[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-devel] help



i solve the problem by degugging the linux kernel .. the problem was the instruction omap_smc1 ..i'm not sure about what it did but when i delete this instruction it works ... but i face another problem .. the execution now stops in 
 ***********************************************************************************************************************************************************
U-Boot SPL 2013.10-rc2 (Mar 08 2016 - 14:23:51)
OMAP5432 ES2.0
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!
reading u-boot.img
reading u-boot.img


U-Boot 2013.10-rc2 (Mar 08 2016 - 14:23:51)

CPU  : OMAP5432 ES2.0
Board: OMAP5432 uEVM
I2C:   ready
DRAM:  2 GiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
Net:   No ethernet found.
Hit any key to stop autoboot:  0
mmc0 is current device
reading boot.scr
972 bytes read in 5 ms (189.5 KiB/s)
Running bootscript from mmc0 ...
## Executing script at 82000000
reading omap5-uevm.dtb
44836 bytes read in 8 ms (5.3 MiB/s)
reading xen-uImage
787372 bytes read in 44 ms (17.1 MiB/s)
reading zImage
4283720 bytes read in 215 ms (19 MiB/s)
## Booting kernel from Legacy Image at 90000000 ...
   Image Name:
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    787308 Bytes = 768.9 KiB
   Load Address: 80200000
   Entry Point:  80200000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 825f0000
   Booting using the fdt blob at 0x825f0000
   Loading Kernel Image ... OK
   reserving fdt memory region: addr=825f0000 size=c000
   Using Device Tree in place at 825f0000, end 825fefff

Starting kernel ...

- UART enabled -
- CPU 00000000 booting -
- Xen starting in Hyp mode -
- Zero BSS -
- Setting up control registers -
- Turning on paging -
- Ready -
(XEN) Checking for initrd in /chosen
(XEN) RAM: 0000000080000000 - 00000000feffffff
(XEN)
(XEN) MODULE[0]: 00000000825f0000 - 00000000825fc000 Device Tree
(XEN) MODULE[1]: 00000000a0000000 - 00000000a0a00000 Kernel
(XEN)  RESVD[0]: 00000000825f0000 - 00000000825fc000
(XEN)
(XEN) Command line: sync_console console=dtuart dtuart=serial2
(XEN) Placing Xen at 0x00000000fee00000-0x00000000ff000000
(XEN) Update BOOTMOD_XEN from 0000000080200000-0000000080305701 => 00000000fee00000-00000000fef05701
(XEN) Xen heap: 00000000fa000000-00000000fe000000 (16384 pages)
(XEN) Dom heap: 503808 pages
(XEN) Domain heap initialised
(XEN) Platform: TI OMAP5
(XEN) Looking for dtuart at "serial2", options ""
 Xen 4.7-unstable
(XEN) Xen version 4.7-unstable (root@) (arm-linux-gnueabihf-gcc (Linaro GCC 2014.11) 4.9.3 20141031 (prerelease)) debug=y Tue Mar  1 15:02:30 CET 2016
(XEN) Latest ChangeSet: Sun Feb 28 16:03:51 2016 -0500 git:42391c6
(XEN) Console output is synchronous.
(XEN) Processor: 412fc0f2: "ARM Limited", variant: 0x2, part 0xc0f, rev 0x2
(XEN) 32-bit Execution:
(XEN)   Processor Features: 00001131:00011011
(XEN)     Instruction Sets: AArch32 A32 Thumb Thumb-2 ThumbEE Jazelle
(XEN)     Extensions: GenericTimer Security
(XEN)   Debug Features: 02010555
(XEN)   Auxiliary Features: 00000000
(XEN)   Memory Model Features: 10201105 20000000 01240000 02102211
(XEN)  ISA Features: 02101110 13112111 21232041 11112131 10011142 00000000
(XEN) Set AuxCoreBoot1 to 00000000fee0004c (0020004c)
(XEN) Set AuxCoreBoot0 to 0x20
(XEN) Generic Timer IRQ: phys=30 hyp=26 virt=27 Freq: 6144 KHz
(XEN) GICv2: WARNING: The GICC size is too small: 0x1000 expected 0x2000
(XEN) GICv2 initialization:
(XEN)         gic_dist_addr=0000000048211000
(XEN)         gic_cpu_addr=0000000048212000
(XEN)         gic_hyp_addr=0000000048214000
(XEN)         gic_vcpu_addr=0000000048216000
(XEN)         gic_maintenance_irq=25
(XEN) GICv2: 192 lines, 2 cpus, secure (IID 0000043b).
