|
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] [Xen-devel] [PATCH v2 27/45] ARM: new VGIC: Add ACTIVE registers handlers
The active register handlers are shared between the v2 and v3 emulation,
so their implementation goes into vgic-mmio.c, to be easily referenced
from the v3 emulation as well later.
Since activation/deactivation of an interrupt may happen entirely in the
guest without it ever exiting, we need some extra logic to properly track
the active state.
For clearing the active state, we would basically have to halt the guest
to make sure this is properly propagated into the respective VCPUs.
This is not yet implemented in Xen.
Fortunately this feature is mostly used to reset a just in initialised
GIC, so chances are we are tasked to clear bits that are already zero.
Add a simple check to avoid pointless warnings in this case.
Signed-off-by: Andre Przywara <andre.przywara@xxxxxxxxxx>
---
Changelog v1 ... v2:
- print a line for every failing IRQ
xen/arch/arm/vgic/vgic-mmio-v2.c | 4 +-
xen/arch/arm/vgic/vgic-mmio.c | 91 ++++++++++++++++++++++++++++++++++++++++
xen/arch/arm/vgic/vgic-mmio.h | 11 +++++
3 files changed, 104 insertions(+), 2 deletions(-)
diff --git a/xen/arch/arm/vgic/vgic-mmio-v2.c b/xen/arch/arm/vgic/vgic-mmio-v2.c
index a48c554040..724681e0f8 100644
--- a/xen/arch/arm/vgic/vgic-mmio-v2.c
+++ b/xen/arch/arm/vgic/vgic-mmio-v2.c
@@ -101,10 +101,10 @@ static const struct vgic_register_region
vgic_v2_dist_registers[] = {
vgic_mmio_read_pending, vgic_mmio_write_cpending, 1,
VGIC_ACCESS_32bit),
REGISTER_DESC_WITH_BITS_PER_IRQ(GICD_ISACTIVER,
- vgic_mmio_read_raz, vgic_mmio_write_wi, 1,
+ vgic_mmio_read_active, vgic_mmio_write_sactive, 1,
VGIC_ACCESS_32bit),
REGISTER_DESC_WITH_BITS_PER_IRQ(GICD_ICACTIVER,
- vgic_mmio_read_raz, vgic_mmio_write_wi, 1,
+ vgic_mmio_read_active, vgic_mmio_write_cactive, 1,
VGIC_ACCESS_32bit),
REGISTER_DESC_WITH_BITS_PER_IRQ(GICD_IPRIORITYR,
vgic_mmio_read_raz, vgic_mmio_write_wi, 8,
diff --git a/xen/arch/arm/vgic/vgic-mmio.c b/xen/arch/arm/vgic/vgic-mmio.c
index 15183c112c..170017bde3 100644
--- a/xen/arch/arm/vgic/vgic-mmio.c
+++ b/xen/arch/arm/vgic/vgic-mmio.c
@@ -281,6 +281,97 @@ void vgic_mmio_write_cpending(struct vcpu *vcpu,
}
}
+/*
+ * The actual active bit for a virtual IRQ is held in the LR. Our shadow
+ * copy in struct vgic_irq is only synced when needed and may not be
+ * up-to-date all of the time.
+ * Returning the actual active state is quite costly (stopping all
+ * VCPUs processing any affected vIRQs), so we use a simple implementation
+ * to get the best possible answer.
+ */
+unsigned long vgic_mmio_read_active(struct vcpu *vcpu,
+ paddr_t addr, unsigned int len)
+{
+ uint32_t intid = VGIC_ADDR_TO_INTID(addr, 1);
+ uint32_t value = 0;
+ unsigned int i;
+
+ /* Loop over all IRQs affected by this read */
+ for ( i = 0; i < len * 8; i++ )
+ {
+ struct vgic_irq *irq = vgic_get_irq(vcpu->domain, vcpu, intid + i);
+
+ if ( irq->active )
+ value |= (1U << i);
+
+ vgic_put_irq(vcpu->domain, irq);
+ }
+
+ return value;
+}
+
+/*
+ * We don't actually support clearing the active state of an IRQ (yet).
+ * However there is a chance that most guests use this for initialization.
+ * We check whether this MMIO access would actually affect any active IRQ,
+ * and only print our warning in this case. So clearing already non-active
+ * IRQs would not be moaned about in the logs.
+ */
+void vgic_mmio_write_cactive(struct vcpu *vcpu,
+ paddr_t addr, unsigned int len,
+ unsigned long val)
+{
+ uint32_t intid = VGIC_ADDR_TO_INTID(addr, 1);
+ unsigned int i;
+
+ for_each_set_bit( i, &val, len * 8 )
+ {
+ struct vgic_irq *irq = vgic_get_irq(vcpu->domain, vcpu, intid + i);
+
+ /*
+ * If we know that the IRQ is active or we can't be sure about
+ * it (because it is currently in a CPU), log the not properly
+ * emulated MMIO access.
+ */
+ if ( irq->active || irq->vcpu )
+ printk(XENLOG_G_ERR
+ "%pv: vGICD: IRQ%u: clearing active state not supported\n",
+ vcpu, irq->intid);
+
+ vgic_put_irq(vcpu->domain, irq);
+ }
+}
+
+/*
+ * We don't actually support setting the active state of an IRQ (yet).
+ * We check whether this MMIO access would actually affect any non-active IRQ,
+ * and only print our warning in this case.
+ */
+void vgic_mmio_write_sactive(struct vcpu *vcpu,
+ paddr_t addr, unsigned int len,
+ unsigned long val)
+{
+ uint32_t intid = VGIC_ADDR_TO_INTID(addr, 1);
+ unsigned int i;
+
+ for_each_set_bit( i, &val, len * 8 )
+ {
+ struct vgic_irq *irq = vgic_get_irq(vcpu->domain, vcpu, intid + i);
+
+ /*
+ * If we know that the IRQ is not active or we can't be sure about
+ * it (because it is currently in a CPU), log the not properly
+ * emulated MMIO access.
+ */
+ if ( !irq->active || irq->vcpu )
+ printk(XENLOG_G_ERR
+ "%pv: vGICD: IRQ%u: setting active state not supported\n",
+ vcpu, irq->intid);
+
+ vgic_put_irq(vcpu->domain, irq);
+ }
+}
+
static int match_region(const void *key, const void *elt)
{
const unsigned int offset = (unsigned long)key;
diff --git a/xen/arch/arm/vgic/vgic-mmio.h b/xen/arch/arm/vgic/vgic-mmio.h
index 5c927f28b0..832e2eb3d8 100644
--- a/xen/arch/arm/vgic/vgic-mmio.h
+++ b/xen/arch/arm/vgic/vgic-mmio.h
@@ -108,6 +108,17 @@ void vgic_mmio_write_cpending(struct vcpu *vcpu,
paddr_t addr, unsigned int len,
unsigned long val);
+unsigned long vgic_mmio_read_active(struct vcpu *vcpu,
+ paddr_t addr, unsigned int len);
+
+void vgic_mmio_write_cactive(struct vcpu *vcpu,
+ paddr_t addr, unsigned int len,
+ unsigned long val);
+
+void vgic_mmio_write_sactive(struct vcpu *vcpu,
+ paddr_t addr, unsigned int len,
+ unsigned long val);
+
unsigned int vgic_v2_init_dist_iodev(struct vgic_io_device *dev);
#endif
--
2.14.1
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxxx
https://lists.xenproject.org/mailman/listinfo/xen-devel
|
 |
Lists.xenproject.org is hosted with RackSpace, monitoring our |