Xen project Mailing List

Andrii,

I have attempted to update the bootloader from the srec files created by the bitbake command.

I believe I have been able to update it, but I am still obtaining the same results. The serial output is shown below:

[    0.000161] NOTICE: BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.17
[    0.005721] NOTICE: BL2: PRR is R-Car H3 Ver2.0
[    0.010304] NOTICE: BL2: Board is Starter Kit Rev1.0
[    0.015331] NOTICE: BL2: Boot device is HyperFlash(80MHz)
[    0.020757] NOTICE: BL2: LCM state is CM
[    0.024802] NOTICE: BL2: AVS setting succeeded. DVFS_SetVID=0x53
[    0.030786] NOTICE: BL2: DDR3200(rev.0.28)NOTICE: [COLD_BOOT]NOTICE: ..0
[    0.059996] NOTICE: BL2: DRAM Split is 4ch
[    0.063882] NOTICE: BL2: QoS is default setting(rev.0.18)
[    0.069381] NOTICE: BL2: Lossy Decomp areas
[    0.073559] NOTICE:       Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
[    0.080643] NOTICE:       Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
[    0.087555] NOTICE:       Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
[    0.094470] NOTICE: BL2: v1.3(release):b15fefa
[    0.098960] NOTICE: BL2: Built : 12:21:32, Dec 28 2018
[    0.104147] NOTICE: BL2: Normal boot
[    0.107788] NOTICE: BL2: dst=0xe6322210 src="" len=512(0x200)
[    0.114335] NOTICE: BL2: dst=0x43f00000 src="" len=6144(0x1800)
[    0.120797] NOTICE: BL2: dst=0x44000000 src="" len=65536(0x10000)
[    0.128022] NOTICE: BL2: dst=0x44100000 src="" len=524288(0x80000)
[    0.138503] NOTICE: BL2: dst=0x50000000 src="" len=1048576(0x100000)

U-Boot 2015.04 (Dec 28 2018 - 02:46:24)

CPU: Renesas Electronics R8A7795 rev 2.0
Board: H3ULCB
I2C:   ready
DRAM: 3.9 GiB
MMC:   sh-sdhi: 0, sh-sdhi: 1
In:    serial
Out:   serial
Err:   serial
Net:   ravb
Hit any key to stop autoboot: 0
=> setenv bootargs
=> setenv serverip 192.168.1.100
=> tftp 0x48080000 xen-h3ulcb.uImage
ravb Waiting for PHY auto negotiation to complete......... TIMEOUT !
Half
Using ravb device
TFTP from server 192.168.1.100; our IP address is 192.168.1.40
Filename 'xen-h3ulcb.uImage'.
Load address: 0x48080000
Loading: *
ARP Retry count exceeded; starting again
ravb:0 is connected to ravb. Reconnecting to ravb
ravb Waiting for PHY auto negotiation to complete......... TIMEOUT !
Half

ARP Retry count exceeded; starting again
ravb:0 is connected to ravb. Reconnecting to ravb
ravb Waiting for PHY auto negotiation to complete... done
ravb: 1000Base/Full
Using ravb device
TFTP from server 192.168.1.100; our IP address is 192.168.1.40
Filename 'xen-h3ulcb.uImage'.
Load address: 0x48080000
Loading: ###########################################################
         25.4 MiB/s
done
Bytes transferred = 852368 (d0190 hex)
=> tftp 0x48000000 Image-r8a7795-h3ulcb-xen-local.dtb
ravb:0 is connected to ravb. Reconnecting to ravb
ravb Waiting for PHY auto negotiation to complete..... done
ravb: 1000Base/Full
Using ravb device
TFTP from server 192.168.1.100; our IP address is 192.168.1.40
Filename 'Image-r8a7795-h3ulcb-xen-local.dtb'.
Load address: 0x48000000
Loading: #####
         11.7 KiB/s
done
Bytes transferred = 63778 (f922 hex)
=> tftp 0x7a000000 h3ulcb-image
ravb:0 is connected to ravb. Reconnecting to ravb
ravb Waiting for PHY auto negotiation to complete... done
ravb: 1000Base/Full
Using ravb device
TFTP from server 192.168.1.100; our IP address is 192.168.1.40
Filename 'h3ulcb-image'.
Load address: 0x7a000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ########################################
         2.1 MiB/s
done
Bytes transferred = 15843840 (f1c200 hex)
=> bootm 0x48080000 - 0x48000000
## Booting kernel from Legacy Image at 48080000 ...
   Image Name:   XEN
   Image Type:   AArch64 Linux Kernel Image (uncompressed)
   Data Size:    852304 Bytes = 832.3 KiB
   Load Address: 78080000
   Entry Point: 78080000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 48000000
   Booting using the fdt blob at 0x48000000
   Loading Kernel Image ... OK
   Using Device Tree in place at 0000000048000000, end 0000000048012921

Starting kernel ...

</end output>

I have noticed that the uboot date has not changed from 2015.04 although the build date is from the last time I ran a bitbake command.

I do not know what version of uboot should be used without breaking the current compiling versions.

Are there any other modifications that I can attempt?

Thank you very much for your time and patience.

Best regards,

Jairo

Re: [Xen-devel] RT Xen on ARM - R-Car series