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Allocated console ring of 16 KiB.
(XEN) VFP implementer 0x41 architecture 4 part 0x30 variant 0xf rev 0x0
(XEN) Bringing up CPU1
- CPU 00000001 booting -
- Xen starting in Hyp mode -
- Setting up control registers -
- Turning on paging -
- Ready -
(XEN) CPU 1 booted.
(XEN) Brought up 2 CPUs
(XEN) P2M: 40-bit IPA
(XEN) P2M: 3 levels with order-1 root, VTCR 0x80003558
(XEN) I/O virtualisation disabled
(XEN) *** LOADING DOMAIN 0 ***
(XEN) Loading kernel from boot module @ 00000000a0000000
(XEN) Allocating 1:1 mappings totalling 128MB for dom0:
(XEN) BANK[0] 0x000000a8000000-0x000000b0000000 (128MB)
(XEN) Grant table range: 0x000000fee00000-0x000000fee63000
(XEN) Loading zImage from 00000000a0000000 to 00000000afa00000-00000000afe15d48
(XEN) Allocating PPI 16 for event channel interrupt
(XEN) Loading dom0 DTB to 0x00000000af800000-0x00000000af80aece
(XEN) Scrubbing Free RAM on 1 nodes using 2 CPUs
(XEN) ........done.
(XEN) Initial low memory virq threshold set at 0x4000 pages.
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All
(XEN) **********************************************
(XEN) ******* WARNING: CONSOLE OUTPUT IS SYNCHRONOUS
(XEN) ******* This option is intended to aid debugging of Xen by ensuring
(XEN) ******* that all output is synchronously delivered on the serial line.
(XEN) ******* However it can introduce SIGNIFICANT latencies and affect
(XEN) ******* timekeeping. It is NOT recommended for production use!
(XEN) **********************************************
(XEN) 3... 2... 1...
(XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen)
(XEN) Freed 280kB init memory.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.15.0-rc2-00199-g0c0a3e5-dirty (safa@safa-VirtualBox) (gcc version 4.9.2 (Ubuntu/Linaro 4.9.2-10ubuntu10) ) #6 SMP Mon Mar 14 18:14:21 CET 2016
[    0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] Machine model: TI OMAP5 uEVM board
[    0.000000] debug: ignoring loglevel setting.
[    0.000000] cma: CMA: reserved 16 MiB at ae800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 32512
[    0.000000] free_area_init_node: node 0, pgdat c085ce00, node_mem_map c7df2000
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32512 pages, LIFO batch:7
[    0.000000] psci: probing function IDs from device-tree
[    0.000000] OMAP5432 ES2.0
[    0.000000] PERCPU: Embedded 9 pages/cpu @c7db0000 s14784 r8192 d13888 u36864
[    0.000000] pcpu-alloc: s14784 r8192 d13888 u36864 alloc=9*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32256
[    0.000000] Kernel command line: console=hvc0,115200n8 earlyprintk=xen debug ignore_loglevel root=/dev/mmcblk0p2 rw rootwait fixrtc
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 98080K/130048K available (5672K kernel code, 441K rwdata, 2092K rodata, 342K init, 5534K bss, 31968K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff000000   ( 872 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc079d4c4   (7766 kB)
[    0.000000]       .init : 0xc079e000 - 0xc07f39c0   ( 343 kB)
[    0.000000]       .data : 0xc07f4000 - 0xc0862600   ( 442 kB)
[    0.000000]        .bss : 0xc0862600 - 0xc0dc9f00   (5535 kB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] OMAP clockevent source: timer1 at 32768 Hz
[    0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65536000000000ns
[    0.000000] OMAP clocksource: 32k_counter at 32768 Hz
[    0.000305] Architected cp15 timer(s) running at 6.14MHz (virt).
