[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-devel] [v7][RFC][PATCH 08/13] xen/x86/p2m: set p2m_access_n for reserved device memory mapping



>>> On 27.10.14 at 10:05, <tiejun.chen@xxxxxxxxx> wrote:
> On 2014/10/24 23:11, Jan Beulich wrote:
>>>>> On 24.10.14 at 09:34, <tiejun.chen@xxxxxxxxx> wrote:
>   int
>   guest_physmap_add_entry(struct domain *d, unsigned long gfn,
>                           unsigned long mfn, unsigned int page_order,
> 
>>
>>> +            if ( rc )
>>
>> And the return value from the called function is of type int -
>> non-zero may not just mean "true" but (when negative) also
>> "error". You need to distinguish these cases.
> 
> But in our case its impossible to get a negative value.

Being guaranteed by what? Please don't simply take the
_current implementation_ of iommu_get_reserved_device_memory()
as reference - it could be changed at any time, and it allowing for an
error return status already would make it perfectly fine for someone
adding an actual case thereof not to go through all existing callers
to check whether they can cope. This is a general code quality
requirement to assure things remain maintainable.

>>> +            {
>>> +                /*
>>> +                 * Just set p2m_access_n in case of shared-ept
>>> +                 * or non-shared ept but 1:1 mapping.
>>> +                 */
>>> +                if ( iommu_use_hap_pt(d) ||
>>> +                     (!iommu_use_hap_pt(d) && mfn == gfn) )
>>
>> How would, other than by chance, mfn equal gfn here? Also the
>> double use of iommu_use_hap_pt(d) is pointless here.
> 
> There are two scenarios we should concern:
> 
> #1 in case of shared-ept.
> 
> We always need to check so iommu_use_hap_pt(d) is good.
> 
> #2 in case of non-sharepd-ept
> 
> If mfn != gfn I think guest don't access RMRR range, so its allowed.

And what if subsequently a device needing a 1:1 mapping at this GFN
gets assigned? (I simply don't see why shared vs non-shared would
matter here.)

>>> +                {
>>> +                    rc = p2m_set_entry(p2m, gfn, _mfn(mfn), page_order, t,
>>> +                                       p2m_access_n);
>>> +                    if ( rc )
>>> +                        gdprintk(XENLOG_WARNING, "set rdm p2m failed: 
>>> (%#lx)\n",
>>> +                                 gfn);
>>
>> Such messages are (due to acting on a foreign domain) relatively
>> useless without also logging the domain that is affected. Conversely,
>> logging the current domain and vCPU (due to using gdprintk()) is
>> rather pointless. Also please drop either the colon or the
>> parentheses in the message.
> 
> Can P2M_DEBUG work here?
> 
> P2M_DEBUG("set rdm p2m failed: %#lx\n", gfn);

I don't think this would magically add the missing information. Plus it
would limit output to the !NDEBUG case, putting the practical
usefulness of this under question even more.

But anyway, looking at the existing code again, I think you'd be better
off falling through to the p2m_set_entry() that's already there, just
altering the access permission value you pass. Less code, better
readable.

Jan


_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
http://lists.xen.org/xen-devel


 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.