[Xen-users] Could not get the network to run

[Friedmund Lassmann <lassmann@xxxxxxxxxx>]

Hi Folks,

I've tried to compile/install the xen-unstable-src.tgz from today 
and it works fine (at least xend start) but I can not start the network, 
not even for Domain-0! I'm using the Broadcom Corporation NetXtreme 
BCM5782 Gigabit Ethernet controller.
(I've recompiled the xen kernel after the 'make world' to get the
smbfs module, but I don't think the kernel is bad since it works fine
if I start it outside from xen)

What could I try next?

My settings are:

manxmaus:~ # ifconfig
eth0      Link encap:Ethernet  HWaddr FE:FF:FF:FF:FF:FF
          UP BROADCAST NOARP MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:17

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:27567 errors:0 dropped:0 overruns:0 frame:0
          TX packets:27567 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:4477653 (4.2 Mb)  TX bytes:4477653 (4.2 Mb)

veth0     Link encap:Ethernet  HWaddr 00:30:6E:B0:B8:08
          inet addr:15.136.125.167  Bcast:15.136.127.255  Mask:255.255.248.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:131 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 b)  TX bytes:6275 (6.1 Kb)

vif0.0    Link encap:Ethernet  HWaddr FE:FF:FF:FF:FF:FF
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:130 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:6185 (6.0 Kb)  TX bytes:0 (0.0 b)

manxmaus:~ # route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
15.136.120.0    0.0.0.0         255.255.248.0   U     0      0        0 veth0
169.254.0.0     0.0.0.0         255.255.0.0     U     0      0        0 veth0
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
0.0.0.0         15.136.127.254  0.0.0.0         UG    0      0        0 veth0

manxmaus:~ # brctl show
bridge name     bridge id               STP enabled     interfaces
xen-br0         8000.feffffffffff       no              vif0.0
                                                        eth0

end of dmesg output:

device vif0.0 entered promiscuous mode
xen-br0: port 1(vif0.0) entering learning state
xen-br0: topology change detected, propagating
xen-br0: port 1(vif0.0) entering forwarding state
bridge: can't decode speed from eth0: 65535
device eth0 entered promiscuous mode




_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users