[    0.000309] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 2796202663936ns
[    0.000315] Switching to timer-based delay loop
[    0.001115] Console: colour dummy device 80x30
[    0.001145] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[    0.001152] ... MAX_LOCKDEP_SUBCLASSES:  8
[    0.001157] ... MAX_LOCK_DEPTH:          48
[    0.001163] ... MAX_LOCKDEP_KEYS:        8191
[    0.001168] ... CLASSHASH_SIZE:          4096
[    0.001173] ... MAX_LOCKDEP_ENTRIES:     16384
[    0.001178] ... MAX_LOCKDEP_CHAINS:      32768
[    0.001182] ... CHAINHASH_SIZE:          16384
[    0.001188]  memory used by lock dependency info: 3695 kB
[    0.001193]  per task-struct memory footprint: 1152 bytes
[    0.001213] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.28 BogoMIPS (lpj=61440)
[    0.001224] pid_max: default: 32768 minimum: 301
[    0.001515] Security Framework initialized
[    0.001608] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001617] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.003039] CPU: Testing write buffer coherency: ok
[    0.003679] /cpus/cpu@0 missing clock-frequency property
[    0.003705] /cpus/cpu@1 missing clock-frequency property
[    0.003714] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.003847] Xen 4.7 support found, events_irq=16 gnttab_frame=0xfee00000
[    0.004015] xen:grant_table: Grant tables using version 1 layout
[    0.004053] Grant table initialized
[    0.004103] xen:events: Using FIFO-based ABI
[    0.004125] Xen: initializing cpu0
[    0.004182] Setting up static identity map for 0xa8568c20 - 0xa8568c90
[    0.007160] CPU1: Booted secondary processor
[    0.007222] Xen: initializing cpu1
[    0.007261] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.007599] Brought up 2 CPUs
[    0.007612] SMP: Total of 2 processors activated.
[    0.007617] CPU: All CPU(s) started in SVC mode.
[    0.009402] devtmpfs: initialized
[    0.018309] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    0.019398] omap_hwmod: l3_main_3 using broken dt data from ocp
[    0.020420] omap_hwmod: l3_main_2 using broken dt data from ocp
[    0.041658] ------------[ cut here ]------------
[    0.041676] WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2538 _init+0x38c/0x3dc()
[    0.041682] omap_hwmod: mailbox: doesn't have mpu register target base
[    0.041687] Modules linked in:
[    0.041700] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.15.0-rc2-00199-g0c0a3e5-dirty #6
[    0.041718] [<c0015b04>] (unwind_backtrace) from [<c0012848>] (show_stack+0x10/0x14)
[    0.041732] [<c0012848>] (show_stack) from [<c055d608>] (dump_stack+0x84/0x9c)
[    0.041746] [<c055d608>] (dump_stack) from [<c0039b00>] (warn_slowpath_common+0x68/0x8c)
[    0.041757] [<c0039b00>] (warn_slowpath_common) from [<c0039b54>] (warn_slowpath_fmt+0x30/0x40)
[    0.041770] [<c0039b54>] (warn_slowpath_fmt) from [<c07aa4c4>] (_init+0x38c/0x3dc)
[    0.041784] [<c07aa4c4>] (_init) from [<c00281e0>] (omap_hwmod_for_each+0x34/0x60)
[    0.041795] [<c00281e0>] (omap_hwmod_for_each) from [<c07aa9b0>] (__omap_hwmod_setup_all+0x24/0x40)
