|
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] [Xen-devel] dom0 kernel didnot boot while transplanting the xen-4.7 on OMAP5432 uEVM board
hi ! I am transplanting the xen-4.7 on my OMAP5432 uEVM board,but after booting the xen ,the dom0 kernel didnot boot successfully(no console output while booting the dom0 kernel).I followed my step from this link: Xen_ARM_with_Virtualization_Extensions/OMAP5432_uEVM my u-boot command and boot log are as follow: Is there any mistake i have made? could you give me some advice? my U-boot command : ------------------------------------------------------------------------------------------------------------------------------- setenv dtb_addr_r 0x825f0000 setenv xen_addr_r 0x90000000 setenv kernel_addr_r 0xa0000000 setenv xen_bootargs 'sync_console console=dtuart dtuart=serial2' setenv dom0_bootargs 'console=hvc0,115200n8 earlyprintk=xen debug ignore_loglevel root=/dev/mmcblk0p2 rw rootwait fixrtc' fatload mmc 0:1 $dtb_addr_r omap5-uevm.dtb fatload mmc 0:1 $xen_addr_r xen-uImage fatload mmc 0:1 $kernel_addr_r zImage fdt addr $dtb_addr_r fdt resize fdt set /chosen xen,xen-bootargs \"$xen_bootargs\" fdt resize fdt set /chosen xen,dom0-bootargs \"$dom0_bootargs\" fdt mknode /chosen modules fdt set /chosen/modules '#address-cells' <1> fdt set /chosen/modules '#size-cells' <1> fdt mknode /chosen/modules module@0 fdt set /chosen/modules/module@0 compatible xen,linux-zimage xen,multiboot-module fdt set /chosen/modules/module@0 reg <$kernel_addr_r 0xa00000> bootm $xen_addr_r - $dtb_addr_r ------------------------------------------------------------------------------------------------------------------------------- my boot log : ------------------------------------------------------------------------------------------------------------- ## Booting kernel from Legacy Image at 90000000 ... Image Name: Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 787308 Bytes = 768.9 KiB Load Address: 80200000 Entry Point: 80200000 Verifying Checksum ... OK ## Flattened Device Tree blob at 825f0000 Booting using the fdt blob at 0x825f0000 Loading Kernel Image ... OK OK reserving fdt memory region: addr=825f0000 size=d000 Loading Device Tree to beeef000, end beefefff ... OK Starting kernel ... - UART enabled - - CPU 00000000 booting - - Xen starting in Hyp mode - - Zero BSS - - Setting up control registers - - Turning on paging - - Ready - (XEN) Checking for initrd in /chosen (XEN) RAM: 0000000080000000 - 00000000beffffff (XEN) (XEN) MODULE[0]: 00000000beeef000 - 00000000beeff000 Device Tree (XEN) MODULE[1]: 00000000a0000000 - 00000000a0a00000 Kernel (XEN) RESVD[0]: 00000000825f0000 - 00000000825fd000 (XEN) (XEN) Command line: sync_console console=dtuart dtuart=serial2 (XEN) Placing Xen at 0x00000000bec00000-0x00000000bee00000 (XEN) Update BOOTMOD_XEN from 0000000080200000-0000000080309701 => 00000000bec00000-00000000bed09701 (XEN) Xen heap: 00000000bc000000-00000000be000000 (8192 pages) (XEN) Dom heap: 249856 pages (XEN) Domain heap initialised (XEN) Platform: TI OMAP5 (XEN) Looking for dtuart at "serial2", options "" (XEN) omap-uart: Unable to retrieve the IRQ (XEN) Unable to initialize dtuart: -22 (XEN) Bad console= option 'dtuart' Xen 4.7-unstable (XEN) Xen version 4.7-unstable (root@) (arm-linux-gnueabihf-gcc (Linaro GCC 5.1-2015.08) 5.1.1 20150608) debug=y Tue Jan 26 18:21:04 CST 2016 (XEN) Latest ChangeSet: Tue Jan 19 17:47:19 2016 +0000 git:1949868 (XEN) Console output is synchronous. (XEN) Processor: 412fc0f2: "ARM Limited", variant: 0x2, part 0xc0f, rev 0x2 (XEN) 32-bit Execution: (XEN) Processor Features: 00001131:00011011 (XEN) Instruction Sets: AArch32 A32 Thumb Thumb-2 ThumbEE Jazelle (XEN) Extensions: GenericTimer Security (XEN) Debug Features: 02010555 (XEN) Auxiliary Features: 00000000 (XEN) Memory Model Features: 10201105 20000000 01240000 02102211 (XEN) ISA Features: 02101110 13112111 21232041 11112131 10011142 00000000 (XEN) Set AuxCoreBoot1 to 00000000bec0004c (0020004c) (XEN) Set AuxCoreBoot0 to 0x20 (XEN) Generic Timer IRQ: phys=30 hyp=26 virt=27 Freq: 6144 KHz (XEN) GICv2: WARNING: The GICC size is too small: 0x1000 expected 0x2000 (XEN) GICv2 initialization: (XEN) gic_dist_addr=0000000048211000 (XEN) gic_cpu_addr=0000000048212000 (XEN) gic_hyp_addr=0000000048214000 (XEN) gic_vcpu_addr=0000000048216000 (XEN) gic_maintenance_irq=25 (XEN) GICv2: 192 lines, 2 cpus, secure (IID 0000043b). (XEN) Using scheduler: SMP Credit Scheduler (credit) (XEN) Allocated console ring of 16 KiB. (XEN) VFP implementer 0x41 architecture 4 part 0x30 variant 0xf rev 0x0 (XEN) Bringing up CPU1 - CPU 00000001 booting - - Xen starting in Hyp mode - - Setting up control registers - - Turning on paging - - Ready - (XEN) CPU 1 booted. (XEN) Brought up 2 CPUs (XEN) P2M: 40-bit IPA (XEN) P2M: 3 levels with order-1 root, VTCR 0x80003558 (XEN) I/O virtualisation disabled (XEN) *** LOADING DOMAIN 0 *** (XEN) Loading kernel from boot module @ 00000000a0000000 (XEN) Allocating 1:1 mappings totalling 128MB for dom0: (XEN) BANK[0] 0x000000a8000000-0x000000b0000000 (128MB) (XEN) Grant table range: 0x000000bec00000-0x000000bec62000 (XEN) Loading zImage from 00000000a0000000 to 00000000afc00000-00000000aff6cf48 (XEN) Allocating PPI 16 for event channel interrupt (XEN) Loading dom0 DTB to 0x00000000afa00000-0x00000000afa0ce28 (XEN) Scrubbing Free RAM on 1 nodes using 2 CPUs (XEN) ....done. (XEN) Initial low memory virq threshold set at 0x4000 pages. (XEN) Std. Loglevel: All (XEN) Guest Loglevel: All (XEN) ********************************************** (XEN) ******* WARNING: CONSOLE OUTPUT IS SYNCHRONOUS (XEN) ******* This option is intended to aid debugging of Xen by ensuring (XEN) ******* that all output is synchronously delivered on the serial line. (XEN) ******* However it can introduce SIGNIFICANT latencies and affect (XEN) ******* timekeeping. It is NOT recommended for production use! (XEN) ********************************************** (XEN) 3... 2... 1... (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen) (XEN) Freed 284kB init memory. ------------------------------------------------------------------------------------------------------------------------ [no any output after here] Thank you very much! _______________________________________________ Xen-devel mailing list Xen-devel@xxxxxxxxxxxxx http://lists.xen.org/xen-devel
|
 |
Lists.xenproject.org is hosted with RackSpace, monitoring our |