

Thank you

Em 23 de abril de 2012 13:23, Pasi Kärkkäinen <pasik@xxxxxx> escreveu:
On Mon, Apr 23, 2012 at 01:13:49PM -0300, José Eduardo França wrote:
>    Hi Pasi,
>
>    thank you for reply.
>
>    I'm using Debian Squeeze, and I'm compiling Xen from source (.tar.gz). I
>    ran "make install-tools PYTHON_PREFIX_ARG=" to install Xen.
>
>    Notice: I couldn't run in xen_unstable or dom0 then I returned to install
>    environment (Debian Squeeze)
>
>    My attempt with modules and now with xenstored command (oxenstored command
>    works) was in Debian Squeeze. In this case I think I can't load these
>    modules or run this command, but I'm not sure. Then your questions can not
>    be in this scope. What do you think?
>

I was talking about dom0 Linux kernel, not about Xen.

-- Pasi


>    Thanks, Eduardo
>
>    Em 23 de abril de 2012 03:36, Pasi Kärkkäinen <[1]pasik@xxxxxx> escreveu:
>
>      On Sun, Apr 22, 2012 at 04:21:10PM -0300, José Eduardo França wrote:
>      >    hi guys,
>      >
>
>      Hello,
>      >    It's my first time here and in a mailing lists, I only participated
>      in
>      >    forums before. Please, If I make a mistake you should advise me.
>      Let's go!
>      >
>      >    I was reading "xencommons not start" in a Remus Forum in order to
>      install
>      >    Remus.
>      >    Well* I followed the tutorial
>      >
>       <[1][2]http://remusha.wikidot.com/configuring-and-installing-remus>, I
>      reboot
>      >    in xen_unstable and I had a error message:
>      >
>      >    error: couldn't open file
>      >    error: you need to load the multiboot kernel first
>      >
>      >    then I redid tutorial after "Adapt Grub" and in a moment I do
>      command:
>      >
>      >    # /etc/init.d/xend start
>      >    xencommons should be started first.
>      >
>      >    but I had done "/etc/init.d/xencommons start" before and no error
>      message
>      >    returned !!!???
>      >
>      >    I also tried insert modules manually (coz in other mailing list
>      said to
>      >    put some modules - see my setups after this mail) but I had:
>      >
>      >    # modprobe xen-evtchn
>      >    FATAL: Module xen_evtchn not found.
>      >
>
>      So xen event channel support is not compiled as a module?
>      is it enabled at all in your dom0 kernel config?
>
>      [3]http://wiki.xen.org/wiki/Xen_Common_Problems#Starting_xend_fails.3F
>      -- Pasi
>
> References
>
>    Visible links
>    1. mailto:pasik@xxxxxx
>    2. http://remusha.wikidot.com/configuring-and-installing-remus
>    3. http://wiki.xen.org/wiki/Xen_Common_Problems#Starting_xend_fails.3F

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
http://lists.xen.org/xen-devel

 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.