[    0.041806] [<c07aa9b0>] (__omap_hwmod_setup_all) from [<c000896c>] (do_one_initcall+0xe8/0x158)
[    0.041819] [<c000896c>] (do_one_initcall) from [<c079ec10>] (kernel_init_freeable+0x100/0x1c4)
[    0.041830] [<c079ec10>] (kernel_init_freeable) from [<c05592c0>] (kernel_init+0x8/0xec)
[    0.041842] [<c05592c0>] (kernel_init) from [<c000ee68>] (ret_from_fork+0x14/0x2c)
[    0.041880] ---[ end trace 7920d429778a6b5c ]---
[    0.066049] ------------[ cut here ]------------
[    0.066062] WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2538 _init+0x38c/0x3dc()
[    0.066069] omap_hwmod: uart3: doesn't have mpu register target base
[    0.066073] Modules linked in:
[    0.066084] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G        W     3.15.0-rc2-00199-g0c0a3e5-dirty #6
[    0.066097] [<c0015b04>] (unwind_backtrace) from [<c0012848>] (show_stack+0x10/0x14)
[    0.066108] [<c0012848>] (show_stack) from [<c055d608>] (dump_stack+0x84/0x9c)
[    0.066120] [<c055d608>] (dump_stack) from [<c0039b00>] (warn_slowpath_common+0x68/0x8c)
[    0.066131] [<c0039b00>] (warn_slowpath_common) from [<c0039b54>] (warn_slowpath_fmt+0x30/0x40)
[    0.066143] [<c0039b54>] (warn_slowpath_fmt) from [<c07aa4c4>] (_init+0x38c/0x3dc)
[    0.066155] [<c07aa4c4>] (_init) from [<c00281e0>] (omap_hwmod_for_each+0x34/0x60)
[    0.066166] [<c00281e0>] (omap_hwmod_for_each) from [<c07aa9b0>] (__omap_hwmod_setup_all+0x24/0x40)
[    0.066177] [<c07aa9b0>] (__omap_hwmod_setup_all) from [<c000896c>] (do_one_initcall+0xe8/0x158)
[    0.066188] [<c000896c>] (do_one_initcall) from [<c079ec10>] (kernel_init_freeable+0x100/0x1c4)
[    0.066199] [<c079ec10>] (kernel_init_freeable) from [<c05592c0>] (kernel_init+0x8/0xec)
[    0.066209] [<c05592c0>] (kernel_init) from [<c000ee68>] (ret_from_fork+0x14/0x2c)
[    0.066215] ---[ end trace 7920d429778a6b5d ]---
[    0.115735] pinctrl core: initialized pinctrl subsystem
[    0.117384] regulator-dummy: no parameters
[    0.148783] NET: Registered protocol family 16
[    0.152399] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.154718] xen:swiotlb_xen: Warning: only able to allocate 8 MB for software IO TLB
[    0.156824] software IO TLB [mem 0xad000000-0xad800000] (8MB) mapped at [c5000000-c57fffff]
[    0.172613] gpiochip_add: registered GPIOs 0 to 31 on device: gpio
[    0.173184] OMAP GPIO hardware version 0.1
[    0.173881] gpiochip_add: registered GPIOs 32 to 63 on device: gpio
[    0.175095] gpiochip_add: registered GPIOs 64 to 95 on device: gpio
[    0.176273] gpiochip_add: registered GPIOs 96 to 127 on device: gpio
[    0.177467] gpiochip_add: registered GPIOs 128 to 159 on device: gpio
[    0.178697] gpiochip_add: registered GPIOs 160 to 191 on device: gpio
[    0.179865] gpiochip_add: registered GPIOs 192 to 223 on device: gpio
[    0.181047] gpiochip_add: registered GPIOs 224 to 255 on device: gpio
[    0.181873] platform 50000000.gpmc: Cannot lookup hwmod 'gpmc'
[    0.182047] omap-gpmc 50000000.gpmc: _od_fail_runtime_resume: FIXME: missing hwmod/omap_dev info
[    0.182062] omap-gpmc 50000000.gpmc: GPMC revision 6.0
[    0.199543] No ATAGs?
[    0.199637] hw-breakpoint: Failed to enable monitor mode on CPU 0.
[    0.201312] OMAP DMA hardware revision 0.0
[    0.218416] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot
[    0.218453] edma-dma-engine: probe of edma-dma-engine.0 failed with error -5
[    0.242352] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver
[    0.242663] xen:balloon: Initialising balloon driver
[    0.243011] xen_balloon: Initialising balloon driver
[    0.243768] of_get_named_gpiod_flags: can't parse gpios property of node '/fixedregulator-mmcsd[0]'
[    0.244107] vmmcsd_fixed: 3000 mV
[    0.246875] SCSI subsystem initialized
[    0.247403] usbcore: registered new interface driver usbfs
[    0.247521] usbcore: registered new interface driver hub
[    0.247739] usbcore: registered new device driver usb
[    0.248034] of_get_named_gpiod_flags exited with status 0
[    0.248078] hsusb2_phy.4 supply vcc not found, using dummy regulator
[    0.248445] of_get_named_gpiod_flags exited with status 0
[    0.248482] hsusb3_phy.5 supply vcc not found, using dummy regulator
[    0.249079] omap_i2c 48070000.i2c: could not find pctldev for node /ocp/pinmux@4a002840/pinmux_i2c1_pins, deferring probe
[    0.249100] platform 48070000.i2c: Driver omap_i2c requests probe deferral
[    0.249860] omap_i2c 48072000.i2c: bus 1 rev0.12 at 100 kHz
[    0.250464] omap_i2c 48060000.i2c: bus 2 rev0.12 at 100 kHz
[    0.251048] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 100 kHz
[    0.251117] omap_i2c 4807c000.i2c: could not find pctldev for node /ocp/pinmux@4a002840/pinmux_i2c5_pins, deferring probe
[    0.251137] platform 4807c000.i2c: Driver omap_i2c requests probe deferral
[    0.253809] Switched to clocksource arch_sys_counter
[    0.343964] /thermal-zones/cpu_thermal/cooling-maps/map0: could not find phandle
[    0.343975] missing cooling_device property
[    0.343985] failed to build thermal zone cpu_thermal: -22
[    0.344840] NET: Registered protocol family 2
[    0.345926] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.346021] TCP bind hash table entries: 1024 (order: 3, 36864 bytes)
[    0.346306] TCP: Hash tables configured (established 1024 bind 1024)
[    0.346377] TCP: reno registered
[    0.346394] UDP hash table entries: 256 (order: 2, 20480 bytes)
[    0.346539] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[    0.347277] NET: Registered protocol family 1
[    0.348104] RPC: Registered named UNIX socket transport module.
[    0.348113] RPC: Registered udp transport module.
[    0.348120] RPC: Registered tcp transport module.
[    0.348127] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.352189] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.444169] VFS: Disk quotas dquot_6.5.2
[    0.444270] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.446013] NFS: Registering the id_resolver key type
[    0.446222] Key type id_resolver registered
[    0.446234] Key type id_legacy registered
[    0.446298] jffs2: version 2.2. (NAND) (SUMMARY)  Â© 2001-2006 Red Hat, Inc.
[    0.446883] msgmni has been set to 223
[    0.448962] io scheduler noop registered
[    0.448972] io scheduler deadline registered
[    0.449071] io scheduler cfq registered (default)
[    0.452169] pinctrl-single 4a002840.pinmux: 219 pins at pa fc002840 size 438
[    0.452494] pinctrl-single 4ae0c840.pinmux: 28 pins at pa fce0c840 size 56
[    0.454820] xen:xen_evtchn: Event-channel device installed
[    0.456206] pbias_mmc_omap5: 1800 <--> 3000 mV at 3000 mV
[    1.596803] console [hvc0] enabled
[    1.600320] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.610569] omap_uart 4806a000.serial: no wakeirq for uart0
[    1.612277] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@4806a000[0]'
[    1.621835] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 104, base_baud = 3000000) is a OMAP UART0
[    1.631724] omap_uart 4806c000.serial: no wakeirq for uart0
[    1.636481] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@4806c000[0]'
[    1.645825] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 105, base_baud = 3000000) is a OMAP UART1
[    1.656047] omap_uart 4806e000.serial: no wakeirq for uart0
[    1.660586] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@4806e000[0]'
[    1.669965] 4806e000.serial: ttyO3 at MMIO 0x4806e000 (irq = 102, base_baud = 3000000) is a OMAP UART3
[    1.679855] omap_uart 48066000.serial: no wakeirq for uart0
[    1.684819] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@48066000[0]'
[    1.694130] 48066000.serial: ttyO4 at MMIO 0x48066000 (irq = 137, base_baud = 3000000) is a OMAP UART4
[    1.703960] omap_uart 48068000.serial: no wakeirq for uart0
[    1.708896] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@48068000[0]'
[    1.718255] 48068000.serial: ttyO5 at MMIO 0x48068000 (irq = 138, base_baud = 3000000) is a OMAP UART5
[    1.742766] brd: module loaded
[    1.750884] loop: module loaded
[    1.753014] mtdoops: mtd device (mtddev=name/number) must be supplied
[    1.759336] xen_netfront: Initialising Xen virtual ethernet driver
[    1.761573] usbcore: registered new interface driver asix
[    1.766921] usbcore: registered new interface driver ax88179_178a
[    1.773061] usbcore: registered new interface driver cdc_ether
[    1.779050] usbcore: registered new interface driver smsc95xx
[    1.784854] usbcore: registered new interface driver net1080
[    1.790599] usbcore: registered new interface driver cdc_subset
[    1.796636] usbcore: registered new interface driver zaurus
[    1.802323] usbcore: registered new interface driver cdc_ncm
[    1.808547] usbcore: registered new interface driver cdc_wdm
[    1.813872] usbcore: registered new interface driver usb-storage
[    1.819940] usbcore: registered new interface driver usbtest
[    1.826825] mousedev: PS/2 mouse device common for all mice
[    1.832999] i2c /dev entries driver
[    1.836167] Driver for 1-wire Dallas network protocol.
[    1.842305] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[    1.847437] xen_wdt: Xen WatchDog Timer Driver v0.01
[    1.852498] xen_wdt: cannot register miscdev on minor=130 (-16)
[    1.858117] wdt: probe of wdt failed with error -16
[    1.863712] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]'
[    1.871857] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]'
[    1.881916] omap_hsmmc 4809c000.mmc: pins are not configured from the driver
[    1.923830] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480b4000[0]'
[    1.926990] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480b4000[0]'
[    1.936168] omap_hsmmc 480b4000.mmc: pins are not configured from the driver
[    1.959525] mmc0: host does not support reading read-only switch. assuming write-enable.
[    1.962164] mmc0: new SDHC card at address 0001
[    1.967872] mmcblk0: mmc0:0001 Team 3.71 GiB
[    1.973840] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480ad000[0]'
[    1.979958] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480ad000[0]'
[    1.983851]  mmcblk0: p1 p2
[    1.991853] 480ad000.mmc supply vmmc not found, using dummy regulator
[    1.998376] omap_hsmmc 480ad000.mmc: pins are not configured from the driver
[    2.005661] omap_hsmmc 480ad000.mmc: could not set regulator OCR (-22)
[    2.043817] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480d1000[0]'
[    2.046988] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480d1000[0]'
[    2.055992] 480d1000.mmc supply vmmc not found, using dummy regulator
[    2.056760] mmc1: BKOPS_EN bit is not set
[    2.059364] mmc1: new high speed MMC card at address 0001
[    2.072079] omap_hsmmc 480d1000.mmc: could not set regulator OCR (-22)
[    2.073811] mmcblk1: mmc1:0001 SEM04G 3.68 GiB
[    2.074048] mmcblk1boot0: mmc1:0001 SEM04G partition 1 2.00 MiB
[    2.074291] mmcblk1boot1: mmc1:0001 SEM04G partition 2 2.00 MiB
[    2.078427] Alternate GPT is invalid, using primary GPT.
[    2.078444]  mmcblk1: p1 p2 p3 p4 p5 p6 p7
[    2.083838]  mmcblk1boot1: unknown partition table
[    2.086027]  mmcblk1boot0: unknown partition table
[    2.114607] omap_hsmmc 480d1000.mmc: pins are not configured from the driver
[    2.121951] omap_hsmmc 480d1000.mmc: could not set regulator OCR (-22)
[    2.163840] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480d5000[0]'
[    2.166999] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480d5000[0]'
[    2.176026] 480d5000.mmc supply vmmc not found, using dummy regulator
[    2.182463] omap_hsmmc 480d5000.mmc: could not set regulator OCR (-22)
[    2.189017] omap_hsmmc 480d5000.mmc: pins are not configured from the driver
[    2.196402] omap_hsmmc 480d5000.mmc: could not set regulator OCR (-22)
[    2.234283] usbcore: registered new interface driver usbhid
[    2.234383] usbhid: USB HID core driver
[    2.239037] oprofile: no performance counters
[    2.243250] oprofile: using timer interrupt.
[    2.247320] TCP: cubic registered
[    2.250433] Initializing XFRM netlink socket
[    2.254855] NET: Registered protocol family 17
[    2.259367] NET: Registered protocol family 15
[    2.264072] Key type dns_resolver registered
[    2.268932] ThumbEE CPU extension supported.
[    2.272598] Registering SWP/SWPB emulation handler
[    2.282613] palmas 0-0048: Irq flag is 0x00000000
[    2.287428] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0
[    2.328791] smps123: 600 <--> 1500 mV at 1060 mV
[    2.332072] smps45: 600 <--> 1310 mV at 1030 mV
[    2.336652] smps6: 1200 mV
[    2.339842] smps7: 1800 mV
[    2.342932] smps8: 600 <--> 1310 mV at 1040 mV
[    2.346011] smps9: 2100 mV
[    2.348275] smps10_out2: 5000 mV
[    2.351260] smps10_out1: 5000 mV
[    2.353777] ldo1: 1500 <--> 1800 mV
[    2.358517] ldo2: 2800 mV
[    2.362135] ldo3: 1500 mV
[    2.363802] ldo4: 1500 <--> 1800 mV
[    2.368464] ldo5: 1800 mV
[    2.372898] ldo6: 1200 mV
[    2.375134] ldo7: 2000 mV
[    2.378081] ldo8: 3000 mV
[    2.380662] ldo9: 1800 <--> 3000 mV at 3000 mV
[    2.384241] ldoln: 1800 mV
[    2.387238] ldousb: 3250 mV
[    2.388537] REGEN1: no parameters
[    2.391024] REGEN2: no parameters
[    2.394775] regen3: no parameters
[    2.398352] SYSEN1: no parameters
[    2.401215] SYSEN2: no parameters
[    2.404489] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
[    2.411055] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz
[    2.416843] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    2.448585] EXT3-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240)
[    2.453480] EXT2-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (244)
[    2.602885] EXT4-fs (mmcblk0p2): recovery complete
[    2.605400] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    2.610379] VFS: Mounted root (ext4 filesystem) on device 179:2.
[    2.623192] devtmpfs: mounted
[    2.623584] Freeing unused kernel memory: 340K (c079e000 - c07f3000)
INIT: version 2.88 booting
Starting udev
[    3.169771] udev[871]: starting version 164
[    5.205065] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[    5.400187] EXT4-fs (mmcblk1p4): recovery complete
[    5.400309] EXT4-fs (mmcblk1p4): mounted filesystem with ordered data mode. Opts: (null)
[    5.492162] random: nonblocking pool is initialized
ERROR: could not open directory /lib/modules/3.15.0-rc2-00199-g0c0a3e5-dirty: No such file or directory
WARNING: -e needs -E or -F
ERROR: could not open directory /lib/modules/3.15.0-rc2-00199-g0c0a3e5-dirty: No such file or directory
FATAL: could not search modules: No such file or directory
Starting Bootlog daemon: bootlogd: cannot allocate pseudo tty: No such file or directory
bootlogd.
[    5.831227] EXT4-fs (mmcblk0p2): re-mounted. Opts: data="">
ALSA: Restoring mixer settings...
Configuring network interfaces... /usr/sbin/alsactl: load_state:1686: No soundcards found...
ifconfig: SIOCGIFFLAGS: No such device
done.
hwclock: can't open '/dev/misc/rtc': No such file or directory
Mon Jul  1 15:13:00 UTC 2013
hwclock: can't open '/dev/misc/rtc': No such file or directory
INIT: Entering runlevel: 5
Starting telnet daemon.
hwclock: can't open '/dev/misc/rtc': No such file or directory
Starting syslogd/klogd: done
Starting thttpd.
Stopping Bootlog daemon: bootlogd.

***************************************************************************************************************************************************
 no console appears .. i guess the problem in the file system ... but this file works fine with the linux kernel in omap5 without  the xen hypervisor 

should i make any changement in the rootfs so it can works with xen hypervisor !! or any other solution !!
Regards


On Fri, Mar 11, 2016 at 6:16 PM, Wei Liu <wei.liu2@xxxxxxxxxx> wrote:
Add back xen-devel

On Fri, Mar 11, 2016 at 05:23:22PM +0100, Safa Hamza wrote:
> ok .. can u tell me how compile xen with debug symbols !!  i have xen-syms
> after compiling xen with "make dist-xen XEN_TARGET_ARCH=arm32
> CROSS_COMPILE=arm-linux-gnueabihf- CONFIG_EARLY_PRINTK=omap5432"   is this
> the kernel  with  debug symbols
>

I'm not sure if you did the right thing because I've never done any ARM
development. I'll let other people answer your question.

Wei.

> On Fri, Mar 11, 2016 at 5:09 PM, Wei Liu <wei.liu2@xxxxxxxxxx> wrote:
>
> > On Fri, Mar 11, 2016 at 11:02:26AM -0500, Konrad Rzeszutek Wilk wrote:
> > > On Fri, Mar 11, 2016 at 04:47:47PM +0100, Safa Hamza wrote:
> > > > now i did just like u said ...  a new error appears
> > >
> > > Adding XEn-devel back. Please reply all.
> > >
> > > >
> > ******************************************************************************
> > > > U-Boot# fdt addr $dtb_addr_r
> > > > U-Boot# fdt resize
> > > > U-Boot# fdt set /chosen xen,xen-bootargs \"$xen_bootargs\"
> > > > U-Boot# fdt resize
> > > > U-Boot# fdt set /chosen xen,dom0-bootargs \"$dom0_bootargs\"
> > > > U-Boot# fdt resize
> > > > U-Boot# fdt mknode /chosen modules
> > > > U-Boot# fdt set /chosen/modules '#address-cells' <1>
> > > > U-Boot# fdt set /chosen/modules '#size-cells' <1>
> > > > U-Boot# fdt mknode /chosen/modules module@0
> > > > libfdt fdt_add_subnode(): FDT_ERR_NOSPACE
> > > >
> > ******************************************************************************
> > > > but when i wrote  fdt resize before  fdt mknode /chosen/modules
> > module@0
> > > > this error disappear but still the execution stops as i mentioned
> > before
> > > >
> >
> > The message seems quite straight-forward to me -- one of the libfdt
> > function call failed with some error.
> >
> > I'm afraid you need to do some manual debugging to figure out what went
> > wrong.
> >
> > Wei.
> >
> > > > On Fri, Mar 11, 2016 at 4:20 PM, Konrad Rzeszutek Wilk <
> > > > konrad.wilk@xxxxxxxxxx> wrote:
> > > >
> > > > > On Fri, Mar 11, 2016 at 10:20:01AM -0500, Konrad Rzeszutek Wilk
> > wrote:
> > > > > > On Fri, Mar 11, 2016 at 04:05:58PM +0100, Safa Hamza wrote:
> > > > >
> > > > > And please do not drop Xen-devel. Adding it back on.
> > > > >
> > > > > > > i did like u said but nothing change ..
> > > > > > >
> > > > > >
> > > > > > No you didn't. See below:
> > > > > > > U-Boot# setenv dom0_bootargs 'console=hvc0,115200n8
> > earlyprintk=xen
> > > > > debug'
> > > > > >
> > > > > > You still have 115200n8
> > > > >
> > >
> > > _______________________________________________
> > > Xen-devel mailing list
> > > Xen-devel@xxxxxxxxxxxxx
> > > http://lists.xen.org/xen-devel
> >

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
http://lists.xen.org/xen-devel

 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.